esp-idf/components/esp32/include/soc/rmt_reg.h

2172 wiersze
105 KiB
C
Czysty Wina Historia

This file contains ambiguous Unicode characters!

This file contains ambiguous Unicode characters that may be confused with others in your current locale. If your use case is intentional and legitimate, you can safely ignore this warning. Use the Escape button to highlight these characters.

// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#ifndef _SOC_RMT_REG_H_
#define _SOC_RMT_REG_H_
#include "soc.h"
#define RMT_CH0DATA_REG (DR_REG_RMT_BASE + 0x0000)
#define RMT_CH1DATA_REG (DR_REG_RMT_BASE + 0x0004)
#define RMT_CH2DATA_REG (DR_REG_RMT_BASE + 0x0008)
#define RMT_CH3DATA_REG (DR_REG_RMT_BASE + 0x000c)
#define RMT_CH4DATA_REG (DR_REG_RMT_BASE + 0x0010)
#define RMT_CH5DATA_REG (DR_REG_RMT_BASE + 0x0014)
#define RMT_CH6DATA_REG (DR_REG_RMT_BASE + 0x0018)
#define RMT_CH7DATA_REG (DR_REG_RMT_BASE + 0x001c)
#define RMT_CH0CONF0_REG (DR_REG_RMT_BASE + 0x0020)
/* RMT_CLK_EN : R/W ;bitpos:[31] ;default: 1'h0 ; */
/*description: This bit is used to control clock.when software config RMT
internal registers it controls the register clock.*/
#define RMT_CLK_EN (BIT(31))
#define RMT_CLK_EN_M (BIT(31))
#define RMT_CLK_EN_V 0x1
#define RMT_CLK_EN_S 31
/* RMT_MEM_PD : R/W ;bitpos:[30] ;default: 1'b0 ; */
/*description: This bit is used to reduce power consumed by mem. 1:mem is in low power state.*/
#define RMT_MEM_PD (BIT(30))
#define RMT_MEM_PD_M (BIT(30))
#define RMT_MEM_PD_V 0x1
#define RMT_MEM_PD_S 30
/* RMT_CARRIER_OUT_LV_CH0 : R/W ;bitpos:[29] ;default: 1'b1 ; */
/*description: This bit is used to configure the way carrier wave is modulated
for channel0.1'b1:transmit on low output level 1'b0:transmit on high output level.*/
#define RMT_CARRIER_OUT_LV_CH0 (BIT(29))
#define RMT_CARRIER_OUT_LV_CH0_M (BIT(29))
#define RMT_CARRIER_OUT_LV_CH0_V 0x1
#define RMT_CARRIER_OUT_LV_CH0_S 29
/* RMT_CARRIER_EN_CH0 : R/W ;bitpos:[28] ;default: 1'b1 ; */
/*description: This is the carrier modulation enable control bit for channel0.*/
#define RMT_CARRIER_EN_CH0 (BIT(28))
#define RMT_CARRIER_EN_CH0_M (BIT(28))
#define RMT_CARRIER_EN_CH0_V 0x1
#define RMT_CARRIER_EN_CH0_S 28
/* RMT_MEM_SIZE_CH0 : R/W ;bitpos:[27:24] ;default: 4'h1 ; */
/*description: This register is used to configure the the amount of memory blocks
allocated to channel0.*/
#define RMT_MEM_SIZE_CH0 0x0000000F
#define RMT_MEM_SIZE_CH0_M ((RMT_MEM_SIZE_CH0_V)<<(RMT_MEM_SIZE_CH0_S))
#define RMT_MEM_SIZE_CH0_V 0xF
#define RMT_MEM_SIZE_CH0_S 24
/* RMT_IDLE_THRES_CH0 : R/W ;bitpos:[23:8] ;default: 16'h1000 ; */
/*description: In receive mode when no edge is detected on the input signal
for longer than reg_idle_thres_ch0 then the receive process is done.*/
#define RMT_IDLE_THRES_CH0 0x0000FFFF
#define RMT_IDLE_THRES_CH0_M ((RMT_IDLE_THRES_CH0_V)<<(RMT_IDLE_THRES_CH0_S))
#define RMT_IDLE_THRES_CH0_V 0xFFFF
#define RMT_IDLE_THRES_CH0_S 8
/* RMT_DIV_CNT_CH0 : R/W ;bitpos:[7:0] ;default: 8'h2 ; */
/*description: This register is used to configure the frequency divider's factor in channel0.*/
#define RMT_DIV_CNT_CH0 0x000000FF
#define RMT_DIV_CNT_CH0_M ((RMT_DIV_CNT_CH0_V)<<(RMT_DIV_CNT_CH0_S))
#define RMT_DIV_CNT_CH0_V 0xFF
#define RMT_DIV_CNT_CH0_S 0
#define RMT_CH0CONF1_REG (DR_REG_RMT_BASE + 0x0024)
/* RMT_IDLE_OUT_EN_CH0 : R/W ;bitpos:[19] ;default: 1'b0 ; */
/*description: This is the output enable control bit for channel0 in IDLE state.*/
#define RMT_IDLE_OUT_EN_CH0 (BIT(19))
#define RMT_IDLE_OUT_EN_CH0_M (BIT(19))
#define RMT_IDLE_OUT_EN_CH0_V 0x1
#define RMT_IDLE_OUT_EN_CH0_S 19
/* RMT_IDLE_OUT_LV_CH0 : R/W ;bitpos:[18] ;default: 1'b0 ; */
/*description: This bit configures the output signal's level for channel0 in IDLE state.*/
#define RMT_IDLE_OUT_LV_CH0 (BIT(18))
#define RMT_IDLE_OUT_LV_CH0_M (BIT(18))
#define RMT_IDLE_OUT_LV_CH0_V 0x1
#define RMT_IDLE_OUT_LV_CH0_S 18
/* RMT_REF_ALWAYS_ON_CH0 : R/W ;bitpos:[17] ;default: 1'b0 ; */
/*description: This bit is used to select base clock. 1'b1:clk_apb 1'b0:clk_ref*/
#define RMT_REF_ALWAYS_ON_CH0 (BIT(17))
#define RMT_REF_ALWAYS_ON_CH0_M (BIT(17))
#define RMT_REF_ALWAYS_ON_CH0_V 0x1
#define RMT_REF_ALWAYS_ON_CH0_S 17
/* RMT_REF_CNT_RST_CH0 : R/W ;bitpos:[16] ;default: 1'b0 ; */
/*description: This bit is used to reset divider in channel0.*/
#define RMT_REF_CNT_RST_CH0 (BIT(16))
#define RMT_REF_CNT_RST_CH0_M (BIT(16))
#define RMT_REF_CNT_RST_CH0_V 0x1
#define RMT_REF_CNT_RST_CH0_S 16
/* RMT_RX_FILTER_THRES_CH0 : R/W ;bitpos:[15:8] ;default: 8'hf ; */
/*description: in receive mode channel0 ignore input pulse when the pulse width
is smaller then this value.*/
#define RMT_RX_FILTER_THRES_CH0 0x000000FF
#define RMT_RX_FILTER_THRES_CH0_M ((RMT_RX_FILTER_THRES_CH0_V)<<(RMT_RX_FILTER_THRES_CH0_S))
#define RMT_RX_FILTER_THRES_CH0_V 0xFF
#define RMT_RX_FILTER_THRES_CH0_S 8
/* RMT_RX_FILTER_EN_CH0 : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: This is the receive filter enable bit for channel0.*/
#define RMT_RX_FILTER_EN_CH0 (BIT(7))
#define RMT_RX_FILTER_EN_CH0_M (BIT(7))
#define RMT_RX_FILTER_EN_CH0_V 0x1
#define RMT_RX_FILTER_EN_CH0_S 7
/* RMT_TX_CONTI_MODE_CH0 : R/W ;bitpos:[6] ;default: 1'b0 ; */
/*description: Set this bit to continue sending from the first data to the
last data in channel0 again and again.*/
#define RMT_TX_CONTI_MODE_CH0 (BIT(6))
#define RMT_TX_CONTI_MODE_CH0_M (BIT(6))
#define RMT_TX_CONTI_MODE_CH0_V 0x1
#define RMT_TX_CONTI_MODE_CH0_S 6
/* RMT_MEM_OWNER_CH0 : R/W ;bitpos:[5] ;default: 1'b1 ; */
/*description: This is the mark of channel0's ram usage right.1'b1receiver
uses the ram 0transmitter uses the ram*/
#define RMT_MEM_OWNER_CH0 (BIT(5))
#define RMT_MEM_OWNER_CH0_M (BIT(5))
#define RMT_MEM_OWNER_CH0_V 0x1
#define RMT_MEM_OWNER_CH0_S 5
/* RMT_APB_MEM_RST_CH0 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: Set this bit to reset W/R ram address for channel0 by apb fifo access*/
#define RMT_APB_MEM_RST_CH0 (BIT(4))
#define RMT_APB_MEM_RST_CH0_M (BIT(4))
#define RMT_APB_MEM_RST_CH0_V 0x1
#define RMT_APB_MEM_RST_CH0_S 4
/* RMT_MEM_RD_RST_CH0 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to reset read ram address for channel0 by transmitter access.*/
#define RMT_MEM_RD_RST_CH0 (BIT(3))
#define RMT_MEM_RD_RST_CH0_M (BIT(3))
#define RMT_MEM_RD_RST_CH0_V 0x1
#define RMT_MEM_RD_RST_CH0_S 3
/* RMT_MEM_WR_RST_CH0 : R/W ;bitpos:[2] ;default: 1'h0 ; */
/*description: Set this bit to reset write ram address for channel0 by receiver access.*/
#define RMT_MEM_WR_RST_CH0 (BIT(2))
#define RMT_MEM_WR_RST_CH0_M (BIT(2))
#define RMT_MEM_WR_RST_CH0_V 0x1
#define RMT_MEM_WR_RST_CH0_S 2
/* RMT_RX_EN_CH0 : R/W ;bitpos:[1] ;default: 1'h0 ; */
/*description: Set this bit to enbale receving data for channel0.*/
#define RMT_RX_EN_CH0 (BIT(1))
#define RMT_RX_EN_CH0_M (BIT(1))
#define RMT_RX_EN_CH0_V 0x1
#define RMT_RX_EN_CH0_S 1
/* RMT_TX_START_CH0 : R/W ;bitpos:[0] ;default: 1'h0 ; */
/*description: Set this bit to start sending data for channel0.*/
#define RMT_TX_START_CH0 (BIT(0))
#define RMT_TX_START_CH0_M (BIT(0))
#define RMT_TX_START_CH0_V 0x1
#define RMT_TX_START_CH0_S 0
#define RMT_CH1CONF0_REG (DR_REG_RMT_BASE + 0x0028)
/* RMT_CARRIER_OUT_LV_CH1 : R/W ;bitpos:[29] ;default: 1'b1 ; */
/*description: This bit is used to configure the way carrier wave is modulated
for channel1.1'b1:transmit on low output level 1'b0:transmit on high output level.*/
#define RMT_CARRIER_OUT_LV_CH1 (BIT(29))
#define RMT_CARRIER_OUT_LV_CH1_M (BIT(29))
#define RMT_CARRIER_OUT_LV_CH1_V 0x1
#define RMT_CARRIER_OUT_LV_CH1_S 29
/* RMT_CARRIER_EN_CH1 : R/W ;bitpos:[28] ;default: 1'b1 ; */
/*description: This is the carrier modulation enable control bit for channel1.*/
#define RMT_CARRIER_EN_CH1 (BIT(28))
#define RMT_CARRIER_EN_CH1_M (BIT(28))
#define RMT_CARRIER_EN_CH1_V 0x1
#define RMT_CARRIER_EN_CH1_S 28
/* RMT_MEM_SIZE_CH1 : R/W ;bitpos:[27:24] ;default: 4'h1 ; */
/*description: This register is used to configure the the amount of memory blocks
allocated to channel1.*/
#define RMT_MEM_SIZE_CH1 0x0000000F
#define RMT_MEM_SIZE_CH1_M ((RMT_MEM_SIZE_CH1_V)<<(RMT_MEM_SIZE_CH1_S))
#define RMT_MEM_SIZE_CH1_V 0xF
#define RMT_MEM_SIZE_CH1_S 24
/* RMT_IDLE_THRES_CH1 : R/W ;bitpos:[23:8] ;default: 16'h1000 ; */
/*description: This register is used to configure the the amount of memory blocks
allocated to channel1.*/
#define RMT_IDLE_THRES_CH1 0x0000FFFF
#define RMT_IDLE_THRES_CH1_M ((RMT_IDLE_THRES_CH1_V)<<(RMT_IDLE_THRES_CH1_S))
#define RMT_IDLE_THRES_CH1_V 0xFFFF
#define RMT_IDLE_THRES_CH1_S 8
/* RMT_DIV_CNT_CH1 : R/W ;bitpos:[7:0] ;default: 8'h2 ; */
/*description: This register is used to configure the frequency divider's factor in channel1.*/
#define RMT_DIV_CNT_CH1 0x000000FF
#define RMT_DIV_CNT_CH1_M ((RMT_DIV_CNT_CH1_V)<<(RMT_DIV_CNT_CH1_S))
#define RMT_DIV_CNT_CH1_V 0xFF
#define RMT_DIV_CNT_CH1_S 0
#define RMT_CH1CONF1_REG (DR_REG_RMT_BASE + 0x002c)
/* RMT_IDLE_OUT_EN_CH1 : R/W ;bitpos:[19] ;default: 1'b0 ; */
/*description: This is the output enable control bit for channel1 in IDLE state.*/
#define RMT_IDLE_OUT_EN_CH1 (BIT(19))
#define RMT_IDLE_OUT_EN_CH1_M (BIT(19))
#define RMT_IDLE_OUT_EN_CH1_V 0x1
#define RMT_IDLE_OUT_EN_CH1_S 19
/* RMT_IDLE_OUT_LV_CH1 : R/W ;bitpos:[18] ;default: 1'b0 ; */
/*description: This bit configures the output signal's level for channel1 in IDLE state.*/
#define RMT_IDLE_OUT_LV_CH1 (BIT(18))
#define RMT_IDLE_OUT_LV_CH1_M (BIT(18))
#define RMT_IDLE_OUT_LV_CH1_V 0x1
#define RMT_IDLE_OUT_LV_CH1_S 18
/* RMT_REF_ALWAYS_ON_CH1 : R/W ;bitpos:[17] ;default: 1'b0 ; */
/*description: This bit is used to select base clock. 1'b1:clk_apb 1'b0:clk_ref*/
#define RMT_REF_ALWAYS_ON_CH1 (BIT(17))
#define RMT_REF_ALWAYS_ON_CH1_M (BIT(17))
#define RMT_REF_ALWAYS_ON_CH1_V 0x1
#define RMT_REF_ALWAYS_ON_CH1_S 17
/* RMT_REF_CNT_RST_CH1 : R/W ;bitpos:[16] ;default: 1'b0 ; */
/*description: This bit is used to reset divider in channel1.*/
#define RMT_REF_CNT_RST_CH1 (BIT(16))
#define RMT_REF_CNT_RST_CH1_M (BIT(16))
#define RMT_REF_CNT_RST_CH1_V 0x1
#define RMT_REF_CNT_RST_CH1_S 16
/* RMT_RX_FILTER_THRES_CH1 : R/W ;bitpos:[15:8] ;default: 8'hf ; */
/*description: in receive mode channel1 ignore input pulse when the pulse width
is smaller then this value.*/
#define RMT_RX_FILTER_THRES_CH1 0x000000FF
#define RMT_RX_FILTER_THRES_CH1_M ((RMT_RX_FILTER_THRES_CH1_V)<<(RMT_RX_FILTER_THRES_CH1_S))
#define RMT_RX_FILTER_THRES_CH1_V 0xFF
#define RMT_RX_FILTER_THRES_CH1_S 8
/* RMT_RX_FILTER_EN_CH1 : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: This is the receive filter enable bit for channel1.*/
#define RMT_RX_FILTER_EN_CH1 (BIT(7))
#define RMT_RX_FILTER_EN_CH1_M (BIT(7))
#define RMT_RX_FILTER_EN_CH1_V 0x1
#define RMT_RX_FILTER_EN_CH1_S 7
/* RMT_TX_CONTI_MODE_CH1 : R/W ;bitpos:[6] ;default: 1'b0 ; */
/*description: Set this bit to continue sending from the first data to the
last data in channel1 again and again.*/
#define RMT_TX_CONTI_MODE_CH1 (BIT(6))
#define RMT_TX_CONTI_MODE_CH1_M (BIT(6))
#define RMT_TX_CONTI_MODE_CH1_V 0x1
#define RMT_TX_CONTI_MODE_CH1_S 6
/* RMT_MEM_OWNER_CH1 : R/W ;bitpos:[5] ;default: 1'b1 ; */
/*description: This is the mark of channel1's ram usage right.1'b1receiver
uses the ram 0transmitter uses the ram*/
#define RMT_MEM_OWNER_CH1 (BIT(5))
#define RMT_MEM_OWNER_CH1_M (BIT(5))
#define RMT_MEM_OWNER_CH1_V 0x1
#define RMT_MEM_OWNER_CH1_S 5
/* RMT_APB_MEM_RST_CH1 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: Set this bit to reset W/R ram address for channel1 by apb fifo access*/
#define RMT_APB_MEM_RST_CH1 (BIT(4))
#define RMT_APB_MEM_RST_CH1_M (BIT(4))
#define RMT_APB_MEM_RST_CH1_V 0x1
#define RMT_APB_MEM_RST_CH1_S 4
/* RMT_MEM_RD_RST_CH1 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to reset read ram address for channel1 by transmitter access.*/
#define RMT_MEM_RD_RST_CH1 (BIT(3))
#define RMT_MEM_RD_RST_CH1_M (BIT(3))
#define RMT_MEM_RD_RST_CH1_V 0x1
#define RMT_MEM_RD_RST_CH1_S 3
/* RMT_MEM_WR_RST_CH1 : R/W ;bitpos:[2] ;default: 1'h0 ; */
/*description: Set this bit to reset write ram address for channel1 by receiver access.*/
#define RMT_MEM_WR_RST_CH1 (BIT(2))
#define RMT_MEM_WR_RST_CH1_M (BIT(2))
#define RMT_MEM_WR_RST_CH1_V 0x1
#define RMT_MEM_WR_RST_CH1_S 2
/* RMT_RX_EN_CH1 : R/W ;bitpos:[1] ;default: 1'h0 ; */
/*description: Set this bit to enbale receving data for channel1.*/
#define RMT_RX_EN_CH1 (BIT(1))
#define RMT_RX_EN_CH1_M (BIT(1))
#define RMT_RX_EN_CH1_V 0x1
#define RMT_RX_EN_CH1_S 1
/* RMT_TX_START_CH1 : R/W ;bitpos:[0] ;default: 1'h0 ; */
/*description: Set this bit to start sending data for channel1.*/
#define RMT_TX_START_CH1 (BIT(0))
#define RMT_TX_START_CH1_M (BIT(0))
#define RMT_TX_START_CH1_V 0x1
#define RMT_TX_START_CH1_S 0
#define RMT_CH2CONF0_REG (DR_REG_RMT_BASE + 0x0030)
/* RMT_CARRIER_OUT_LV_CH2 : R/W ;bitpos:[29] ;default: 1'b1 ; */
/*description: This bit is used to configure carrier wave's position for channel2.1'b1:add
on low level 1'b0:add on high level.*/
#define RMT_CARRIER_OUT_LV_CH2 (BIT(29))
#define RMT_CARRIER_OUT_LV_CH2_M (BIT(29))
#define RMT_CARRIER_OUT_LV_CH2_V 0x1
#define RMT_CARRIER_OUT_LV_CH2_S 29
/* RMT_CARRIER_EN_CH2 : R/W ;bitpos:[28] ;default: 1'b1 ; */
/*description: This is the carrier modulation enable control bit for channel2.*/
#define RMT_CARRIER_EN_CH2 (BIT(28))
#define RMT_CARRIER_EN_CH2_M (BIT(28))
#define RMT_CARRIER_EN_CH2_V 0x1
#define RMT_CARRIER_EN_CH2_S 28
/* RMT_MEM_SIZE_CH2 : R/W ;bitpos:[27:24] ;default: 4'h1 ; */
/*description: This register is used to configure the the amount of memory blocks
allocated to channel2.*/
#define RMT_MEM_SIZE_CH2 0x0000000F
#define RMT_MEM_SIZE_CH2_M ((RMT_MEM_SIZE_CH2_V)<<(RMT_MEM_SIZE_CH2_S))
#define RMT_MEM_SIZE_CH2_V 0xF
#define RMT_MEM_SIZE_CH2_S 24
/* RMT_IDLE_THRES_CH2 : R/W ;bitpos:[23:8] ;default: 16'h1000 ; */
/*description: In receive mode when the counter's value is bigger than reg_idle_thres_ch2
then the receive process is done.*/
#define RMT_IDLE_THRES_CH2 0x0000FFFF
#define RMT_IDLE_THRES_CH2_M ((RMT_IDLE_THRES_CH2_V)<<(RMT_IDLE_THRES_CH2_S))
#define RMT_IDLE_THRES_CH2_V 0xFFFF
#define RMT_IDLE_THRES_CH2_S 8
/* RMT_DIV_CNT_CH2 : R/W ;bitpos:[7:0] ;default: 8'h2 ; */
/*description: This register is used to configure the frequency divider's factor in channel2.*/
#define RMT_DIV_CNT_CH2 0x000000FF
#define RMT_DIV_CNT_CH2_M ((RMT_DIV_CNT_CH2_V)<<(RMT_DIV_CNT_CH2_S))
#define RMT_DIV_CNT_CH2_V 0xFF
#define RMT_DIV_CNT_CH2_S 0
#define RMT_CH2CONF1_REG (DR_REG_RMT_BASE + 0x0034)
/* RMT_IDLE_OUT_EN_CH2 : R/W ;bitpos:[19] ;default: 1'b0 ; */
/*description: This is the output enable control bit for channel2 in IDLE state.*/
#define RMT_IDLE_OUT_EN_CH2 (BIT(19))
#define RMT_IDLE_OUT_EN_CH2_M (BIT(19))
#define RMT_IDLE_OUT_EN_CH2_V 0x1
#define RMT_IDLE_OUT_EN_CH2_S 19
/* RMT_IDLE_OUT_LV_CH2 : R/W ;bitpos:[18] ;default: 1'b0 ; */
/*description: This bit configures the output signal's level for channel2 in IDLE state.*/
#define RMT_IDLE_OUT_LV_CH2 (BIT(18))
#define RMT_IDLE_OUT_LV_CH2_M (BIT(18))
#define RMT_IDLE_OUT_LV_CH2_V 0x1
#define RMT_IDLE_OUT_LV_CH2_S 18
/* RMT_REF_ALWAYS_ON_CH2 : R/W ;bitpos:[17] ;default: 1'b0 ; */
/*description: This bit is used to select base clock. 1'b1:clk_apb 1'b0:clk_ref*/
#define RMT_REF_ALWAYS_ON_CH2 (BIT(17))
#define RMT_REF_ALWAYS_ON_CH2_M (BIT(17))
#define RMT_REF_ALWAYS_ON_CH2_V 0x1
#define RMT_REF_ALWAYS_ON_CH2_S 17
/* RMT_REF_CNT_RST_CH2 : R/W ;bitpos:[16] ;default: 1'b0 ; */
/*description: This bit is used to reset divider in channel2.*/
#define RMT_REF_CNT_RST_CH2 (BIT(16))
#define RMT_REF_CNT_RST_CH2_M (BIT(16))
#define RMT_REF_CNT_RST_CH2_V 0x1
#define RMT_REF_CNT_RST_CH2_S 16
/* RMT_RX_FILTER_THRES_CH2 : R/W ;bitpos:[15:8] ;default: 8'hf ; */
/*description: in receive mode channel2 ignore input pulse when the pulse width
is smaller then this value.*/
#define RMT_RX_FILTER_THRES_CH2 0x000000FF
#define RMT_RX_FILTER_THRES_CH2_M ((RMT_RX_FILTER_THRES_CH2_V)<<(RMT_RX_FILTER_THRES_CH2_S))
#define RMT_RX_FILTER_THRES_CH2_V 0xFF
#define RMT_RX_FILTER_THRES_CH2_S 8
/* RMT_RX_FILTER_EN_CH2 : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: This is the receive filter enable bit for channel2.*/
#define RMT_RX_FILTER_EN_CH2 (BIT(7))
#define RMT_RX_FILTER_EN_CH2_M (BIT(7))
#define RMT_RX_FILTER_EN_CH2_V 0x1
#define RMT_RX_FILTER_EN_CH2_S 7
/* RMT_TX_CONTI_MODE_CH2 : R/W ;bitpos:[6] ;default: 1'b0 ; */
/*description: Set this bit to continue sending from the first data to the
last data in channel2.*/
#define RMT_TX_CONTI_MODE_CH2 (BIT(6))
#define RMT_TX_CONTI_MODE_CH2_M (BIT(6))
#define RMT_TX_CONTI_MODE_CH2_V 0x1
#define RMT_TX_CONTI_MODE_CH2_S 6
/* RMT_MEM_OWNER_CH2 : R/W ;bitpos:[5] ;default: 1'b1 ; */
/*description: This is the mark of channel2's ram usage right.1'b1receiver
uses the ram 0transmitter uses the ram*/
#define RMT_MEM_OWNER_CH2 (BIT(5))
#define RMT_MEM_OWNER_CH2_M (BIT(5))
#define RMT_MEM_OWNER_CH2_V 0x1
#define RMT_MEM_OWNER_CH2_S 5
/* RMT_APB_MEM_RST_CH2 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: Set this bit to reset W/R ram address for channel2 by apb fifo access*/
#define RMT_APB_MEM_RST_CH2 (BIT(4))
#define RMT_APB_MEM_RST_CH2_M (BIT(4))
#define RMT_APB_MEM_RST_CH2_V 0x1
#define RMT_APB_MEM_RST_CH2_S 4
/* RMT_MEM_RD_RST_CH2 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to reset read ram address for channel2 by transmitter access.*/
#define RMT_MEM_RD_RST_CH2 (BIT(3))
#define RMT_MEM_RD_RST_CH2_M (BIT(3))
#define RMT_MEM_RD_RST_CH2_V 0x1
#define RMT_MEM_RD_RST_CH2_S 3
/* RMT_MEM_WR_RST_CH2 : R/W ;bitpos:[2] ;default: 1'h0 ; */
/*description: Set this bit to reset write ram address for channel2 by receiver access.*/
#define RMT_MEM_WR_RST_CH2 (BIT(2))
#define RMT_MEM_WR_RST_CH2_M (BIT(2))
#define RMT_MEM_WR_RST_CH2_V 0x1
#define RMT_MEM_WR_RST_CH2_S 2
/* RMT_RX_EN_CH2 : R/W ;bitpos:[1] ;default: 1'h0 ; */
/*description: Set this bit to enbale receving data for channel2.*/
#define RMT_RX_EN_CH2 (BIT(1))
#define RMT_RX_EN_CH2_M (BIT(1))
#define RMT_RX_EN_CH2_V 0x1
#define RMT_RX_EN_CH2_S 1
/* RMT_TX_START_CH2 : R/W ;bitpos:[0] ;default: 1'h0 ; */
/*description: Set this bit to start sending data for channel2.*/
#define RMT_TX_START_CH2 (BIT(0))
#define RMT_TX_START_CH2_M (BIT(0))
#define RMT_TX_START_CH2_V 0x1
#define RMT_TX_START_CH2_S 0
#define RMT_CH3CONF0_REG (DR_REG_RMT_BASE + 0x0038)
/* RMT_CARRIER_OUT_LV_CH3 : R/W ;bitpos:[29] ;default: 1'b1 ; */
/*description: This bit is used to configure carrier wave's position for channel3.1'b1:add
on low level 1'b0:add on high level.*/
#define RMT_CARRIER_OUT_LV_CH3 (BIT(29))
#define RMT_CARRIER_OUT_LV_CH3_M (BIT(29))
#define RMT_CARRIER_OUT_LV_CH3_V 0x1
#define RMT_CARRIER_OUT_LV_CH3_S 29
/* RMT_CARRIER_EN_CH3 : R/W ;bitpos:[28] ;default: 1'b1 ; */
/*description: This is the carrier modulation enable control bit for channel3.*/
#define RMT_CARRIER_EN_CH3 (BIT(28))
#define RMT_CARRIER_EN_CH3_M (BIT(28))
#define RMT_CARRIER_EN_CH3_V 0x1
#define RMT_CARRIER_EN_CH3_S 28
/* RMT_MEM_SIZE_CH3 : R/W ;bitpos:[27:24] ;default: 4'h1 ; */
/*description: This register is used to configure the the amount of memory blocks
allocated to channel3.*/
#define RMT_MEM_SIZE_CH3 0x0000000F
#define RMT_MEM_SIZE_CH3_M ((RMT_MEM_SIZE_CH3_V)<<(RMT_MEM_SIZE_CH3_S))
#define RMT_MEM_SIZE_CH3_V 0xF
#define RMT_MEM_SIZE_CH3_S 24
/* RMT_IDLE_THRES_CH3 : R/W ;bitpos:[23:8] ;default: 16'h1000 ; */
/*description: In receive mode when the counter's value is bigger than reg_idle_thres_ch3
then the receive process is done.*/
#define RMT_IDLE_THRES_CH3 0x0000FFFF
#define RMT_IDLE_THRES_CH3_M ((RMT_IDLE_THRES_CH3_V)<<(RMT_IDLE_THRES_CH3_S))
#define RMT_IDLE_THRES_CH3_V 0xFFFF
#define RMT_IDLE_THRES_CH3_S 8
/* RMT_DIV_CNT_CH3 : R/W ;bitpos:[7:0] ;default: 8'h2 ; */
/*description: This register is used to configure the frequency divider's factor in channel3.*/
#define RMT_DIV_CNT_CH3 0x000000FF
#define RMT_DIV_CNT_CH3_M ((RMT_DIV_CNT_CH3_V)<<(RMT_DIV_CNT_CH3_S))
#define RMT_DIV_CNT_CH3_V 0xFF
#define RMT_DIV_CNT_CH3_S 0
#define RMT_CH3CONF1_REG (DR_REG_RMT_BASE + 0x003c)
/* RMT_IDLE_OUT_EN_CH3 : R/W ;bitpos:[19] ;default: 1'b0 ; */
/*description: This is the output enable control bit for channel3 in IDLE state.*/
#define RMT_IDLE_OUT_EN_CH3 (BIT(19))
#define RMT_IDLE_OUT_EN_CH3_M (BIT(19))
#define RMT_IDLE_OUT_EN_CH3_V 0x1
#define RMT_IDLE_OUT_EN_CH3_S 19
/* RMT_IDLE_OUT_LV_CH3 : R/W ;bitpos:[18] ;default: 1'b0 ; */
/*description: This bit configures the output signal's level for channel3 in IDLE state.*/
#define RMT_IDLE_OUT_LV_CH3 (BIT(18))
#define RMT_IDLE_OUT_LV_CH3_M (BIT(18))
#define RMT_IDLE_OUT_LV_CH3_V 0x1
#define RMT_IDLE_OUT_LV_CH3_S 18
/* RMT_REF_ALWAYS_ON_CH3 : R/W ;bitpos:[17] ;default: 1'b0 ; */
/*description: This bit is used to select base clock. 1'b1:clk_apb 1'b0:clk_ref*/
#define RMT_REF_ALWAYS_ON_CH3 (BIT(17))
#define RMT_REF_ALWAYS_ON_CH3_M (BIT(17))
#define RMT_REF_ALWAYS_ON_CH3_V 0x1
#define RMT_REF_ALWAYS_ON_CH3_S 17
/* RMT_REF_CNT_RST_CH3 : R/W ;bitpos:[16] ;default: 1'b0 ; */
/*description: This bit is used to reset divider in channel3.*/
#define RMT_REF_CNT_RST_CH3 (BIT(16))
#define RMT_REF_CNT_RST_CH3_M (BIT(16))
#define RMT_REF_CNT_RST_CH3_V 0x1
#define RMT_REF_CNT_RST_CH3_S 16
/* RMT_RX_FILTER_THRES_CH3 : R/W ;bitpos:[15:8] ;default: 8'hf ; */
/*description: in receive mode channel3 ignore input pulse when the pulse width
is smaller then this value.*/
#define RMT_RX_FILTER_THRES_CH3 0x000000FF
#define RMT_RX_FILTER_THRES_CH3_M ((RMT_RX_FILTER_THRES_CH3_V)<<(RMT_RX_FILTER_THRES_CH3_S))
#define RMT_RX_FILTER_THRES_CH3_V 0xFF
#define RMT_RX_FILTER_THRES_CH3_S 8
/* RMT_RX_FILTER_EN_CH3 : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: This is the receive filter enable bit for channel3.*/
#define RMT_RX_FILTER_EN_CH3 (BIT(7))
#define RMT_RX_FILTER_EN_CH3_M (BIT(7))
#define RMT_RX_FILTER_EN_CH3_V 0x1
#define RMT_RX_FILTER_EN_CH3_S 7
/* RMT_TX_CONTI_MODE_CH3 : R/W ;bitpos:[6] ;default: 1'b0 ; */
/*description: Set this bit to continue sending from the first data to the
last data in channel3.*/
#define RMT_TX_CONTI_MODE_CH3 (BIT(6))
#define RMT_TX_CONTI_MODE_CH3_M (BIT(6))
#define RMT_TX_CONTI_MODE_CH3_V 0x1
#define RMT_TX_CONTI_MODE_CH3_S 6
/* RMT_MEM_OWNER_CH3 : R/W ;bitpos:[5] ;default: 1'b1 ; */
/*description: This is the mark of channel3's ram usage right.1'b1receiver
uses the ram 0transmitter uses the ram*/
#define RMT_MEM_OWNER_CH3 (BIT(5))
#define RMT_MEM_OWNER_CH3_M (BIT(5))
#define RMT_MEM_OWNER_CH3_V 0x1
#define RMT_MEM_OWNER_CH3_S 5
/* RMT_APB_MEM_RST_CH3 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: Set this bit to reset W/R ram address for channel3 by apb fifo access*/
#define RMT_APB_MEM_RST_CH3 (BIT(4))
#define RMT_APB_MEM_RST_CH3_M (BIT(4))
#define RMT_APB_MEM_RST_CH3_V 0x1
#define RMT_APB_MEM_RST_CH3_S 4
/* RMT_MEM_RD_RST_CH3 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to reset read ram address for channel3 by transmitter access.*/
#define RMT_MEM_RD_RST_CH3 (BIT(3))
#define RMT_MEM_RD_RST_CH3_M (BIT(3))
#define RMT_MEM_RD_RST_CH3_V 0x1
#define RMT_MEM_RD_RST_CH3_S 3
/* RMT_MEM_WR_RST_CH3 : R/W ;bitpos:[2] ;default: 1'h0 ; */
/*description: Set this bit to reset write ram address for channel3 by receiver access.*/
#define RMT_MEM_WR_RST_CH3 (BIT(2))
#define RMT_MEM_WR_RST_CH3_M (BIT(2))
#define RMT_MEM_WR_RST_CH3_V 0x1
#define RMT_MEM_WR_RST_CH3_S 2
/* RMT_RX_EN_CH3 : R/W ;bitpos:[1] ;default: 1'h0 ; */
/*description: Set this bit to enbale receving data for channel3.*/
#define RMT_RX_EN_CH3 (BIT(1))
#define RMT_RX_EN_CH3_M (BIT(1))
#define RMT_RX_EN_CH3_V 0x1
#define RMT_RX_EN_CH3_S 1
/* RMT_TX_START_CH3 : R/W ;bitpos:[0] ;default: 1'h0 ; */
/*description: Set this bit to start sending data for channel3.*/
#define RMT_TX_START_CH3 (BIT(0))
#define RMT_TX_START_CH3_M (BIT(0))
#define RMT_TX_START_CH3_V 0x1
#define RMT_TX_START_CH3_S 0
#define RMT_CH4CONF0_REG (DR_REG_RMT_BASE + 0x0040)
/* RMT_CARRIER_OUT_LV_CH4 : R/W ;bitpos:[29] ;default: 1'b1 ; */
/*description: This bit is used to configure carrier wave's position for channel4.1'b1:add
on low level 1'b0:add on high level.*/
#define RMT_CARRIER_OUT_LV_CH4 (BIT(29))
#define RMT_CARRIER_OUT_LV_CH4_M (BIT(29))
#define RMT_CARRIER_OUT_LV_CH4_V 0x1
#define RMT_CARRIER_OUT_LV_CH4_S 29
/* RMT_CARRIER_EN_CH4 : R/W ;bitpos:[28] ;default: 1'b1 ; */
/*description: This is the carrier modulation enable control bit for channel4.*/
#define RMT_CARRIER_EN_CH4 (BIT(28))
#define RMT_CARRIER_EN_CH4_M (BIT(28))
#define RMT_CARRIER_EN_CH4_V 0x1
#define RMT_CARRIER_EN_CH4_S 28
/* RMT_MEM_SIZE_CH4 : R/W ;bitpos:[27:24] ;default: 4'h1 ; */
/*description: This register is used to configure the the amount of memory blocks
allocated to channel4.*/
#define RMT_MEM_SIZE_CH4 0x0000000F
#define RMT_MEM_SIZE_CH4_M ((RMT_MEM_SIZE_CH4_V)<<(RMT_MEM_SIZE_CH4_S))
#define RMT_MEM_SIZE_CH4_V 0xF
#define RMT_MEM_SIZE_CH4_S 24
/* RMT_IDLE_THRES_CH4 : R/W ;bitpos:[23:8] ;default: 16'h1000 ; */
/*description: In receive mode when the counter's value is bigger than reg_idle_thres_ch4
then the receive process is done.*/
#define RMT_IDLE_THRES_CH4 0x0000FFFF
#define RMT_IDLE_THRES_CH4_M ((RMT_IDLE_THRES_CH4_V)<<(RMT_IDLE_THRES_CH4_S))
#define RMT_IDLE_THRES_CH4_V 0xFFFF
#define RMT_IDLE_THRES_CH4_S 8
/* RMT_DIV_CNT_CH4 : R/W ;bitpos:[7:0] ;default: 8'h2 ; */
/*description: This register is used to configure the frequency divider's factor in channel4.*/
#define RMT_DIV_CNT_CH4 0x000000FF
#define RMT_DIV_CNT_CH4_M ((RMT_DIV_CNT_CH4_V)<<(RMT_DIV_CNT_CH4_S))
#define RMT_DIV_CNT_CH4_V 0xFF
#define RMT_DIV_CNT_CH4_S 0
#define RMT_CH4CONF1_REG (DR_REG_RMT_BASE + 0x0044)
/* RMT_IDLE_OUT_EN_CH4 : R/W ;bitpos:[19] ;default: 1'b0 ; */
/*description: This is the output enable control bit for channel4 in IDLE state.*/
#define RMT_IDLE_OUT_EN_CH4 (BIT(19))
#define RMT_IDLE_OUT_EN_CH4_M (BIT(19))
#define RMT_IDLE_OUT_EN_CH4_V 0x1
#define RMT_IDLE_OUT_EN_CH4_S 19
/* RMT_IDLE_OUT_LV_CH4 : R/W ;bitpos:[18] ;default: 1'b0 ; */
/*description: This bit configures the output signal's level for channel4 in IDLE state.*/
#define RMT_IDLE_OUT_LV_CH4 (BIT(18))
#define RMT_IDLE_OUT_LV_CH4_M (BIT(18))
#define RMT_IDLE_OUT_LV_CH4_V 0x1
#define RMT_IDLE_OUT_LV_CH4_S 18
/* RMT_REF_ALWAYS_ON_CH4 : R/W ;bitpos:[17] ;default: 1'b0 ; */
/*description: This bit is used to select base clock. 1'b1:clk_apb 1'b0:clk_ref*/
#define RMT_REF_ALWAYS_ON_CH4 (BIT(17))
#define RMT_REF_ALWAYS_ON_CH4_M (BIT(17))
#define RMT_REF_ALWAYS_ON_CH4_V 0x1
#define RMT_REF_ALWAYS_ON_CH4_S 17
/* RMT_REF_CNT_RST_CH4 : R/W ;bitpos:[16] ;default: 1'b0 ; */
/*description: This bit is used to reset divider in channel4.*/
#define RMT_REF_CNT_RST_CH4 (BIT(16))
#define RMT_REF_CNT_RST_CH4_M (BIT(16))
#define RMT_REF_CNT_RST_CH4_V 0x1
#define RMT_REF_CNT_RST_CH4_S 16
/* RMT_RX_FILTER_THRES_CH4 : R/W ;bitpos:[15:8] ;default: 8'hf ; */
/*description: in receive mode channel4 ignore input pulse when the pulse width
is smaller then this value.*/
#define RMT_RX_FILTER_THRES_CH4 0x000000FF
#define RMT_RX_FILTER_THRES_CH4_M ((RMT_RX_FILTER_THRES_CH4_V)<<(RMT_RX_FILTER_THRES_CH4_S))
#define RMT_RX_FILTER_THRES_CH4_V 0xFF
#define RMT_RX_FILTER_THRES_CH4_S 8
/* RMT_RX_FILTER_EN_CH4 : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: This is the receive filter enable bit for channel4.*/
#define RMT_RX_FILTER_EN_CH4 (BIT(7))
#define RMT_RX_FILTER_EN_CH4_M (BIT(7))
#define RMT_RX_FILTER_EN_CH4_V 0x1
#define RMT_RX_FILTER_EN_CH4_S 7
/* RMT_TX_CONTI_MODE_CH4 : R/W ;bitpos:[6] ;default: 1'b0 ; */
/*description: Set this bit to continue sending from the first data to the
last data in channel4.*/
#define RMT_TX_CONTI_MODE_CH4 (BIT(6))
#define RMT_TX_CONTI_MODE_CH4_M (BIT(6))
#define RMT_TX_CONTI_MODE_CH4_V 0x1
#define RMT_TX_CONTI_MODE_CH4_S 6
/* RMT_MEM_OWNER_CH4 : R/W ;bitpos:[5] ;default: 1'b1 ; */
/*description: This is the mark of channel4's ram usage right.1'b1receiver
uses the ram 0transmitter uses the ram*/
#define RMT_MEM_OWNER_CH4 (BIT(5))
#define RMT_MEM_OWNER_CH4_M (BIT(5))
#define RMT_MEM_OWNER_CH4_V 0x1
#define RMT_MEM_OWNER_CH4_S 5
/* RMT_APB_MEM_RST_CH4 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: Set this bit to reset W/R ram address for channel4 by apb fifo access*/
#define RMT_APB_MEM_RST_CH4 (BIT(4))
#define RMT_APB_MEM_RST_CH4_M (BIT(4))
#define RMT_APB_MEM_RST_CH4_V 0x1
#define RMT_APB_MEM_RST_CH4_S 4
/* RMT_MEM_RD_RST_CH4 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to reset read ram address for channel4 by transmitter access.*/
#define RMT_MEM_RD_RST_CH4 (BIT(3))
#define RMT_MEM_RD_RST_CH4_M (BIT(3))
#define RMT_MEM_RD_RST_CH4_V 0x1
#define RMT_MEM_RD_RST_CH4_S 3
/* RMT_MEM_WR_RST_CH4 : R/W ;bitpos:[2] ;default: 1'h0 ; */
/*description: Set this bit to reset write ram address for channel4 by receiver access.*/
#define RMT_MEM_WR_RST_CH4 (BIT(2))
#define RMT_MEM_WR_RST_CH4_M (BIT(2))
#define RMT_MEM_WR_RST_CH4_V 0x1
#define RMT_MEM_WR_RST_CH4_S 2
/* RMT_RX_EN_CH4 : R/W ;bitpos:[1] ;default: 1'h0 ; */
/*description: Set this bit to enbale receving data for channel4.*/
#define RMT_RX_EN_CH4 (BIT(1))
#define RMT_RX_EN_CH4_M (BIT(1))
#define RMT_RX_EN_CH4_V 0x1
#define RMT_RX_EN_CH4_S 1
/* RMT_TX_START_CH4 : R/W ;bitpos:[0] ;default: 1'h0 ; */
/*description: Set this bit to start sending data for channel4.*/
#define RMT_TX_START_CH4 (BIT(0))
#define RMT_TX_START_CH4_M (BIT(0))
#define RMT_TX_START_CH4_V 0x1
#define RMT_TX_START_CH4_S 0
#define RMT_CH5CONF0_REG (DR_REG_RMT_BASE + 0x0048)
/* RMT_CARRIER_OUT_LV_CH5 : R/W ;bitpos:[29] ;default: 1'b1 ; */
/*description: This bit is used to configure carrier wave's position for channel5.1'b1:add
on low level 1'b0:add on high level.*/
#define RMT_CARRIER_OUT_LV_CH5 (BIT(29))
#define RMT_CARRIER_OUT_LV_CH5_M (BIT(29))
#define RMT_CARRIER_OUT_LV_CH5_V 0x1
#define RMT_CARRIER_OUT_LV_CH5_S 29
/* RMT_CARRIER_EN_CH5 : R/W ;bitpos:[28] ;default: 1'b1 ; */
/*description: This is the carrier modulation enable control bit for channel5.*/
#define RMT_CARRIER_EN_CH5 (BIT(28))
#define RMT_CARRIER_EN_CH5_M (BIT(28))
#define RMT_CARRIER_EN_CH5_V 0x1
#define RMT_CARRIER_EN_CH5_S 28
/* RMT_MEM_SIZE_CH5 : R/W ;bitpos:[27:24] ;default: 4'h1 ; */
/*description: This register is used to configure the the amount of memory blocks
allocated to channel5.*/
#define RMT_MEM_SIZE_CH5 0x0000000F
#define RMT_MEM_SIZE_CH5_M ((RMT_MEM_SIZE_CH5_V)<<(RMT_MEM_SIZE_CH5_S))
#define RMT_MEM_SIZE_CH5_V 0xF
#define RMT_MEM_SIZE_CH5_S 24
/* RMT_IDLE_THRES_CH5 : R/W ;bitpos:[23:8] ;default: 16'h1000 ; */
/*description: In receive mode when the counter's value is bigger than reg_idle_thres_ch5
then the receive process is done.*/
#define RMT_IDLE_THRES_CH5 0x0000FFFF
#define RMT_IDLE_THRES_CH5_M ((RMT_IDLE_THRES_CH5_V)<<(RMT_IDLE_THRES_CH5_S))
#define RMT_IDLE_THRES_CH5_V 0xFFFF
#define RMT_IDLE_THRES_CH5_S 8
/* RMT_DIV_CNT_CH5 : R/W ;bitpos:[7:0] ;default: 8'h2 ; */
/*description: This register is used to configure the frequency divider's factor in channel5.*/
#define RMT_DIV_CNT_CH5 0x000000FF
#define RMT_DIV_CNT_CH5_M ((RMT_DIV_CNT_CH5_V)<<(RMT_DIV_CNT_CH5_S))
#define RMT_DIV_CNT_CH5_V 0xFF
#define RMT_DIV_CNT_CH5_S 0
#define RMT_CH5CONF1_REG (DR_REG_RMT_BASE + 0x004c)
/* RMT_IDLE_OUT_EN_CH5 : R/W ;bitpos:[19] ;default: 1'b0 ; */
/*description: This is the output enable control bit for channel5 in IDLE state.*/
#define RMT_IDLE_OUT_EN_CH5 (BIT(19))
#define RMT_IDLE_OUT_EN_CH5_M (BIT(19))
#define RMT_IDLE_OUT_EN_CH5_V 0x1
#define RMT_IDLE_OUT_EN_CH5_S 19
/* RMT_IDLE_OUT_LV_CH5 : R/W ;bitpos:[18] ;default: 1'b0 ; */
/*description: This bit configures the output signal's level for channel5 in IDLE state.*/
#define RMT_IDLE_OUT_LV_CH5 (BIT(18))
#define RMT_IDLE_OUT_LV_CH5_M (BIT(18))
#define RMT_IDLE_OUT_LV_CH5_V 0x1
#define RMT_IDLE_OUT_LV_CH5_S 18
/* RMT_REF_ALWAYS_ON_CH5 : R/W ;bitpos:[17] ;default: 1'b0 ; */
/*description: This bit is used to select base clock. 1'b1:clk_apb 1'b0:clk_ref*/
#define RMT_REF_ALWAYS_ON_CH5 (BIT(17))
#define RMT_REF_ALWAYS_ON_CH5_M (BIT(17))
#define RMT_REF_ALWAYS_ON_CH5_V 0x1
#define RMT_REF_ALWAYS_ON_CH5_S 17
/* RMT_REF_CNT_RST_CH5 : R/W ;bitpos:[16] ;default: 1'b0 ; */
/*description: This bit is used to reset divider in channel5.*/
#define RMT_REF_CNT_RST_CH5 (BIT(16))
#define RMT_REF_CNT_RST_CH5_M (BIT(16))
#define RMT_REF_CNT_RST_CH5_V 0x1
#define RMT_REF_CNT_RST_CH5_S 16
/* RMT_RX_FILTER_THRES_CH5 : R/W ;bitpos:[15:8] ;default: 8'hf ; */
/*description: in receive mode channel5 ignore input pulse when the pulse width
is smaller then this value.*/
#define RMT_RX_FILTER_THRES_CH5 0x000000FF
#define RMT_RX_FILTER_THRES_CH5_M ((RMT_RX_FILTER_THRES_CH5_V)<<(RMT_RX_FILTER_THRES_CH5_S))
#define RMT_RX_FILTER_THRES_CH5_V 0xFF
#define RMT_RX_FILTER_THRES_CH5_S 8
/* RMT_RX_FILTER_EN_CH5 : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: This is the receive filter enable bit for channel5.*/
#define RMT_RX_FILTER_EN_CH5 (BIT(7))
#define RMT_RX_FILTER_EN_CH5_M (BIT(7))
#define RMT_RX_FILTER_EN_CH5_V 0x1
#define RMT_RX_FILTER_EN_CH5_S 7
/* RMT_TX_CONTI_MODE_CH5 : R/W ;bitpos:[6] ;default: 1'b0 ; */
/*description: Set this bit to continue sending from the first data to the
last data in channel5.*/
#define RMT_TX_CONTI_MODE_CH5 (BIT(6))
#define RMT_TX_CONTI_MODE_CH5_M (BIT(6))
#define RMT_TX_CONTI_MODE_CH5_V 0x1
#define RMT_TX_CONTI_MODE_CH5_S 6
/* RMT_MEM_OWNER_CH5 : R/W ;bitpos:[5] ;default: 1'b1 ; */
/*description: This is the mark of channel5's ram usage right.1'b1receiver
uses the ram 0transmitter uses the ram*/
#define RMT_MEM_OWNER_CH5 (BIT(5))
#define RMT_MEM_OWNER_CH5_M (BIT(5))
#define RMT_MEM_OWNER_CH5_V 0x1
#define RMT_MEM_OWNER_CH5_S 5
/* RMT_APB_MEM_RST_CH5 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: Set this bit to reset W/R ram address for channel5 by apb fifo access*/
#define RMT_APB_MEM_RST_CH5 (BIT(4))
#define RMT_APB_MEM_RST_CH5_M (BIT(4))
#define RMT_APB_MEM_RST_CH5_V 0x1
#define RMT_APB_MEM_RST_CH5_S 4
/* RMT_MEM_RD_RST_CH5 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to reset read ram address for channel5 by transmitter access.*/
#define RMT_MEM_RD_RST_CH5 (BIT(3))
#define RMT_MEM_RD_RST_CH5_M (BIT(3))
#define RMT_MEM_RD_RST_CH5_V 0x1
#define RMT_MEM_RD_RST_CH5_S 3
/* RMT_MEM_WR_RST_CH5 : R/W ;bitpos:[2] ;default: 1'h0 ; */
/*description: Set this bit to reset write ram address for channel5 by receiver access.*/
#define RMT_MEM_WR_RST_CH5 (BIT(2))
#define RMT_MEM_WR_RST_CH5_M (BIT(2))
#define RMT_MEM_WR_RST_CH5_V 0x1
#define RMT_MEM_WR_RST_CH5_S 2
/* RMT_RX_EN_CH5 : R/W ;bitpos:[1] ;default: 1'h0 ; */
/*description: Set this bit to enbale receving data for channel5.*/
#define RMT_RX_EN_CH5 (BIT(1))
#define RMT_RX_EN_CH5_M (BIT(1))
#define RMT_RX_EN_CH5_V 0x1
#define RMT_RX_EN_CH5_S 1
/* RMT_TX_START_CH5 : R/W ;bitpos:[0] ;default: 1'h0 ; */
/*description: Set this bit to start sending data for channel5.*/
#define RMT_TX_START_CH5 (BIT(0))
#define RMT_TX_START_CH5_M (BIT(0))
#define RMT_TX_START_CH5_V 0x1
#define RMT_TX_START_CH5_S 0
#define RMT_CH6CONF0_REG (DR_REG_RMT_BASE + 0x0050)
/* RMT_CARRIER_OUT_LV_CH6 : R/W ;bitpos:[29] ;default: 1'b1 ; */
/*description: This bit is used to configure carrier wave's position for channel6.1'b1:add
on low level 1'b0:add on high level.*/
#define RMT_CARRIER_OUT_LV_CH6 (BIT(29))
#define RMT_CARRIER_OUT_LV_CH6_M (BIT(29))
#define RMT_CARRIER_OUT_LV_CH6_V 0x1
#define RMT_CARRIER_OUT_LV_CH6_S 29
/* RMT_CARRIER_EN_CH6 : R/W ;bitpos:[28] ;default: 1'b1 ; */
/*description: This is the carrier modulation enable control bit for channel6.*/
#define RMT_CARRIER_EN_CH6 (BIT(28))
#define RMT_CARRIER_EN_CH6_M (BIT(28))
#define RMT_CARRIER_EN_CH6_V 0x1
#define RMT_CARRIER_EN_CH6_S 28
/* RMT_MEM_SIZE_CH6 : R/W ;bitpos:[27:24] ;default: 4'h1 ; */
/*description: This register is used to configure the the amount of memory blocks
allocated to channel6.*/
#define RMT_MEM_SIZE_CH6 0x0000000F
#define RMT_MEM_SIZE_CH6_M ((RMT_MEM_SIZE_CH6_V)<<(RMT_MEM_SIZE_CH6_S))
#define RMT_MEM_SIZE_CH6_V 0xF
#define RMT_MEM_SIZE_CH6_S 24
/* RMT_IDLE_THRES_CH6 : R/W ;bitpos:[23:8] ;default: 16'h1000 ; */
/*description: In receive mode when the counter's value is bigger than reg_idle_thres_ch6
then the receive process is done.*/
#define RMT_IDLE_THRES_CH6 0x0000FFFF
#define RMT_IDLE_THRES_CH6_M ((RMT_IDLE_THRES_CH6_V)<<(RMT_IDLE_THRES_CH6_S))
#define RMT_IDLE_THRES_CH6_V 0xFFFF
#define RMT_IDLE_THRES_CH6_S 8
/* RMT_DIV_CNT_CH6 : R/W ;bitpos:[7:0] ;default: 8'h2 ; */
/*description: This register is used to configure the frequency divider's factor in channel6.*/
#define RMT_DIV_CNT_CH6 0x000000FF
#define RMT_DIV_CNT_CH6_M ((RMT_DIV_CNT_CH6_V)<<(RMT_DIV_CNT_CH6_S))
#define RMT_DIV_CNT_CH6_V 0xFF
#define RMT_DIV_CNT_CH6_S 0
#define RMT_CH6CONF1_REG (DR_REG_RMT_BASE + 0x0054)
/* RMT_IDLE_OUT_EN_CH6 : R/W ;bitpos:[19] ;default: 1'b0 ; */
/*description: This is the output enable control bit for channel6 in IDLE state.*/
#define RMT_IDLE_OUT_EN_CH6 (BIT(19))
#define RMT_IDLE_OUT_EN_CH6_M (BIT(19))
#define RMT_IDLE_OUT_EN_CH6_V 0x1
#define RMT_IDLE_OUT_EN_CH6_S 19
/* RMT_IDLE_OUT_LV_CH6 : R/W ;bitpos:[18] ;default: 1'b0 ; */
/*description: This bit configures the output signal's level for channel6 in IDLE state.*/
#define RMT_IDLE_OUT_LV_CH6 (BIT(18))
#define RMT_IDLE_OUT_LV_CH6_M (BIT(18))
#define RMT_IDLE_OUT_LV_CH6_V 0x1
#define RMT_IDLE_OUT_LV_CH6_S 18
/* RMT_REF_ALWAYS_ON_CH6 : R/W ;bitpos:[17] ;default: 1'b0 ; */
/*description: This bit is used to select base clock. 1'b1:clk_apb 1'b0:clk_ref*/
#define RMT_REF_ALWAYS_ON_CH6 (BIT(17))
#define RMT_REF_ALWAYS_ON_CH6_M (BIT(17))
#define RMT_REF_ALWAYS_ON_CH6_V 0x1
#define RMT_REF_ALWAYS_ON_CH6_S 17
/* RMT_REF_CNT_RST_CH6 : R/W ;bitpos:[16] ;default: 1'b0 ; */
/*description: This bit is used to reset divider in channel6.*/
#define RMT_REF_CNT_RST_CH6 (BIT(16))
#define RMT_REF_CNT_RST_CH6_M (BIT(16))
#define RMT_REF_CNT_RST_CH6_V 0x1
#define RMT_REF_CNT_RST_CH6_S 16
/* RMT_RX_FILTER_THRES_CH6 : R/W ;bitpos:[15:8] ;default: 8'hf ; */
/*description: in receive mode channel6 ignore input pulse when the pulse width
is smaller then this value.*/
#define RMT_RX_FILTER_THRES_CH6 0x000000FF
#define RMT_RX_FILTER_THRES_CH6_M ((RMT_RX_FILTER_THRES_CH6_V)<<(RMT_RX_FILTER_THRES_CH6_S))
#define RMT_RX_FILTER_THRES_CH6_V 0xFF
#define RMT_RX_FILTER_THRES_CH6_S 8
/* RMT_RX_FILTER_EN_CH6 : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: This is the receive filter enable bit for channel6.*/
#define RMT_RX_FILTER_EN_CH6 (BIT(7))
#define RMT_RX_FILTER_EN_CH6_M (BIT(7))
#define RMT_RX_FILTER_EN_CH6_V 0x1
#define RMT_RX_FILTER_EN_CH6_S 7
/* RMT_TX_CONTI_MODE_CH6 : R/W ;bitpos:[6] ;default: 1'b0 ; */
/*description: Set this bit to continue sending from the first data to the
last data in channel6.*/
#define RMT_TX_CONTI_MODE_CH6 (BIT(6))
#define RMT_TX_CONTI_MODE_CH6_M (BIT(6))
#define RMT_TX_CONTI_MODE_CH6_V 0x1
#define RMT_TX_CONTI_MODE_CH6_S 6
/* RMT_MEM_OWNER_CH6 : R/W ;bitpos:[5] ;default: 1'b1 ; */
/*description: This is the mark of channel6's ram usage right.1'b1receiver
uses the ram 0transmitter uses the ram*/
#define RMT_MEM_OWNER_CH6 (BIT(5))
#define RMT_MEM_OWNER_CH6_M (BIT(5))
#define RMT_MEM_OWNER_CH6_V 0x1
#define RMT_MEM_OWNER_CH6_S 5
/* RMT_APB_MEM_RST_CH6 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: Set this bit to reset W/R ram address for channel6 by apb fifo access*/
#define RMT_APB_MEM_RST_CH6 (BIT(4))
#define RMT_APB_MEM_RST_CH6_M (BIT(4))
#define RMT_APB_MEM_RST_CH6_V 0x1
#define RMT_APB_MEM_RST_CH6_S 4
/* RMT_MEM_RD_RST_CH6 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to reset read ram address for channel6 by transmitter access.*/
#define RMT_MEM_RD_RST_CH6 (BIT(3))
#define RMT_MEM_RD_RST_CH6_M (BIT(3))
#define RMT_MEM_RD_RST_CH6_V 0x1
#define RMT_MEM_RD_RST_CH6_S 3
/* RMT_MEM_WR_RST_CH6 : R/W ;bitpos:[2] ;default: 1'h0 ; */
/*description: Set this bit to reset write ram address for channel6 by receiver access.*/
#define RMT_MEM_WR_RST_CH6 (BIT(2))
#define RMT_MEM_WR_RST_CH6_M (BIT(2))
#define RMT_MEM_WR_RST_CH6_V 0x1
#define RMT_MEM_WR_RST_CH6_S 2
/* RMT_RX_EN_CH6 : R/W ;bitpos:[1] ;default: 1'h0 ; */
/*description: Set this bit to enbale receving data for channel6.*/
#define RMT_RX_EN_CH6 (BIT(1))
#define RMT_RX_EN_CH6_M (BIT(1))
#define RMT_RX_EN_CH6_V 0x1
#define RMT_RX_EN_CH6_S 1
/* RMT_TX_START_CH6 : R/W ;bitpos:[0] ;default: 1'h0 ; */
/*description: Set this bit to start sending data for channel6.*/
#define RMT_TX_START_CH6 (BIT(0))
#define RMT_TX_START_CH6_M (BIT(0))
#define RMT_TX_START_CH6_V 0x1
#define RMT_TX_START_CH6_S 0
#define RMT_CH7CONF0_REG (DR_REG_RMT_BASE + 0x0058)
/* RMT_CARRIER_OUT_LV_CH7 : R/W ;bitpos:[29] ;default: 1'b1 ; */
/*description: This bit is used to configure carrier wave's position for channel7.1'b1:add
on low level 1'b0:add on high level.*/
#define RMT_CARRIER_OUT_LV_CH7 (BIT(29))
#define RMT_CARRIER_OUT_LV_CH7_M (BIT(29))
#define RMT_CARRIER_OUT_LV_CH7_V 0x1
#define RMT_CARRIER_OUT_LV_CH7_S 29
/* RMT_CARRIER_EN_CH7 : R/W ;bitpos:[28] ;default: 1'b1 ; */
/*description: This is the carrier modulation enable control bit for channel7.*/
#define RMT_CARRIER_EN_CH7 (BIT(28))
#define RMT_CARRIER_EN_CH7_M (BIT(28))
#define RMT_CARRIER_EN_CH7_V 0x1
#define RMT_CARRIER_EN_CH7_S 28
/* RMT_MEM_SIZE_CH7 : R/W ;bitpos:[27:24] ;default: 4'h1 ; */
/*description: This register is used to configure the the amount of memory blocks
allocated to channel7.*/
#define RMT_MEM_SIZE_CH7 0x0000000F
#define RMT_MEM_SIZE_CH7_M ((RMT_MEM_SIZE_CH7_V)<<(RMT_MEM_SIZE_CH7_S))
#define RMT_MEM_SIZE_CH7_V 0xF
#define RMT_MEM_SIZE_CH7_S 24
/* RMT_IDLE_THRES_CH7 : R/W ;bitpos:[23:8] ;default: 16'h1000 ; */
/*description: In receive mode when the counter's value is bigger than reg_idle_thres_ch7
then the receive process is done.*/
#define RMT_IDLE_THRES_CH7 0x0000FFFF
#define RMT_IDLE_THRES_CH7_M ((RMT_IDLE_THRES_CH7_V)<<(RMT_IDLE_THRES_CH7_S))
#define RMT_IDLE_THRES_CH7_V 0xFFFF
#define RMT_IDLE_THRES_CH7_S 8
/* RMT_DIV_CNT_CH7 : R/W ;bitpos:[7:0] ;default: 8'h2 ; */
/*description: This register is used to configure the frequency divider's factor in channel7.*/
#define RMT_DIV_CNT_CH7 0x000000FF
#define RMT_DIV_CNT_CH7_M ((RMT_DIV_CNT_CH7_V)<<(RMT_DIV_CNT_CH7_S))
#define RMT_DIV_CNT_CH7_V 0xFF
#define RMT_DIV_CNT_CH7_S 0
#define RMT_CH7CONF1_REG (DR_REG_RMT_BASE + 0x005c)
/* RMT_IDLE_OUT_EN_CH7 : R/W ;bitpos:[19] ;default: 1'b0 ; */
/*description: This is the output enable control bit for channel6 in IDLE state.*/
#define RMT_IDLE_OUT_EN_CH7 (BIT(19))
#define RMT_IDLE_OUT_EN_CH7_M (BIT(19))
#define RMT_IDLE_OUT_EN_CH7_V 0x1
#define RMT_IDLE_OUT_EN_CH7_S 19
/* RMT_IDLE_OUT_LV_CH7 : R/W ;bitpos:[18] ;default: 1'b0 ; */
/*description: This bit configures the output signal's level for channel7 in IDLE state.*/
#define RMT_IDLE_OUT_LV_CH7 (BIT(18))
#define RMT_IDLE_OUT_LV_CH7_M (BIT(18))
#define RMT_IDLE_OUT_LV_CH7_V 0x1
#define RMT_IDLE_OUT_LV_CH7_S 18
/* RMT_REF_ALWAYS_ON_CH7 : R/W ;bitpos:[17] ;default: 1'b0 ; */
/*description: This bit is used to select base clock. 1'b1:clk_apb 1'b0:clk_ref*/
#define RMT_REF_ALWAYS_ON_CH7 (BIT(17))
#define RMT_REF_ALWAYS_ON_CH7_M (BIT(17))
#define RMT_REF_ALWAYS_ON_CH7_V 0x1
#define RMT_REF_ALWAYS_ON_CH7_S 17
/* RMT_REF_CNT_RST_CH7 : R/W ;bitpos:[16] ;default: 1'b0 ; */
/*description: This bit is used to reset divider in channel7.*/
#define RMT_REF_CNT_RST_CH7 (BIT(16))
#define RMT_REF_CNT_RST_CH7_M (BIT(16))
#define RMT_REF_CNT_RST_CH7_V 0x1
#define RMT_REF_CNT_RST_CH7_S 16
/* RMT_RX_FILTER_THRES_CH7 : R/W ;bitpos:[15:8] ;default: 8'hf ; */
/*description: in receive mode channel7 ignore input pulse when the pulse width
is smaller then this value.*/
#define RMT_RX_FILTER_THRES_CH7 0x000000FF
#define RMT_RX_FILTER_THRES_CH7_M ((RMT_RX_FILTER_THRES_CH7_V)<<(RMT_RX_FILTER_THRES_CH7_S))
#define RMT_RX_FILTER_THRES_CH7_V 0xFF
#define RMT_RX_FILTER_THRES_CH7_S 8
/* RMT_RX_FILTER_EN_CH7 : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: This is the receive filter enable bit for channel7.*/
#define RMT_RX_FILTER_EN_CH7 (BIT(7))
#define RMT_RX_FILTER_EN_CH7_M (BIT(7))
#define RMT_RX_FILTER_EN_CH7_V 0x1
#define RMT_RX_FILTER_EN_CH7_S 7
/* RMT_TX_CONTI_MODE_CH7 : R/W ;bitpos:[6] ;default: 1'b0 ; */
/*description: Set this bit to continue sending from the first data to the
last data in channel7.*/
#define RMT_TX_CONTI_MODE_CH7 (BIT(6))
#define RMT_TX_CONTI_MODE_CH7_M (BIT(6))
#define RMT_TX_CONTI_MODE_CH7_V 0x1
#define RMT_TX_CONTI_MODE_CH7_S 6
/* RMT_MEM_OWNER_CH7 : R/W ;bitpos:[5] ;default: 1'b1 ; */
/*description: This is the mark of channel7's ram usage right.1'b1receiver
uses the ram 0transmitter uses the ram*/
#define RMT_MEM_OWNER_CH7 (BIT(5))
#define RMT_MEM_OWNER_CH7_M (BIT(5))
#define RMT_MEM_OWNER_CH7_V 0x1
#define RMT_MEM_OWNER_CH7_S 5
/* RMT_APB_MEM_RST_CH7 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: Set this bit to reset W/R ram address for channel7 by apb fifo access*/
#define RMT_APB_MEM_RST_CH7 (BIT(4))
#define RMT_APB_MEM_RST_CH7_M (BIT(4))
#define RMT_APB_MEM_RST_CH7_V 0x1
#define RMT_APB_MEM_RST_CH7_S 4
/* RMT_MEM_RD_RST_CH7 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to reset read ram address for channel7 by transmitter access.*/
#define RMT_MEM_RD_RST_CH7 (BIT(3))
#define RMT_MEM_RD_RST_CH7_M (BIT(3))
#define RMT_MEM_RD_RST_CH7_V 0x1
#define RMT_MEM_RD_RST_CH7_S 3
/* RMT_MEM_WR_RST_CH7 : R/W ;bitpos:[2] ;default: 1'h0 ; */
/*description: Set this bit to reset write ram address for channel7 by receiver access.*/
#define RMT_MEM_WR_RST_CH7 (BIT(2))
#define RMT_MEM_WR_RST_CH7_M (BIT(2))
#define RMT_MEM_WR_RST_CH7_V 0x1
#define RMT_MEM_WR_RST_CH7_S 2
/* RMT_RX_EN_CH7 : R/W ;bitpos:[1] ;default: 1'h0 ; */
/*description: Set this bit to enbale receving data for channel7.*/
#define RMT_RX_EN_CH7 (BIT(1))
#define RMT_RX_EN_CH7_M (BIT(1))
#define RMT_RX_EN_CH7_V 0x1
#define RMT_RX_EN_CH7_S 1
/* RMT_TX_START_CH7 : R/W ;bitpos:[0] ;default: 1'h0 ; */
/*description: Set this bit to start sending data for channel7.*/
#define RMT_TX_START_CH7 (BIT(0))
#define RMT_TX_START_CH7_M (BIT(0))
#define RMT_TX_START_CH7_V 0x1
#define RMT_TX_START_CH7_S 0
#define RMT_CH0STATUS_REG (DR_REG_RMT_BASE + 0x0060)
/* RMT_STATUS_CH0 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The status for channel0*/
#define RMT_STATUS_CH0 0xFFFFFFFF
#define RMT_STATUS_CH0_M ((RMT_STATUS_CH0_V)<<(RMT_STATUS_CH0_S))
#define RMT_STATUS_CH0_V 0xFFFFFFFF
#define RMT_STATUS_CH0_S 0
#define RMT_CH1STATUS_REG (DR_REG_RMT_BASE + 0x0064)
/* RMT_STATUS_CH1 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The status for channel1*/
#define RMT_STATUS_CH1 0xFFFFFFFF
#define RMT_STATUS_CH1_M ((RMT_STATUS_CH1_V)<<(RMT_STATUS_CH1_S))
#define RMT_STATUS_CH1_V 0xFFFFFFFF
#define RMT_STATUS_CH1_S 0
#define RMT_CH2STATUS_REG (DR_REG_RMT_BASE + 0x0068)
/* RMT_STATUS_CH2 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The status for channel2*/
#define RMT_STATUS_CH2 0xFFFFFFFF
#define RMT_STATUS_CH2_M ((RMT_STATUS_CH2_V)<<(RMT_STATUS_CH2_S))
#define RMT_STATUS_CH2_V 0xFFFFFFFF
#define RMT_STATUS_CH2_S 0
#define RMT_CH3STATUS_REG (DR_REG_RMT_BASE + 0x006c)
/* RMT_STATUS_CH3 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The status for channel3*/
#define RMT_STATUS_CH3 0xFFFFFFFF
#define RMT_STATUS_CH3_M ((RMT_STATUS_CH3_V)<<(RMT_STATUS_CH3_S))
#define RMT_STATUS_CH3_V 0xFFFFFFFF
#define RMT_STATUS_CH3_S 0
#define RMT_CH4STATUS_REG (DR_REG_RMT_BASE + 0x0070)
/* RMT_STATUS_CH4 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The status for channel4*/
#define RMT_STATUS_CH4 0xFFFFFFFF
#define RMT_STATUS_CH4_M ((RMT_STATUS_CH4_V)<<(RMT_STATUS_CH4_S))
#define RMT_STATUS_CH4_V 0xFFFFFFFF
#define RMT_STATUS_CH4_S 0
#define RMT_CH5STATUS_REG (DR_REG_RMT_BASE + 0x0074)
/* RMT_STATUS_CH5 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The status for channel5*/
#define RMT_STATUS_CH5 0xFFFFFFFF
#define RMT_STATUS_CH5_M ((RMT_STATUS_CH5_V)<<(RMT_STATUS_CH5_S))
#define RMT_STATUS_CH5_V 0xFFFFFFFF
#define RMT_STATUS_CH5_S 0
#define RMT_CH6STATUS_REG (DR_REG_RMT_BASE + 0x0078)
/* RMT_STATUS_CH6 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The status for channel6*/
#define RMT_STATUS_CH6 0xFFFFFFFF
#define RMT_STATUS_CH6_M ((RMT_STATUS_CH6_V)<<(RMT_STATUS_CH6_S))
#define RMT_STATUS_CH6_V 0xFFFFFFFF
#define RMT_STATUS_CH6_S 0
#define RMT_CH7STATUS_REG (DR_REG_RMT_BASE + 0x007c)
/* RMT_STATUS_CH7 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The status for channel7*/
#define RMT_STATUS_CH7 0xFFFFFFFF
#define RMT_STATUS_CH7_M ((RMT_STATUS_CH7_V)<<(RMT_STATUS_CH7_S))
#define RMT_STATUS_CH7_V 0xFFFFFFFF
#define RMT_STATUS_CH7_S 0
#define RMT_CH0ADDR_REG (DR_REG_RMT_BASE + 0x0080)
/* RMT_APB_MEM_ADDR_CH0 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The ram relative address in channel0 by apb fifo access*/
#define RMT_APB_MEM_ADDR_CH0 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH0_M ((RMT_APB_MEM_ADDR_CH0_V)<<(RMT_APB_MEM_ADDR_CH0_S))
#define RMT_APB_MEM_ADDR_CH0_V 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH0_S 0
#define RMT_CH1ADDR_REG (DR_REG_RMT_BASE + 0x0084)
/* RMT_APB_MEM_ADDR_CH1 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The ram relative address in channel1 by apb fifo access*/
#define RMT_APB_MEM_ADDR_CH1 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH1_M ((RMT_APB_MEM_ADDR_CH1_V)<<(RMT_APB_MEM_ADDR_CH1_S))
#define RMT_APB_MEM_ADDR_CH1_V 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH1_S 0
#define RMT_CH2ADDR_REG (DR_REG_RMT_BASE + 0x0088)
/* RMT_APB_MEM_ADDR_CH2 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The ram relative address in channel2 by apb fifo access*/
#define RMT_APB_MEM_ADDR_CH2 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH2_M ((RMT_APB_MEM_ADDR_CH2_V)<<(RMT_APB_MEM_ADDR_CH2_S))
#define RMT_APB_MEM_ADDR_CH2_V 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH2_S 0
#define RMT_CH3ADDR_REG (DR_REG_RMT_BASE + 0x008c)
/* RMT_APB_MEM_ADDR_CH3 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The ram relative address in channel3 by apb fifo access*/
#define RMT_APB_MEM_ADDR_CH3 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH3_M ((RMT_APB_MEM_ADDR_CH3_V)<<(RMT_APB_MEM_ADDR_CH3_S))
#define RMT_APB_MEM_ADDR_CH3_V 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH3_S 0
#define RMT_CH4ADDR_REG (DR_REG_RMT_BASE + 0x0090)
/* RMT_APB_MEM_ADDR_CH4 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The ram relative address in channel4 by apb fifo access*/
#define RMT_APB_MEM_ADDR_CH4 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH4_M ((RMT_APB_MEM_ADDR_CH4_V)<<(RMT_APB_MEM_ADDR_CH4_S))
#define RMT_APB_MEM_ADDR_CH4_V 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH4_S 0
#define RMT_CH5ADDR_REG (DR_REG_RMT_BASE + 0x0094)
/* RMT_APB_MEM_ADDR_CH5 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The ram relative address in channel5 by apb fifo access*/
#define RMT_APB_MEM_ADDR_CH5 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH5_M ((RMT_APB_MEM_ADDR_CH5_V)<<(RMT_APB_MEM_ADDR_CH5_S))
#define RMT_APB_MEM_ADDR_CH5_V 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH5_S 0
#define RMT_CH6ADDR_REG (DR_REG_RMT_BASE + 0x0098)
/* RMT_APB_MEM_ADDR_CH6 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The ram relative address in channel6 by apb fifo access*/
#define RMT_APB_MEM_ADDR_CH6 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH6_M ((RMT_APB_MEM_ADDR_CH6_V)<<(RMT_APB_MEM_ADDR_CH6_S))
#define RMT_APB_MEM_ADDR_CH6_V 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH6_S 0
#define RMT_CH7ADDR_REG (DR_REG_RMT_BASE + 0x009c)
/* RMT_APB_MEM_ADDR_CH7 : RO ;bitpos:[31:0] ;default: 32'h0 ; */
/*description: The ram relative address in channel7 by apb fifo access*/
#define RMT_APB_MEM_ADDR_CH7 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH7_M ((RMT_APB_MEM_ADDR_CH7_V)<<(RMT_APB_MEM_ADDR_CH7_S))
#define RMT_APB_MEM_ADDR_CH7_V 0xFFFFFFFF
#define RMT_APB_MEM_ADDR_CH7_S 0
#define RMT_INT_RAW_REG (DR_REG_RMT_BASE + 0x00a0)
/* RMT_CH7_TX_THR_EVENT_INT_RAW : RO ;bitpos:[31] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 7 turns to high level when
transmitter in channle7 have send datas more than reg_rmt_tx_lim_ch7 after detecting this interrupt software can updata the old datas with new datas.*/
#define RMT_CH7_TX_THR_EVENT_INT_RAW (BIT(31))
#define RMT_CH7_TX_THR_EVENT_INT_RAW_M (BIT(31))
#define RMT_CH7_TX_THR_EVENT_INT_RAW_V 0x1
#define RMT_CH7_TX_THR_EVENT_INT_RAW_S 31
/* RMT_CH6_TX_THR_EVENT_INT_RAW : RO ;bitpos:[30] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 6 turns to high level when
transmitter in channle6 have send datas more than reg_rmt_tx_lim_ch6 after detecting this interrupt software can updata the old datas with new datas.*/
#define RMT_CH6_TX_THR_EVENT_INT_RAW (BIT(30))
#define RMT_CH6_TX_THR_EVENT_INT_RAW_M (BIT(30))
#define RMT_CH6_TX_THR_EVENT_INT_RAW_V 0x1
#define RMT_CH6_TX_THR_EVENT_INT_RAW_S 30
/* RMT_CH5_TX_THR_EVENT_INT_RAW : RO ;bitpos:[29] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 5 turns to high level when
transmitter in channle5 have send datas more than reg_rmt_tx_lim_ch5 after detecting this interrupt software can updata the old datas with new datas.*/
#define RMT_CH5_TX_THR_EVENT_INT_RAW (BIT(29))
#define RMT_CH5_TX_THR_EVENT_INT_RAW_M (BIT(29))
#define RMT_CH5_TX_THR_EVENT_INT_RAW_V 0x1
#define RMT_CH5_TX_THR_EVENT_INT_RAW_S 29
/* RMT_CH4_TX_THR_EVENT_INT_RAW : RO ;bitpos:[28] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 4 turns to high level when
transmitter in channle4 have send datas more than reg_rmt_tx_lim_ch4 after detecting this interrupt software can updata the old datas with new datas.*/
#define RMT_CH4_TX_THR_EVENT_INT_RAW (BIT(28))
#define RMT_CH4_TX_THR_EVENT_INT_RAW_M (BIT(28))
#define RMT_CH4_TX_THR_EVENT_INT_RAW_V 0x1
#define RMT_CH4_TX_THR_EVENT_INT_RAW_S 28
/* RMT_CH3_TX_THR_EVENT_INT_RAW : RO ;bitpos:[27] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 3 turns to high level when
transmitter in channle3 have send datas more than reg_rmt_tx_lim_ch3 after detecting this interrupt software can updata the old datas with new datas.*/
#define RMT_CH3_TX_THR_EVENT_INT_RAW (BIT(27))
#define RMT_CH3_TX_THR_EVENT_INT_RAW_M (BIT(27))
#define RMT_CH3_TX_THR_EVENT_INT_RAW_V 0x1
#define RMT_CH3_TX_THR_EVENT_INT_RAW_S 27
/* RMT_CH2_TX_THR_EVENT_INT_RAW : RO ;bitpos:[26] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 2 turns to high level when
transmitter in channle2 have send datas more than reg_rmt_tx_lim_ch2 after detecting this interrupt software can updata the old datas with new datas.*/
#define RMT_CH2_TX_THR_EVENT_INT_RAW (BIT(26))
#define RMT_CH2_TX_THR_EVENT_INT_RAW_M (BIT(26))
#define RMT_CH2_TX_THR_EVENT_INT_RAW_V 0x1
#define RMT_CH2_TX_THR_EVENT_INT_RAW_S 26
/* RMT_CH1_TX_THR_EVENT_INT_RAW : RO ;bitpos:[25] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 1 turns to high level when
transmitter in channle1 have send datas more than reg_rmt_tx_lim_ch1 after detecting this interrupt software can updata the old datas with new datas.*/
#define RMT_CH1_TX_THR_EVENT_INT_RAW (BIT(25))
#define RMT_CH1_TX_THR_EVENT_INT_RAW_M (BIT(25))
#define RMT_CH1_TX_THR_EVENT_INT_RAW_V 0x1
#define RMT_CH1_TX_THR_EVENT_INT_RAW_S 25
/* RMT_CH0_TX_THR_EVENT_INT_RAW : RO ;bitpos:[24] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 0 turns to high level when
transmitter in channle0 have send datas more than reg_rmt_tx_lim_ch0 after detecting this interrupt software can updata the old datas with new datas.*/
#define RMT_CH0_TX_THR_EVENT_INT_RAW (BIT(24))
#define RMT_CH0_TX_THR_EVENT_INT_RAW_M (BIT(24))
#define RMT_CH0_TX_THR_EVENT_INT_RAW_V 0x1
#define RMT_CH0_TX_THR_EVENT_INT_RAW_S 24
/* RMT_CH7_ERR_INT_RAW : RO ;bitpos:[23] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 7 turns to high level when
channle 7 detects some errors.*/
#define RMT_CH7_ERR_INT_RAW (BIT(23))
#define RMT_CH7_ERR_INT_RAW_M (BIT(23))
#define RMT_CH7_ERR_INT_RAW_V 0x1
#define RMT_CH7_ERR_INT_RAW_S 23
/* RMT_CH7_RX_END_INT_RAW : RO ;bitpos:[22] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 7 turns to high level when
the receive process is done.*/
#define RMT_CH7_RX_END_INT_RAW (BIT(22))
#define RMT_CH7_RX_END_INT_RAW_M (BIT(22))
#define RMT_CH7_RX_END_INT_RAW_V 0x1
#define RMT_CH7_RX_END_INT_RAW_S 22
/* RMT_CH7_TX_END_INT_RAW : RO ;bitpos:[21] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 7 turns to high level when
the transmit process is done.*/
#define RMT_CH7_TX_END_INT_RAW (BIT(21))
#define RMT_CH7_TX_END_INT_RAW_M (BIT(21))
#define RMT_CH7_TX_END_INT_RAW_V 0x1
#define RMT_CH7_TX_END_INT_RAW_S 21
/* RMT_CH6_ERR_INT_RAW : RO ;bitpos:[20] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 6 turns to high level when
channle 6 detects some errors.*/
#define RMT_CH6_ERR_INT_RAW (BIT(20))
#define RMT_CH6_ERR_INT_RAW_M (BIT(20))
#define RMT_CH6_ERR_INT_RAW_V 0x1
#define RMT_CH6_ERR_INT_RAW_S 20
/* RMT_CH6_RX_END_INT_RAW : RO ;bitpos:[19] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 6 turns to high level when
the receive process is done.*/
#define RMT_CH6_RX_END_INT_RAW (BIT(19))
#define RMT_CH6_RX_END_INT_RAW_M (BIT(19))
#define RMT_CH6_RX_END_INT_RAW_V 0x1
#define RMT_CH6_RX_END_INT_RAW_S 19
/* RMT_CH6_TX_END_INT_RAW : RO ;bitpos:[18] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 6 turns to high level when
the transmit process is done.*/
#define RMT_CH6_TX_END_INT_RAW (BIT(18))
#define RMT_CH6_TX_END_INT_RAW_M (BIT(18))
#define RMT_CH6_TX_END_INT_RAW_V 0x1
#define RMT_CH6_TX_END_INT_RAW_S 18
/* RMT_CH5_ERR_INT_RAW : RO ;bitpos:[17] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 5 turns to high level when
channle 5 detects some errors.*/
#define RMT_CH5_ERR_INT_RAW (BIT(17))
#define RMT_CH5_ERR_INT_RAW_M (BIT(17))
#define RMT_CH5_ERR_INT_RAW_V 0x1
#define RMT_CH5_ERR_INT_RAW_S 17
/* RMT_CH5_RX_END_INT_RAW : RO ;bitpos:[16] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 5 turns to high level when
the receive process is done.*/
#define RMT_CH5_RX_END_INT_RAW (BIT(16))
#define RMT_CH5_RX_END_INT_RAW_M (BIT(16))
#define RMT_CH5_RX_END_INT_RAW_V 0x1
#define RMT_CH5_RX_END_INT_RAW_S 16
/* RMT_CH5_TX_END_INT_RAW : RO ;bitpos:[15] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 5 turns to high level when
the transmit process is done.*/
#define RMT_CH5_TX_END_INT_RAW (BIT(15))
#define RMT_CH5_TX_END_INT_RAW_M (BIT(15))
#define RMT_CH5_TX_END_INT_RAW_V 0x1
#define RMT_CH5_TX_END_INT_RAW_S 15
/* RMT_CH4_ERR_INT_RAW : RO ;bitpos:[14] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 4 turns to high level when
channle 4 detects some errors.*/
#define RMT_CH4_ERR_INT_RAW (BIT(14))
#define RMT_CH4_ERR_INT_RAW_M (BIT(14))
#define RMT_CH4_ERR_INT_RAW_V 0x1
#define RMT_CH4_ERR_INT_RAW_S 14
/* RMT_CH4_RX_END_INT_RAW : RO ;bitpos:[13] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 4 turns to high level when
the receive process is done.*/
#define RMT_CH4_RX_END_INT_RAW (BIT(13))
#define RMT_CH4_RX_END_INT_RAW_M (BIT(13))
#define RMT_CH4_RX_END_INT_RAW_V 0x1
#define RMT_CH4_RX_END_INT_RAW_S 13
/* RMT_CH4_TX_END_INT_RAW : RO ;bitpos:[12] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 4 turns to high level when
the transmit process is done.*/
#define RMT_CH4_TX_END_INT_RAW (BIT(12))
#define RMT_CH4_TX_END_INT_RAW_M (BIT(12))
#define RMT_CH4_TX_END_INT_RAW_V 0x1
#define RMT_CH4_TX_END_INT_RAW_S 12
/* RMT_CH3_ERR_INT_RAW : RO ;bitpos:[11] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 3 turns to high level when
channle 3 detects some errors.*/
#define RMT_CH3_ERR_INT_RAW (BIT(11))
#define RMT_CH3_ERR_INT_RAW_M (BIT(11))
#define RMT_CH3_ERR_INT_RAW_V 0x1
#define RMT_CH3_ERR_INT_RAW_S 11
/* RMT_CH3_RX_END_INT_RAW : RO ;bitpos:[10] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 3 turns to high level when
the receive process is done.*/
#define RMT_CH3_RX_END_INT_RAW (BIT(10))
#define RMT_CH3_RX_END_INT_RAW_M (BIT(10))
#define RMT_CH3_RX_END_INT_RAW_V 0x1
#define RMT_CH3_RX_END_INT_RAW_S 10
/* RMT_CH3_TX_END_INT_RAW : RO ;bitpos:[9] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 3 turns to high level when
the transmit process is done.*/
#define RMT_CH3_TX_END_INT_RAW (BIT(9))
#define RMT_CH3_TX_END_INT_RAW_M (BIT(9))
#define RMT_CH3_TX_END_INT_RAW_V 0x1
#define RMT_CH3_TX_END_INT_RAW_S 9
/* RMT_CH2_ERR_INT_RAW : RO ;bitpos:[8] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 2 turns to high level when
channle 2 detects some errors.*/
#define RMT_CH2_ERR_INT_RAW (BIT(8))
#define RMT_CH2_ERR_INT_RAW_M (BIT(8))
#define RMT_CH2_ERR_INT_RAW_V 0x1
#define RMT_CH2_ERR_INT_RAW_S 8
/* RMT_CH2_RX_END_INT_RAW : RO ;bitpos:[7] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 2 turns to high level when
the receive process is done.*/
#define RMT_CH2_RX_END_INT_RAW (BIT(7))
#define RMT_CH2_RX_END_INT_RAW_M (BIT(7))
#define RMT_CH2_RX_END_INT_RAW_V 0x1
#define RMT_CH2_RX_END_INT_RAW_S 7
/* RMT_CH2_TX_END_INT_RAW : RO ;bitpos:[6] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 2 turns to high level when
the transmit process is done.*/
#define RMT_CH2_TX_END_INT_RAW (BIT(6))
#define RMT_CH2_TX_END_INT_RAW_M (BIT(6))
#define RMT_CH2_TX_END_INT_RAW_V 0x1
#define RMT_CH2_TX_END_INT_RAW_S 6
/* RMT_CH1_ERR_INT_RAW : RO ;bitpos:[5] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 1 turns to high level when
channle 1 detects some errors.*/
#define RMT_CH1_ERR_INT_RAW (BIT(5))
#define RMT_CH1_ERR_INT_RAW_M (BIT(5))
#define RMT_CH1_ERR_INT_RAW_V 0x1
#define RMT_CH1_ERR_INT_RAW_S 5
/* RMT_CH1_RX_END_INT_RAW : RO ;bitpos:[4] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 1 turns to high level when
the receive process is done.*/
#define RMT_CH1_RX_END_INT_RAW (BIT(4))
#define RMT_CH1_RX_END_INT_RAW_M (BIT(4))
#define RMT_CH1_RX_END_INT_RAW_V 0x1
#define RMT_CH1_RX_END_INT_RAW_S 4
/* RMT_CH1_TX_END_INT_RAW : RO ;bitpos:[3] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 1 turns to high level when
the transmit process is done.*/
#define RMT_CH1_TX_END_INT_RAW (BIT(3))
#define RMT_CH1_TX_END_INT_RAW_M (BIT(3))
#define RMT_CH1_TX_END_INT_RAW_V 0x1
#define RMT_CH1_TX_END_INT_RAW_S 3
/* RMT_CH0_ERR_INT_RAW : RO ;bitpos:[2] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 0 turns to high level when
channle 0 detects some errors.*/
#define RMT_CH0_ERR_INT_RAW (BIT(2))
#define RMT_CH0_ERR_INT_RAW_M (BIT(2))
#define RMT_CH0_ERR_INT_RAW_V 0x1
#define RMT_CH0_ERR_INT_RAW_S 2
/* RMT_CH0_RX_END_INT_RAW : RO ;bitpos:[1] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 0 turns to high level when
the receive process is done.*/
#define RMT_CH0_RX_END_INT_RAW (BIT(1))
#define RMT_CH0_RX_END_INT_RAW_M (BIT(1))
#define RMT_CH0_RX_END_INT_RAW_V 0x1
#define RMT_CH0_RX_END_INT_RAW_S 1
/* RMT_CH0_TX_END_INT_RAW : RO ;bitpos:[0] ;default: 1'b0 ; */
/*description: The interrupt raw bit for channel 0 turns to high level when
the transmit process is done.*/
#define RMT_CH0_TX_END_INT_RAW (BIT(0))
#define RMT_CH0_TX_END_INT_RAW_M (BIT(0))
#define RMT_CH0_TX_END_INT_RAW_V 0x1
#define RMT_CH0_TX_END_INT_RAW_S 0
#define RMT_INT_ST_REG (DR_REG_RMT_BASE + 0x00a4)
/* RMT_CH7_TX_THR_EVENT_INT_ST : RO ;bitpos:[31] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 7's rmt_ch7_tx_thr_event_int_raw
when mt_ch7_tx_thr_event_int_ena is set to 1.*/
#define RMT_CH7_TX_THR_EVENT_INT_ST (BIT(31))
#define RMT_CH7_TX_THR_EVENT_INT_ST_M (BIT(31))
#define RMT_CH7_TX_THR_EVENT_INT_ST_V 0x1
#define RMT_CH7_TX_THR_EVENT_INT_ST_S 31
/* RMT_CH6_TX_THR_EVENT_INT_ST : RO ;bitpos:[30] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 6's rmt_ch6_tx_thr_event_int_raw
when mt_ch6_tx_thr_event_int_ena is set to 1.*/
#define RMT_CH6_TX_THR_EVENT_INT_ST (BIT(30))
#define RMT_CH6_TX_THR_EVENT_INT_ST_M (BIT(30))
#define RMT_CH6_TX_THR_EVENT_INT_ST_V 0x1
#define RMT_CH6_TX_THR_EVENT_INT_ST_S 30
/* RMT_CH5_TX_THR_EVENT_INT_ST : RO ;bitpos:[29] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 5's rmt_ch5_tx_thr_event_int_raw
when mt_ch5_tx_thr_event_int_ena is set to 1.*/
#define RMT_CH5_TX_THR_EVENT_INT_ST (BIT(29))
#define RMT_CH5_TX_THR_EVENT_INT_ST_M (BIT(29))
#define RMT_CH5_TX_THR_EVENT_INT_ST_V 0x1
#define RMT_CH5_TX_THR_EVENT_INT_ST_S 29
/* RMT_CH4_TX_THR_EVENT_INT_ST : RO ;bitpos:[28] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 4's rmt_ch4_tx_thr_event_int_raw
when mt_ch4_tx_thr_event_int_ena is set to 1.*/
#define RMT_CH4_TX_THR_EVENT_INT_ST (BIT(28))
#define RMT_CH4_TX_THR_EVENT_INT_ST_M (BIT(28))
#define RMT_CH4_TX_THR_EVENT_INT_ST_V 0x1
#define RMT_CH4_TX_THR_EVENT_INT_ST_S 28
/* RMT_CH3_TX_THR_EVENT_INT_ST : RO ;bitpos:[27] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 3's rmt_ch3_tx_thr_event_int_raw
when mt_ch3_tx_thr_event_int_ena is set to 1.*/
#define RMT_CH3_TX_THR_EVENT_INT_ST (BIT(27))
#define RMT_CH3_TX_THR_EVENT_INT_ST_M (BIT(27))
#define RMT_CH3_TX_THR_EVENT_INT_ST_V 0x1
#define RMT_CH3_TX_THR_EVENT_INT_ST_S 27
/* RMT_CH2_TX_THR_EVENT_INT_ST : RO ;bitpos:[26] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 2's rmt_ch2_tx_thr_event_int_raw
when mt_ch2_tx_thr_event_int_ena is set to 1.*/
#define RMT_CH2_TX_THR_EVENT_INT_ST (BIT(26))
#define RMT_CH2_TX_THR_EVENT_INT_ST_M (BIT(26))
#define RMT_CH2_TX_THR_EVENT_INT_ST_V 0x1
#define RMT_CH2_TX_THR_EVENT_INT_ST_S 26
/* RMT_CH1_TX_THR_EVENT_INT_ST : RO ;bitpos:[25] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 1's rmt_ch1_tx_thr_event_int_raw
when mt_ch1_tx_thr_event_int_ena is set to 1.*/
#define RMT_CH1_TX_THR_EVENT_INT_ST (BIT(25))
#define RMT_CH1_TX_THR_EVENT_INT_ST_M (BIT(25))
#define RMT_CH1_TX_THR_EVENT_INT_ST_V 0x1
#define RMT_CH1_TX_THR_EVENT_INT_ST_S 25
/* RMT_CH0_TX_THR_EVENT_INT_ST : RO ;bitpos:[24] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 0's rmt_ch0_tx_thr_event_int_raw
when mt_ch0_tx_thr_event_int_ena is set to 1.*/
#define RMT_CH0_TX_THR_EVENT_INT_ST (BIT(24))
#define RMT_CH0_TX_THR_EVENT_INT_ST_M (BIT(24))
#define RMT_CH0_TX_THR_EVENT_INT_ST_V 0x1
#define RMT_CH0_TX_THR_EVENT_INT_ST_S 24
/* RMT_CH7_ERR_INT_ST : RO ;bitpos:[23] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 7's rmt_ch7_err_int_raw
when rmt_ch7_err_int_ena is set to 1.*/
#define RMT_CH7_ERR_INT_ST (BIT(23))
#define RMT_CH7_ERR_INT_ST_M (BIT(23))
#define RMT_CH7_ERR_INT_ST_V 0x1
#define RMT_CH7_ERR_INT_ST_S 23
/* RMT_CH7_RX_END_INT_ST : RO ;bitpos:[22] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 7's rmt_ch7_rx_end_int_raw
when rmt_ch7_rx_end_int_ena is set to 1.*/
#define RMT_CH7_RX_END_INT_ST (BIT(22))
#define RMT_CH7_RX_END_INT_ST_M (BIT(22))
#define RMT_CH7_RX_END_INT_ST_V 0x1
#define RMT_CH7_RX_END_INT_ST_S 22
/* RMT_CH7_TX_END_INT_ST : RO ;bitpos:[21] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 7's mt_ch7_tx_end_int_raw
when mt_ch7_tx_end_int_ena is set to 1.*/
#define RMT_CH7_TX_END_INT_ST (BIT(21))
#define RMT_CH7_TX_END_INT_ST_M (BIT(21))
#define RMT_CH7_TX_END_INT_ST_V 0x1
#define RMT_CH7_TX_END_INT_ST_S 21
/* RMT_CH6_ERR_INT_ST : RO ;bitpos:[20] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 6's rmt_ch6_err_int_raw
when rmt_ch6_err_int_ena is set to 1.*/
#define RMT_CH6_ERR_INT_ST (BIT(20))
#define RMT_CH6_ERR_INT_ST_M (BIT(20))
#define RMT_CH6_ERR_INT_ST_V 0x1
#define RMT_CH6_ERR_INT_ST_S 20
/* RMT_CH6_RX_END_INT_ST : RO ;bitpos:[19] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 6's rmt_ch6_rx_end_int_raw
when rmt_ch6_rx_end_int_ena is set to 1.*/
#define RMT_CH6_RX_END_INT_ST (BIT(19))
#define RMT_CH6_RX_END_INT_ST_M (BIT(19))
#define RMT_CH6_RX_END_INT_ST_V 0x1
#define RMT_CH6_RX_END_INT_ST_S 19
/* RMT_CH6_TX_END_INT_ST : RO ;bitpos:[18] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 6's mt_ch6_tx_end_int_raw
when mt_ch6_tx_end_int_ena is set to 1.*/
#define RMT_CH6_TX_END_INT_ST (BIT(18))
#define RMT_CH6_TX_END_INT_ST_M (BIT(18))
#define RMT_CH6_TX_END_INT_ST_V 0x1
#define RMT_CH6_TX_END_INT_ST_S 18
/* RMT_CH5_ERR_INT_ST : RO ;bitpos:[17] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 5's rmt_ch5_err_int_raw
when rmt_ch5_err_int_ena is set to 1.*/
#define RMT_CH5_ERR_INT_ST (BIT(17))
#define RMT_CH5_ERR_INT_ST_M (BIT(17))
#define RMT_CH5_ERR_INT_ST_V 0x1
#define RMT_CH5_ERR_INT_ST_S 17
/* RMT_CH5_RX_END_INT_ST : RO ;bitpos:[16] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 5's rmt_ch5_rx_end_int_raw
when rmt_ch5_rx_end_int_ena is set to 1.*/
#define RMT_CH5_RX_END_INT_ST (BIT(16))
#define RMT_CH5_RX_END_INT_ST_M (BIT(16))
#define RMT_CH5_RX_END_INT_ST_V 0x1
#define RMT_CH5_RX_END_INT_ST_S 16
/* RMT_CH5_TX_END_INT_ST : RO ;bitpos:[15] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 5's mt_ch5_tx_end_int_raw
when mt_ch5_tx_end_int_ena is set to 1.*/
#define RMT_CH5_TX_END_INT_ST (BIT(15))
#define RMT_CH5_TX_END_INT_ST_M (BIT(15))
#define RMT_CH5_TX_END_INT_ST_V 0x1
#define RMT_CH5_TX_END_INT_ST_S 15
/* RMT_CH4_ERR_INT_ST : RO ;bitpos:[14] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 4's rmt_ch4_err_int_raw
when rmt_ch4_err_int_ena is set to 1.*/
#define RMT_CH4_ERR_INT_ST (BIT(14))
#define RMT_CH4_ERR_INT_ST_M (BIT(14))
#define RMT_CH4_ERR_INT_ST_V 0x1
#define RMT_CH4_ERR_INT_ST_S 14
/* RMT_CH4_RX_END_INT_ST : RO ;bitpos:[13] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 4's rmt_ch4_rx_end_int_raw
when rmt_ch4_rx_end_int_ena is set to 1.*/
#define RMT_CH4_RX_END_INT_ST (BIT(13))
#define RMT_CH4_RX_END_INT_ST_M (BIT(13))
#define RMT_CH4_RX_END_INT_ST_V 0x1
#define RMT_CH4_RX_END_INT_ST_S 13
/* RMT_CH4_TX_END_INT_ST : RO ;bitpos:[12] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 4's mt_ch4_tx_end_int_raw
when mt_ch4_tx_end_int_ena is set to 1.*/
#define RMT_CH4_TX_END_INT_ST (BIT(12))
#define RMT_CH4_TX_END_INT_ST_M (BIT(12))
#define RMT_CH4_TX_END_INT_ST_V 0x1
#define RMT_CH4_TX_END_INT_ST_S 12
/* RMT_CH3_ERR_INT_ST : RO ;bitpos:[11] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 3's rmt_ch3_err_int_raw
when rmt_ch3_err_int_ena is set to 1.*/
#define RMT_CH3_ERR_INT_ST (BIT(11))
#define RMT_CH3_ERR_INT_ST_M (BIT(11))
#define RMT_CH3_ERR_INT_ST_V 0x1
#define RMT_CH3_ERR_INT_ST_S 11
/* RMT_CH3_RX_END_INT_ST : RO ;bitpos:[10] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 3's rmt_ch3_rx_end_int_raw
when rmt_ch3_rx_end_int_ena is set to 1.*/
#define RMT_CH3_RX_END_INT_ST (BIT(10))
#define RMT_CH3_RX_END_INT_ST_M (BIT(10))
#define RMT_CH3_RX_END_INT_ST_V 0x1
#define RMT_CH3_RX_END_INT_ST_S 10
/* RMT_CH3_TX_END_INT_ST : RO ;bitpos:[9] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 3's mt_ch3_tx_end_int_raw
when mt_ch3_tx_end_int_ena is set to 1.*/
#define RMT_CH3_TX_END_INT_ST (BIT(9))
#define RMT_CH3_TX_END_INT_ST_M (BIT(9))
#define RMT_CH3_TX_END_INT_ST_V 0x1
#define RMT_CH3_TX_END_INT_ST_S 9
/* RMT_CH2_ERR_INT_ST : RO ;bitpos:[8] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 2's rmt_ch2_err_int_raw
when rmt_ch2_err_int_ena is set to 1.*/
#define RMT_CH2_ERR_INT_ST (BIT(8))
#define RMT_CH2_ERR_INT_ST_M (BIT(8))
#define RMT_CH2_ERR_INT_ST_V 0x1
#define RMT_CH2_ERR_INT_ST_S 8
/* RMT_CH2_RX_END_INT_ST : RO ;bitpos:[7] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 2's rmt_ch2_rx_end_int_raw
when rmt_ch2_rx_end_int_ena is set to 1.*/
#define RMT_CH2_RX_END_INT_ST (BIT(7))
#define RMT_CH2_RX_END_INT_ST_M (BIT(7))
#define RMT_CH2_RX_END_INT_ST_V 0x1
#define RMT_CH2_RX_END_INT_ST_S 7
/* RMT_CH2_TX_END_INT_ST : RO ;bitpos:[6] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 2's mt_ch2_tx_end_int_raw
when mt_ch2_tx_end_int_ena is set to 1.*/
#define RMT_CH2_TX_END_INT_ST (BIT(6))
#define RMT_CH2_TX_END_INT_ST_M (BIT(6))
#define RMT_CH2_TX_END_INT_ST_V 0x1
#define RMT_CH2_TX_END_INT_ST_S 6
/* RMT_CH1_ERR_INT_ST : RO ;bitpos:[5] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 1's rmt_ch1_err_int_raw
when rmt_ch1_err_int_ena is set to 1.*/
#define RMT_CH1_ERR_INT_ST (BIT(5))
#define RMT_CH1_ERR_INT_ST_M (BIT(5))
#define RMT_CH1_ERR_INT_ST_V 0x1
#define RMT_CH1_ERR_INT_ST_S 5
/* RMT_CH1_RX_END_INT_ST : RO ;bitpos:[4] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 1's rmt_ch1_rx_end_int_raw
when rmt_ch1_rx_end_int_ena is set to 1.*/
#define RMT_CH1_RX_END_INT_ST (BIT(4))
#define RMT_CH1_RX_END_INT_ST_M (BIT(4))
#define RMT_CH1_RX_END_INT_ST_V 0x1
#define RMT_CH1_RX_END_INT_ST_S 4
/* RMT_CH1_TX_END_INT_ST : RO ;bitpos:[3] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 1's mt_ch1_tx_end_int_raw
when mt_ch1_tx_end_int_ena is set to 1.*/
#define RMT_CH1_TX_END_INT_ST (BIT(3))
#define RMT_CH1_TX_END_INT_ST_M (BIT(3))
#define RMT_CH1_TX_END_INT_ST_V 0x1
#define RMT_CH1_TX_END_INT_ST_S 3
/* RMT_CH0_ERR_INT_ST : RO ;bitpos:[2] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 0's rmt_ch0_err_int_raw
when rmt_ch0_err_int_ena is set to 0.*/
#define RMT_CH0_ERR_INT_ST (BIT(2))
#define RMT_CH0_ERR_INT_ST_M (BIT(2))
#define RMT_CH0_ERR_INT_ST_V 0x1
#define RMT_CH0_ERR_INT_ST_S 2
/* RMT_CH0_RX_END_INT_ST : RO ;bitpos:[1] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 0's rmt_ch0_rx_end_int_raw
when rmt_ch0_rx_end_int_ena is set to 0.*/
#define RMT_CH0_RX_END_INT_ST (BIT(1))
#define RMT_CH0_RX_END_INT_ST_M (BIT(1))
#define RMT_CH0_RX_END_INT_ST_V 0x1
#define RMT_CH0_RX_END_INT_ST_S 1
/* RMT_CH0_TX_END_INT_ST : RO ;bitpos:[0] ;default: 1'b0 ; */
/*description: The interrupt state bit for channel 0's mt_ch0_tx_end_int_raw
when mt_ch0_tx_end_int_ena is set to 0.*/
#define RMT_CH0_TX_END_INT_ST (BIT(0))
#define RMT_CH0_TX_END_INT_ST_M (BIT(0))
#define RMT_CH0_TX_END_INT_ST_V 0x1
#define RMT_CH0_TX_END_INT_ST_S 0
#define RMT_INT_ENA_REG (DR_REG_RMT_BASE + 0x00a8)
/* RMT_CH7_TX_THR_EVENT_INT_ENA : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch7_tx_thr_event_int_st.*/
#define RMT_CH7_TX_THR_EVENT_INT_ENA (BIT(31))
#define RMT_CH7_TX_THR_EVENT_INT_ENA_M (BIT(31))
#define RMT_CH7_TX_THR_EVENT_INT_ENA_V 0x1
#define RMT_CH7_TX_THR_EVENT_INT_ENA_S 31
/* RMT_CH6_TX_THR_EVENT_INT_ENA : R/W ;bitpos:[30] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch6_tx_thr_event_int_st.*/
#define RMT_CH6_TX_THR_EVENT_INT_ENA (BIT(30))
#define RMT_CH6_TX_THR_EVENT_INT_ENA_M (BIT(30))
#define RMT_CH6_TX_THR_EVENT_INT_ENA_V 0x1
#define RMT_CH6_TX_THR_EVENT_INT_ENA_S 30
/* RMT_CH5_TX_THR_EVENT_INT_ENA : R/W ;bitpos:[29] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch5_tx_thr_event_int_st.*/
#define RMT_CH5_TX_THR_EVENT_INT_ENA (BIT(29))
#define RMT_CH5_TX_THR_EVENT_INT_ENA_M (BIT(29))
#define RMT_CH5_TX_THR_EVENT_INT_ENA_V 0x1
#define RMT_CH5_TX_THR_EVENT_INT_ENA_S 29
/* RMT_CH4_TX_THR_EVENT_INT_ENA : R/W ;bitpos:[28] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch4_tx_thr_event_int_st.*/
#define RMT_CH4_TX_THR_EVENT_INT_ENA (BIT(28))
#define RMT_CH4_TX_THR_EVENT_INT_ENA_M (BIT(28))
#define RMT_CH4_TX_THR_EVENT_INT_ENA_V 0x1
#define RMT_CH4_TX_THR_EVENT_INT_ENA_S 28
/* RMT_CH3_TX_THR_EVENT_INT_ENA : R/W ;bitpos:[27] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch3_tx_thr_event_int_st.*/
#define RMT_CH3_TX_THR_EVENT_INT_ENA (BIT(27))
#define RMT_CH3_TX_THR_EVENT_INT_ENA_M (BIT(27))
#define RMT_CH3_TX_THR_EVENT_INT_ENA_V 0x1
#define RMT_CH3_TX_THR_EVENT_INT_ENA_S 27
/* RMT_CH2_TX_THR_EVENT_INT_ENA : R/W ;bitpos:[26] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch2_tx_thr_event_int_st.*/
#define RMT_CH2_TX_THR_EVENT_INT_ENA (BIT(26))
#define RMT_CH2_TX_THR_EVENT_INT_ENA_M (BIT(26))
#define RMT_CH2_TX_THR_EVENT_INT_ENA_V 0x1
#define RMT_CH2_TX_THR_EVENT_INT_ENA_S 26
/* RMT_CH1_TX_THR_EVENT_INT_ENA : R/W ;bitpos:[25] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch1_tx_thr_event_int_st.*/
#define RMT_CH1_TX_THR_EVENT_INT_ENA (BIT(25))
#define RMT_CH1_TX_THR_EVENT_INT_ENA_M (BIT(25))
#define RMT_CH1_TX_THR_EVENT_INT_ENA_V 0x1
#define RMT_CH1_TX_THR_EVENT_INT_ENA_S 25
/* RMT_CH0_TX_THR_EVENT_INT_ENA : R/W ;bitpos:[24] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch0_tx_thr_event_int_st.*/
#define RMT_CH0_TX_THR_EVENT_INT_ENA (BIT(24))
#define RMT_CH0_TX_THR_EVENT_INT_ENA_M (BIT(24))
#define RMT_CH0_TX_THR_EVENT_INT_ENA_V 0x1
#define RMT_CH0_TX_THR_EVENT_INT_ENA_S 24
/* RMT_CH7_ERR_INT_ENA : R/W ;bitpos:[23] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch7_err_int_st.*/
#define RMT_CH7_ERR_INT_ENA (BIT(23))
#define RMT_CH7_ERR_INT_ENA_M (BIT(23))
#define RMT_CH7_ERR_INT_ENA_V 0x1
#define RMT_CH7_ERR_INT_ENA_S 23
/* RMT_CH7_RX_END_INT_ENA : R/W ;bitpos:[22] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch7_rx_end_int_st.*/
#define RMT_CH7_RX_END_INT_ENA (BIT(22))
#define RMT_CH7_RX_END_INT_ENA_M (BIT(22))
#define RMT_CH7_RX_END_INT_ENA_V 0x1
#define RMT_CH7_RX_END_INT_ENA_S 22
/* RMT_CH7_TX_END_INT_ENA : R/W ;bitpos:[21] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch7_tx_end_int_st.*/
#define RMT_CH7_TX_END_INT_ENA (BIT(21))
#define RMT_CH7_TX_END_INT_ENA_M (BIT(21))
#define RMT_CH7_TX_END_INT_ENA_V 0x1
#define RMT_CH7_TX_END_INT_ENA_S 21
/* RMT_CH6_ERR_INT_ENA : R/W ;bitpos:[20] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch6_err_int_st.*/
#define RMT_CH6_ERR_INT_ENA (BIT(20))
#define RMT_CH6_ERR_INT_ENA_M (BIT(20))
#define RMT_CH6_ERR_INT_ENA_V 0x1
#define RMT_CH6_ERR_INT_ENA_S 20
/* RMT_CH6_RX_END_INT_ENA : R/W ;bitpos:[19] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch6_rx_end_int_st.*/
#define RMT_CH6_RX_END_INT_ENA (BIT(19))
#define RMT_CH6_RX_END_INT_ENA_M (BIT(19))
#define RMT_CH6_RX_END_INT_ENA_V 0x1
#define RMT_CH6_RX_END_INT_ENA_S 19
/* RMT_CH6_TX_END_INT_ENA : R/W ;bitpos:[18] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch6_tx_end_int_st.*/
#define RMT_CH6_TX_END_INT_ENA (BIT(18))
#define RMT_CH6_TX_END_INT_ENA_M (BIT(18))
#define RMT_CH6_TX_END_INT_ENA_V 0x1
#define RMT_CH6_TX_END_INT_ENA_S 18
/* RMT_CH5_ERR_INT_ENA : R/W ;bitpos:[17] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch5_err_int_st.*/
#define RMT_CH5_ERR_INT_ENA (BIT(17))
#define RMT_CH5_ERR_INT_ENA_M (BIT(17))
#define RMT_CH5_ERR_INT_ENA_V 0x1
#define RMT_CH5_ERR_INT_ENA_S 17
/* RMT_CH5_RX_END_INT_ENA : R/W ;bitpos:[16] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch5_rx_end_int_st.*/
#define RMT_CH5_RX_END_INT_ENA (BIT(16))
#define RMT_CH5_RX_END_INT_ENA_M (BIT(16))
#define RMT_CH5_RX_END_INT_ENA_V 0x1
#define RMT_CH5_RX_END_INT_ENA_S 16
/* RMT_CH5_TX_END_INT_ENA : R/W ;bitpos:[15] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch5_tx_end_int_st.*/
#define RMT_CH5_TX_END_INT_ENA (BIT(15))
#define RMT_CH5_TX_END_INT_ENA_M (BIT(15))
#define RMT_CH5_TX_END_INT_ENA_V 0x1
#define RMT_CH5_TX_END_INT_ENA_S 15
/* RMT_CH4_ERR_INT_ENA : R/W ;bitpos:[14] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch4_err_int_st.*/
#define RMT_CH4_ERR_INT_ENA (BIT(14))
#define RMT_CH4_ERR_INT_ENA_M (BIT(14))
#define RMT_CH4_ERR_INT_ENA_V 0x1
#define RMT_CH4_ERR_INT_ENA_S 14
/* RMT_CH4_RX_END_INT_ENA : R/W ;bitpos:[13] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch4_rx_end_int_st.*/
#define RMT_CH4_RX_END_INT_ENA (BIT(13))
#define RMT_CH4_RX_END_INT_ENA_M (BIT(13))
#define RMT_CH4_RX_END_INT_ENA_V 0x1
#define RMT_CH4_RX_END_INT_ENA_S 13
/* RMT_CH4_TX_END_INT_ENA : R/W ;bitpos:[12] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch4_tx_end_int_st.*/
#define RMT_CH4_TX_END_INT_ENA (BIT(12))
#define RMT_CH4_TX_END_INT_ENA_M (BIT(12))
#define RMT_CH4_TX_END_INT_ENA_V 0x1
#define RMT_CH4_TX_END_INT_ENA_S 12
/* RMT_CH3_ERR_INT_ENA : R/W ;bitpos:[11] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch3_err_int_st.*/
#define RMT_CH3_ERR_INT_ENA (BIT(11))
#define RMT_CH3_ERR_INT_ENA_M (BIT(11))
#define RMT_CH3_ERR_INT_ENA_V 0x1
#define RMT_CH3_ERR_INT_ENA_S 11
/* RMT_CH3_RX_END_INT_ENA : R/W ;bitpos:[10] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch3_rx_end_int_st.*/
#define RMT_CH3_RX_END_INT_ENA (BIT(10))
#define RMT_CH3_RX_END_INT_ENA_M (BIT(10))
#define RMT_CH3_RX_END_INT_ENA_V 0x1
#define RMT_CH3_RX_END_INT_ENA_S 10
/* RMT_CH3_TX_END_INT_ENA : R/W ;bitpos:[9] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch3_tx_end_int_st.*/
#define RMT_CH3_TX_END_INT_ENA (BIT(9))
#define RMT_CH3_TX_END_INT_ENA_M (BIT(9))
#define RMT_CH3_TX_END_INT_ENA_V 0x1
#define RMT_CH3_TX_END_INT_ENA_S 9
/* RMT_CH2_ERR_INT_ENA : R/W ;bitpos:[8] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch2_err_int_st.*/
#define RMT_CH2_ERR_INT_ENA (BIT(8))
#define RMT_CH2_ERR_INT_ENA_M (BIT(8))
#define RMT_CH2_ERR_INT_ENA_V 0x1
#define RMT_CH2_ERR_INT_ENA_S 8
/* RMT_CH2_RX_END_INT_ENA : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch2_rx_end_int_st.*/
#define RMT_CH2_RX_END_INT_ENA (BIT(7))
#define RMT_CH2_RX_END_INT_ENA_M (BIT(7))
#define RMT_CH2_RX_END_INT_ENA_V 0x1
#define RMT_CH2_RX_END_INT_ENA_S 7
/* RMT_CH2_TX_END_INT_ENA : R/W ;bitpos:[6] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch2_tx_end_int_st.*/
#define RMT_CH2_TX_END_INT_ENA (BIT(6))
#define RMT_CH2_TX_END_INT_ENA_M (BIT(6))
#define RMT_CH2_TX_END_INT_ENA_V 0x1
#define RMT_CH2_TX_END_INT_ENA_S 6
/* RMT_CH1_ERR_INT_ENA : R/W ;bitpos:[5] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch1_err_int_st.*/
#define RMT_CH1_ERR_INT_ENA (BIT(5))
#define RMT_CH1_ERR_INT_ENA_M (BIT(5))
#define RMT_CH1_ERR_INT_ENA_V 0x1
#define RMT_CH1_ERR_INT_ENA_S 5
/* RMT_CH1_RX_END_INT_ENA : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch1_rx_end_int_st.*/
#define RMT_CH1_RX_END_INT_ENA (BIT(4))
#define RMT_CH1_RX_END_INT_ENA_M (BIT(4))
#define RMT_CH1_RX_END_INT_ENA_V 0x1
#define RMT_CH1_RX_END_INT_ENA_S 4
/* RMT_CH1_TX_END_INT_ENA : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch1_tx_end_int_st.*/
#define RMT_CH1_TX_END_INT_ENA (BIT(3))
#define RMT_CH1_TX_END_INT_ENA_M (BIT(3))
#define RMT_CH1_TX_END_INT_ENA_V 0x1
#define RMT_CH1_TX_END_INT_ENA_S 3
/* RMT_CH0_ERR_INT_ENA : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch0_err_int_st.*/
#define RMT_CH0_ERR_INT_ENA (BIT(2))
#define RMT_CH0_ERR_INT_ENA_M (BIT(2))
#define RMT_CH0_ERR_INT_ENA_V 0x1
#define RMT_CH0_ERR_INT_ENA_S 2
/* RMT_CH0_RX_END_INT_ENA : R/W ;bitpos:[1] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch0_rx_end_int_st.*/
#define RMT_CH0_RX_END_INT_ENA (BIT(1))
#define RMT_CH0_RX_END_INT_ENA_M (BIT(1))
#define RMT_CH0_RX_END_INT_ENA_V 0x1
#define RMT_CH0_RX_END_INT_ENA_S 1
/* RMT_CH0_TX_END_INT_ENA : R/W ;bitpos:[0] ;default: 1'b0 ; */
/*description: Set this bit to enable rmt_ch0_tx_end_int_st.*/
#define RMT_CH0_TX_END_INT_ENA (BIT(0))
#define RMT_CH0_TX_END_INT_ENA_M (BIT(0))
#define RMT_CH0_TX_END_INT_ENA_V 0x1
#define RMT_CH0_TX_END_INT_ENA_S 0
#define RMT_INT_CLR_REG (DR_REG_RMT_BASE + 0x00ac)
/* RMT_CH7_TX_THR_EVENT_INT_CLR : WO ;bitpos:[31] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch7_tx_thr_event_int_raw interrupt.*/
#define RMT_CH7_TX_THR_EVENT_INT_CLR (BIT(31))
#define RMT_CH7_TX_THR_EVENT_INT_CLR_M (BIT(31))
#define RMT_CH7_TX_THR_EVENT_INT_CLR_V 0x1
#define RMT_CH7_TX_THR_EVENT_INT_CLR_S 31
/* RMT_CH6_TX_THR_EVENT_INT_CLR : WO ;bitpos:[30] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch6_tx_thr_event_int_raw interrupt.*/
#define RMT_CH6_TX_THR_EVENT_INT_CLR (BIT(30))
#define RMT_CH6_TX_THR_EVENT_INT_CLR_M (BIT(30))
#define RMT_CH6_TX_THR_EVENT_INT_CLR_V 0x1
#define RMT_CH6_TX_THR_EVENT_INT_CLR_S 30
/* RMT_CH5_TX_THR_EVENT_INT_CLR : WO ;bitpos:[29] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch5_tx_thr_event_int_raw interrupt.*/
#define RMT_CH5_TX_THR_EVENT_INT_CLR (BIT(29))
#define RMT_CH5_TX_THR_EVENT_INT_CLR_M (BIT(29))
#define RMT_CH5_TX_THR_EVENT_INT_CLR_V 0x1
#define RMT_CH5_TX_THR_EVENT_INT_CLR_S 29
/* RMT_CH4_TX_THR_EVENT_INT_CLR : WO ;bitpos:[28] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch4_tx_thr_event_int_raw interrupt.*/
#define RMT_CH4_TX_THR_EVENT_INT_CLR (BIT(28))
#define RMT_CH4_TX_THR_EVENT_INT_CLR_M (BIT(28))
#define RMT_CH4_TX_THR_EVENT_INT_CLR_V 0x1
#define RMT_CH4_TX_THR_EVENT_INT_CLR_S 28
/* RMT_CH3_TX_THR_EVENT_INT_CLR : WO ;bitpos:[27] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch3_tx_thr_event_int_raw interrupt.*/
#define RMT_CH3_TX_THR_EVENT_INT_CLR (BIT(27))
#define RMT_CH3_TX_THR_EVENT_INT_CLR_M (BIT(27))
#define RMT_CH3_TX_THR_EVENT_INT_CLR_V 0x1
#define RMT_CH3_TX_THR_EVENT_INT_CLR_S 27
/* RMT_CH2_TX_THR_EVENT_INT_CLR : WO ;bitpos:[26] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch2_tx_thr_event_int_raw interrupt.*/
#define RMT_CH2_TX_THR_EVENT_INT_CLR (BIT(26))
#define RMT_CH2_TX_THR_EVENT_INT_CLR_M (BIT(26))
#define RMT_CH2_TX_THR_EVENT_INT_CLR_V 0x1
#define RMT_CH2_TX_THR_EVENT_INT_CLR_S 26
/* RMT_CH1_TX_THR_EVENT_INT_CLR : WO ;bitpos:[25] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch1_tx_thr_event_int_raw interrupt.*/
#define RMT_CH1_TX_THR_EVENT_INT_CLR (BIT(25))
#define RMT_CH1_TX_THR_EVENT_INT_CLR_M (BIT(25))
#define RMT_CH1_TX_THR_EVENT_INT_CLR_V 0x1
#define RMT_CH1_TX_THR_EVENT_INT_CLR_S 25
/* RMT_CH0_TX_THR_EVENT_INT_CLR : WO ;bitpos:[24] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch0_tx_thr_event_int_raw interrupt.*/
#define RMT_CH0_TX_THR_EVENT_INT_CLR (BIT(24))
#define RMT_CH0_TX_THR_EVENT_INT_CLR_M (BIT(24))
#define RMT_CH0_TX_THR_EVENT_INT_CLR_V 0x1
#define RMT_CH0_TX_THR_EVENT_INT_CLR_S 24
/* RMT_CH7_ERR_INT_CLR : WO ;bitpos:[23] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch7_err_int_raw.*/
#define RMT_CH7_ERR_INT_CLR (BIT(23))
#define RMT_CH7_ERR_INT_CLR_M (BIT(23))
#define RMT_CH7_ERR_INT_CLR_V 0x1
#define RMT_CH7_ERR_INT_CLR_S 23
/* RMT_CH7_RX_END_INT_CLR : WO ;bitpos:[22] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch7_tx_end_int_raw.*/
#define RMT_CH7_RX_END_INT_CLR (BIT(22))
#define RMT_CH7_RX_END_INT_CLR_M (BIT(22))
#define RMT_CH7_RX_END_INT_CLR_V 0x1
#define RMT_CH7_RX_END_INT_CLR_S 22
/* RMT_CH7_TX_END_INT_CLR : WO ;bitpos:[21] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch7_rx_end_int_raw..*/
#define RMT_CH7_TX_END_INT_CLR (BIT(21))
#define RMT_CH7_TX_END_INT_CLR_M (BIT(21))
#define RMT_CH7_TX_END_INT_CLR_V 0x1
#define RMT_CH7_TX_END_INT_CLR_S 21
/* RMT_CH6_ERR_INT_CLR : WO ;bitpos:[20] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch6_err_int_raw.*/
#define RMT_CH6_ERR_INT_CLR (BIT(20))
#define RMT_CH6_ERR_INT_CLR_M (BIT(20))
#define RMT_CH6_ERR_INT_CLR_V 0x1
#define RMT_CH6_ERR_INT_CLR_S 20
/* RMT_CH6_RX_END_INT_CLR : WO ;bitpos:[19] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch6_tx_end_int_raw.*/
#define RMT_CH6_RX_END_INT_CLR (BIT(19))
#define RMT_CH6_RX_END_INT_CLR_M (BIT(19))
#define RMT_CH6_RX_END_INT_CLR_V 0x1
#define RMT_CH6_RX_END_INT_CLR_S 19
/* RMT_CH6_TX_END_INT_CLR : WO ;bitpos:[18] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch6_rx_end_int_raw..*/
#define RMT_CH6_TX_END_INT_CLR (BIT(18))
#define RMT_CH6_TX_END_INT_CLR_M (BIT(18))
#define RMT_CH6_TX_END_INT_CLR_V 0x1
#define RMT_CH6_TX_END_INT_CLR_S 18
/* RMT_CH5_ERR_INT_CLR : WO ;bitpos:[17] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch5_err_int_raw.*/
#define RMT_CH5_ERR_INT_CLR (BIT(17))
#define RMT_CH5_ERR_INT_CLR_M (BIT(17))
#define RMT_CH5_ERR_INT_CLR_V 0x1
#define RMT_CH5_ERR_INT_CLR_S 17
/* RMT_CH5_RX_END_INT_CLR : WO ;bitpos:[16] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch5_tx_end_int_raw.*/
#define RMT_CH5_RX_END_INT_CLR (BIT(16))
#define RMT_CH5_RX_END_INT_CLR_M (BIT(16))
#define RMT_CH5_RX_END_INT_CLR_V 0x1
#define RMT_CH5_RX_END_INT_CLR_S 16
/* RMT_CH5_TX_END_INT_CLR : WO ;bitpos:[15] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch5_rx_end_int_raw..*/
#define RMT_CH5_TX_END_INT_CLR (BIT(15))
#define RMT_CH5_TX_END_INT_CLR_M (BIT(15))
#define RMT_CH5_TX_END_INT_CLR_V 0x1
#define RMT_CH5_TX_END_INT_CLR_S 15
/* RMT_CH4_ERR_INT_CLR : WO ;bitpos:[14] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch4_err_int_raw.*/
#define RMT_CH4_ERR_INT_CLR (BIT(14))
#define RMT_CH4_ERR_INT_CLR_M (BIT(14))
#define RMT_CH4_ERR_INT_CLR_V 0x1
#define RMT_CH4_ERR_INT_CLR_S 14
/* RMT_CH4_RX_END_INT_CLR : WO ;bitpos:[13] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch4_tx_end_int_raw.*/
#define RMT_CH4_RX_END_INT_CLR (BIT(13))
#define RMT_CH4_RX_END_INT_CLR_M (BIT(13))
#define RMT_CH4_RX_END_INT_CLR_V 0x1
#define RMT_CH4_RX_END_INT_CLR_S 13
/* RMT_CH4_TX_END_INT_CLR : WO ;bitpos:[12] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch4_rx_end_int_raw..*/
#define RMT_CH4_TX_END_INT_CLR (BIT(12))
#define RMT_CH4_TX_END_INT_CLR_M (BIT(12))
#define RMT_CH4_TX_END_INT_CLR_V 0x1
#define RMT_CH4_TX_END_INT_CLR_S 12
/* RMT_CH3_ERR_INT_CLR : WO ;bitpos:[11] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch3_err_int_raw.*/
#define RMT_CH3_ERR_INT_CLR (BIT(11))
#define RMT_CH3_ERR_INT_CLR_M (BIT(11))
#define RMT_CH3_ERR_INT_CLR_V 0x1
#define RMT_CH3_ERR_INT_CLR_S 11
/* RMT_CH3_RX_END_INT_CLR : WO ;bitpos:[10] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch3_tx_end_int_raw.*/
#define RMT_CH3_RX_END_INT_CLR (BIT(10))
#define RMT_CH3_RX_END_INT_CLR_M (BIT(10))
#define RMT_CH3_RX_END_INT_CLR_V 0x1
#define RMT_CH3_RX_END_INT_CLR_S 10
/* RMT_CH3_TX_END_INT_CLR : WO ;bitpos:[9] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch3_rx_end_int_raw..*/
#define RMT_CH3_TX_END_INT_CLR (BIT(9))
#define RMT_CH3_TX_END_INT_CLR_M (BIT(9))
#define RMT_CH3_TX_END_INT_CLR_V 0x1
#define RMT_CH3_TX_END_INT_CLR_S 9
/* RMT_CH2_ERR_INT_CLR : WO ;bitpos:[8] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch2_err_int_raw.*/
#define RMT_CH2_ERR_INT_CLR (BIT(8))
#define RMT_CH2_ERR_INT_CLR_M (BIT(8))
#define RMT_CH2_ERR_INT_CLR_V 0x1
#define RMT_CH2_ERR_INT_CLR_S 8
/* RMT_CH2_RX_END_INT_CLR : WO ;bitpos:[7] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch2_tx_end_int_raw.*/
#define RMT_CH2_RX_END_INT_CLR (BIT(7))
#define RMT_CH2_RX_END_INT_CLR_M (BIT(7))
#define RMT_CH2_RX_END_INT_CLR_V 0x1
#define RMT_CH2_RX_END_INT_CLR_S 7
/* RMT_CH2_TX_END_INT_CLR : WO ;bitpos:[6] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch2_rx_end_int_raw..*/
#define RMT_CH2_TX_END_INT_CLR (BIT(6))
#define RMT_CH2_TX_END_INT_CLR_M (BIT(6))
#define RMT_CH2_TX_END_INT_CLR_V 0x1
#define RMT_CH2_TX_END_INT_CLR_S 6
/* RMT_CH1_ERR_INT_CLR : WO ;bitpos:[5] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch1_err_int_raw.*/
#define RMT_CH1_ERR_INT_CLR (BIT(5))
#define RMT_CH1_ERR_INT_CLR_M (BIT(5))
#define RMT_CH1_ERR_INT_CLR_V 0x1
#define RMT_CH1_ERR_INT_CLR_S 5
/* RMT_CH1_RX_END_INT_CLR : WO ;bitpos:[4] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch1_tx_end_int_raw.*/
#define RMT_CH1_RX_END_INT_CLR (BIT(4))
#define RMT_CH1_RX_END_INT_CLR_M (BIT(4))
#define RMT_CH1_RX_END_INT_CLR_V 0x1
#define RMT_CH1_RX_END_INT_CLR_S 4
/* RMT_CH1_TX_END_INT_CLR : WO ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch1_rx_end_int_raw..*/
#define RMT_CH1_TX_END_INT_CLR (BIT(3))
#define RMT_CH1_TX_END_INT_CLR_M (BIT(3))
#define RMT_CH1_TX_END_INT_CLR_V 0x1
#define RMT_CH1_TX_END_INT_CLR_S 3
/* RMT_CH0_ERR_INT_CLR : WO ;bitpos:[2] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch0_err_int_raw.*/
#define RMT_CH0_ERR_INT_CLR (BIT(2))
#define RMT_CH0_ERR_INT_CLR_M (BIT(2))
#define RMT_CH0_ERR_INT_CLR_V 0x1
#define RMT_CH0_ERR_INT_CLR_S 2
/* RMT_CH0_RX_END_INT_CLR : WO ;bitpos:[1] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch0_tx_end_int_raw.*/
#define RMT_CH0_RX_END_INT_CLR (BIT(1))
#define RMT_CH0_RX_END_INT_CLR_M (BIT(1))
#define RMT_CH0_RX_END_INT_CLR_V 0x1
#define RMT_CH0_RX_END_INT_CLR_S 1
/* RMT_CH0_TX_END_INT_CLR : WO ;bitpos:[0] ;default: 1'b0 ; */
/*description: Set this bit to clear the rmt_ch0_rx_end_int_raw..*/
#define RMT_CH0_TX_END_INT_CLR (BIT(0))
#define RMT_CH0_TX_END_INT_CLR_M (BIT(0))
#define RMT_CH0_TX_END_INT_CLR_V 0x1
#define RMT_CH0_TX_END_INT_CLR_S 0
#define RMT_CH0CARRIER_DUTY_REG (DR_REG_RMT_BASE + 0x00b0)
/* RMT_CARRIER_HIGH_CH0 : R/W ;bitpos:[31:16] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's high level value for channel0.*/
#define RMT_CARRIER_HIGH_CH0 0x0000FFFF
#define RMT_CARRIER_HIGH_CH0_M ((RMT_CARRIER_HIGH_CH0_V)<<(RMT_CARRIER_HIGH_CH0_S))
#define RMT_CARRIER_HIGH_CH0_V 0xFFFF
#define RMT_CARRIER_HIGH_CH0_S 16
/* RMT_CARRIER_LOW_CH0 : R/W ;bitpos:[15:0] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's low level value for channel0.*/
#define RMT_CARRIER_LOW_CH0 0x0000FFFF
#define RMT_CARRIER_LOW_CH0_M ((RMT_CARRIER_LOW_CH0_V)<<(RMT_CARRIER_LOW_CH0_S))
#define RMT_CARRIER_LOW_CH0_V 0xFFFF
#define RMT_CARRIER_LOW_CH0_S 0
#define RMT_CH1CARRIER_DUTY_REG (DR_REG_RMT_BASE + 0x00b4)
/* RMT_CARRIER_HIGH_CH1 : R/W ;bitpos:[31:16] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's high level value for channel1.*/
#define RMT_CARRIER_HIGH_CH1 0x0000FFFF
#define RMT_CARRIER_HIGH_CH1_M ((RMT_CARRIER_HIGH_CH1_V)<<(RMT_CARRIER_HIGH_CH1_S))
#define RMT_CARRIER_HIGH_CH1_V 0xFFFF
#define RMT_CARRIER_HIGH_CH1_S 16
/* RMT_CARRIER_LOW_CH1 : R/W ;bitpos:[15:0] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's low level value for channel1.*/
#define RMT_CARRIER_LOW_CH1 0x0000FFFF
#define RMT_CARRIER_LOW_CH1_M ((RMT_CARRIER_LOW_CH1_V)<<(RMT_CARRIER_LOW_CH1_S))
#define RMT_CARRIER_LOW_CH1_V 0xFFFF
#define RMT_CARRIER_LOW_CH1_S 0
#define RMT_CH2CARRIER_DUTY_REG (DR_REG_RMT_BASE + 0x00b8)
/* RMT_CARRIER_HIGH_CH2 : R/W ;bitpos:[31:16] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's high level value for channel2.*/
#define RMT_CARRIER_HIGH_CH2 0x0000FFFF
#define RMT_CARRIER_HIGH_CH2_M ((RMT_CARRIER_HIGH_CH2_V)<<(RMT_CARRIER_HIGH_CH2_S))
#define RMT_CARRIER_HIGH_CH2_V 0xFFFF
#define RMT_CARRIER_HIGH_CH2_S 16
/* RMT_CARRIER_LOW_CH2 : R/W ;bitpos:[15:0] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's low level value for channel2.*/
#define RMT_CARRIER_LOW_CH2 0x0000FFFF
#define RMT_CARRIER_LOW_CH2_M ((RMT_CARRIER_LOW_CH2_V)<<(RMT_CARRIER_LOW_CH2_S))
#define RMT_CARRIER_LOW_CH2_V 0xFFFF
#define RMT_CARRIER_LOW_CH2_S 0
#define RMT_CH3CARRIER_DUTY_REG (DR_REG_RMT_BASE + 0x00bc)
/* RMT_CARRIER_HIGH_CH3 : R/W ;bitpos:[31:16] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's high level value for channel3.*/
#define RMT_CARRIER_HIGH_CH3 0x0000FFFF
#define RMT_CARRIER_HIGH_CH3_M ((RMT_CARRIER_HIGH_CH3_V)<<(RMT_CARRIER_HIGH_CH3_S))
#define RMT_CARRIER_HIGH_CH3_V 0xFFFF
#define RMT_CARRIER_HIGH_CH3_S 16
/* RMT_CARRIER_LOW_CH3 : R/W ;bitpos:[15:0] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's low level value for channel3.*/
#define RMT_CARRIER_LOW_CH3 0x0000FFFF
#define RMT_CARRIER_LOW_CH3_M ((RMT_CARRIER_LOW_CH3_V)<<(RMT_CARRIER_LOW_CH3_S))
#define RMT_CARRIER_LOW_CH3_V 0xFFFF
#define RMT_CARRIER_LOW_CH3_S 0
#define RMT_CH4CARRIER_DUTY_REG (DR_REG_RMT_BASE + 0x00c0)
/* RMT_CARRIER_HIGH_CH4 : R/W ;bitpos:[31:16] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's high level value for channel4.*/
#define RMT_CARRIER_HIGH_CH4 0x0000FFFF
#define RMT_CARRIER_HIGH_CH4_M ((RMT_CARRIER_HIGH_CH4_V)<<(RMT_CARRIER_HIGH_CH4_S))
#define RMT_CARRIER_HIGH_CH4_V 0xFFFF
#define RMT_CARRIER_HIGH_CH4_S 16
/* RMT_CARRIER_LOW_CH4 : R/W ;bitpos:[15:0] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's low level value for channel4.*/
#define RMT_CARRIER_LOW_CH4 0x0000FFFF
#define RMT_CARRIER_LOW_CH4_M ((RMT_CARRIER_LOW_CH4_V)<<(RMT_CARRIER_LOW_CH4_S))
#define RMT_CARRIER_LOW_CH4_V 0xFFFF
#define RMT_CARRIER_LOW_CH4_S 0
#define RMT_CH5CARRIER_DUTY_REG (DR_REG_RMT_BASE + 0x00c4)
/* RMT_CARRIER_HIGH_CH5 : R/W ;bitpos:[31:16] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's high level value for channel5.*/
#define RMT_CARRIER_HIGH_CH5 0x0000FFFF
#define RMT_CARRIER_HIGH_CH5_M ((RMT_CARRIER_HIGH_CH5_V)<<(RMT_CARRIER_HIGH_CH5_S))
#define RMT_CARRIER_HIGH_CH5_V 0xFFFF
#define RMT_CARRIER_HIGH_CH5_S 16
/* RMT_CARRIER_LOW_CH5 : R/W ;bitpos:[15:0] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's low level value for channel5.*/
#define RMT_CARRIER_LOW_CH5 0x0000FFFF
#define RMT_CARRIER_LOW_CH5_M ((RMT_CARRIER_LOW_CH5_V)<<(RMT_CARRIER_LOW_CH5_S))
#define RMT_CARRIER_LOW_CH5_V 0xFFFF
#define RMT_CARRIER_LOW_CH5_S 0
#define RMT_CH6CARRIER_DUTY_REG (DR_REG_RMT_BASE + 0x00c8)
/* RMT_CARRIER_HIGH_CH6 : R/W ;bitpos:[31:16] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's high level value for channel6.*/
#define RMT_CARRIER_HIGH_CH6 0x0000FFFF
#define RMT_CARRIER_HIGH_CH6_M ((RMT_CARRIER_HIGH_CH6_V)<<(RMT_CARRIER_HIGH_CH6_S))
#define RMT_CARRIER_HIGH_CH6_V 0xFFFF
#define RMT_CARRIER_HIGH_CH6_S 16
/* RMT_CARRIER_LOW_CH6 : R/W ;bitpos:[15:0] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's low level value for channel6.*/
#define RMT_CARRIER_LOW_CH6 0x0000FFFF
#define RMT_CARRIER_LOW_CH6_M ((RMT_CARRIER_LOW_CH6_V)<<(RMT_CARRIER_LOW_CH6_S))
#define RMT_CARRIER_LOW_CH6_V 0xFFFF
#define RMT_CARRIER_LOW_CH6_S 0
#define RMT_CH7CARRIER_DUTY_REG (DR_REG_RMT_BASE + 0x00cc)
/* RMT_CARRIER_HIGH_CH7 : R/W ;bitpos:[31:16] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's high level value for channel7.*/
#define RMT_CARRIER_HIGH_CH7 0x0000FFFF
#define RMT_CARRIER_HIGH_CH7_M ((RMT_CARRIER_HIGH_CH7_V)<<(RMT_CARRIER_HIGH_CH7_S))
#define RMT_CARRIER_HIGH_CH7_V 0xFFFF
#define RMT_CARRIER_HIGH_CH7_S 16
/* RMT_CARRIER_LOW_CH7 : R/W ;bitpos:[15:0] ;default: 16'h40 ; */
/*description: This register is used to configure carrier wave's low level value for channel7.*/
#define RMT_CARRIER_LOW_CH7 0x0000FFFF
#define RMT_CARRIER_LOW_CH7_M ((RMT_CARRIER_LOW_CH7_V)<<(RMT_CARRIER_LOW_CH7_S))
#define RMT_CARRIER_LOW_CH7_V 0xFFFF
#define RMT_CARRIER_LOW_CH7_S 0
#define RMT_CH0_TX_LIM_REG (DR_REG_RMT_BASE + 0x00d0)
/* RMT_TX_LIM_CH0 : R/W ;bitpos:[8:0] ;default: 9'h80 ; */
/*description: When channel0 sends more than reg_rmt_tx_lim_ch0 datas then channel0
produce the relative interrupt.*/
#define RMT_TX_LIM_CH0 0x000001FF
#define RMT_TX_LIM_CH0_M ((RMT_TX_LIM_CH0_V)<<(RMT_TX_LIM_CH0_S))
#define RMT_TX_LIM_CH0_V 0x1FF
#define RMT_TX_LIM_CH0_S 0
#define RMT_CH1_TX_LIM_REG (DR_REG_RMT_BASE + 0x00d4)
/* RMT_TX_LIM_CH1 : R/W ;bitpos:[8:0] ;default: 9'h80 ; */
/*description: When channel1 sends more than reg_rmt_tx_lim_ch1 datas then channel1
produce the relative interrupt.*/
#define RMT_TX_LIM_CH1 0x000001FF
#define RMT_TX_LIM_CH1_M ((RMT_TX_LIM_CH1_V)<<(RMT_TX_LIM_CH1_S))
#define RMT_TX_LIM_CH1_V 0x1FF
#define RMT_TX_LIM_CH1_S 0
#define RMT_CH2_TX_LIM_REG (DR_REG_RMT_BASE + 0x00d8)
/* RMT_TX_LIM_CH2 : R/W ;bitpos:[8:0] ;default: 9'h80 ; */
/*description: When channel2 sends more than reg_rmt_tx_lim_ch2 datas then channel2
produce the relative interrupt.*/
#define RMT_TX_LIM_CH2 0x000001FF
#define RMT_TX_LIM_CH2_M ((RMT_TX_LIM_CH2_V)<<(RMT_TX_LIM_CH2_S))
#define RMT_TX_LIM_CH2_V 0x1FF
#define RMT_TX_LIM_CH2_S 0
#define RMT_CH3_TX_LIM_REG (DR_REG_RMT_BASE + 0x00dc)
/* RMT_TX_LIM_CH3 : R/W ;bitpos:[8:0] ;default: 9'h80 ; */
/*description: When channel3 sends more than reg_rmt_tx_lim_ch3 datas then channel3
produce the relative interrupt.*/
#define RMT_TX_LIM_CH3 0x000001FF
#define RMT_TX_LIM_CH3_M ((RMT_TX_LIM_CH3_V)<<(RMT_TX_LIM_CH3_S))
#define RMT_TX_LIM_CH3_V 0x1FF
#define RMT_TX_LIM_CH3_S 0
#define RMT_CH4_TX_LIM_REG (DR_REG_RMT_BASE + 0x00e0)
/* RMT_TX_LIM_CH4 : R/W ;bitpos:[8:0] ;default: 9'h80 ; */
/*description: When channel4 sends more than reg_rmt_tx_lim_ch4 datas then channel4
produce the relative interrupt.*/
#define RMT_TX_LIM_CH4 0x000001FF
#define RMT_TX_LIM_CH4_M ((RMT_TX_LIM_CH4_V)<<(RMT_TX_LIM_CH4_S))
#define RMT_TX_LIM_CH4_V 0x1FF
#define RMT_TX_LIM_CH4_S 0
#define RMT_CH5_TX_LIM_REG (DR_REG_RMT_BASE + 0x00e4)
/* RMT_TX_LIM_CH5 : R/W ;bitpos:[8:0] ;default: 9'h80 ; */
/*description: When channel5 sends more than reg_rmt_tx_lim_ch5 datas then channel5
produce the relative interrupt.*/
#define RMT_TX_LIM_CH5 0x000001FF
#define RMT_TX_LIM_CH5_M ((RMT_TX_LIM_CH5_V)<<(RMT_TX_LIM_CH5_S))
#define RMT_TX_LIM_CH5_V 0x1FF
#define RMT_TX_LIM_CH5_S 0
#define RMT_CH6_TX_LIM_REG (DR_REG_RMT_BASE + 0x00e8)
/* RMT_TX_LIM_CH6 : R/W ;bitpos:[8:0] ;default: 9'h80 ; */
/*description: When channel6 sends more than reg_rmt_tx_lim_ch6 datas then channel6
produce the relative interrupt.*/
#define RMT_TX_LIM_CH6 0x000001FF
#define RMT_TX_LIM_CH6_M ((RMT_TX_LIM_CH6_V)<<(RMT_TX_LIM_CH6_S))
#define RMT_TX_LIM_CH6_V 0x1FF
#define RMT_TX_LIM_CH6_S 0
#define RMT_CH7_TX_LIM_REG (DR_REG_RMT_BASE + 0x00ec)
/* RMT_TX_LIM_CH7 : R/W ;bitpos:[8:0] ;default: 9'h80 ; */
/*description: When channel7 sends more than reg_rmt_tx_lim_ch7 datas then channel7
produce the relative interrupt.*/
#define RMT_TX_LIM_CH7 0x000001FF
#define RMT_TX_LIM_CH7_M ((RMT_TX_LIM_CH7_V)<<(RMT_TX_LIM_CH7_S))
#define RMT_TX_LIM_CH7_V 0x1FF
#define RMT_TX_LIM_CH7_S 0
#define RMT_APB_CONF_REG (DR_REG_RMT_BASE + 0x00f0)
/* RMT_MEM_TX_WRAP_EN : R/W ;bitpos:[1] ;default: 1'b0 ; */
/*description: when datas need to be send is more than channel's mem can store
then set this bit to enable reusage of mem this bit is used together with reg_rmt_tx_lim_chn.*/
#define RMT_MEM_TX_WRAP_EN (BIT(1))
#define RMT_MEM_TX_WRAP_EN_M (BIT(1))
#define RMT_MEM_TX_WRAP_EN_V 0x1
#define RMT_MEM_TX_WRAP_EN_S 1
/* RMT_APB_FIFO_MASK : R/W ;bitpos:[0] ;default: 1'h0 ; */
/*description: Set this bit to disable apb fifo access*/
#define RMT_APB_FIFO_MASK (BIT(0))
#define RMT_APB_FIFO_MASK_M (BIT(0))
#define RMT_APB_FIFO_MASK_V 0x1
#define RMT_APB_FIFO_MASK_S 0
#define RMT_DATE_REG (DR_REG_RMT_BASE + 0x00fc)
/* RMT_DATE : R/W ;bitpos:[31:0] ;default: 32'h16022600 ; */
/*description: This is the version register.*/
#define RMT_DATE 0xFFFFFFFF
#define RMT_DATE_M ((RMT_DATE_V)<<(RMT_DATE_S))
#define RMT_DATE_V 0xFFFFFFFF
#define RMT_DATE_S 0
#endif /*_SOC_RMT_REG_H_ */