kopia lustrzana https://github.com/espressif/esp-idf
80 wiersze
2.9 KiB
C
80 wiersze
2.9 KiB
C
/*
|
|
* SPDX-FileCopyrightText: 2020-2022 Espressif Systems (Shanghai) CO LTD
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
#include <stdbool.h>
|
|
#include <stdint.h>
|
|
#include <stddef.h>
|
|
#include <stdlib.h>
|
|
#include "esp32c2/rom/ets_sys.h"
|
|
#include "esp32c2/rom/rtc.h"
|
|
#include "esp32c2/rom/uart.h"
|
|
#include "soc/rtc.h"
|
|
#include "soc/rtc_periph.h"
|
|
#include "hal/regi2c_ctrl_ll.h"
|
|
#include "esp_hw_log.h"
|
|
#include "esp_cpu.h"
|
|
#include "sdkconfig.h"
|
|
#include "esp_rom_uart.h"
|
|
|
|
static const char *TAG = "rtc_clk_init";
|
|
|
|
void rtc_clk_init(rtc_clk_config_t cfg)
|
|
{
|
|
rtc_cpu_freq_config_t old_config, new_config;
|
|
|
|
/* Set tuning parameters for 8M and 150k clocks.
|
|
* Note: this doesn't attempt to set the clocks to precise frequencies.
|
|
* Instead, we calibrate these clocks against XTAL frequency later, when necessary.
|
|
* - SCK_DCAP value controls tuning of 150k clock.
|
|
* The higher the value of DCAP is, the lower is the frequency.
|
|
* - CK8M_DFREQ value controls tuning of 8M clock.
|
|
* CLK_8M_DFREQ constant gives the best temperature characteristics.
|
|
*/
|
|
REG_SET_FIELD(RTC_CNTL_REG, RTC_CNTL_SCK_DCAP, cfg.slow_clk_dcap);
|
|
REG_SET_FIELD(RTC_CNTL_CLK_CONF_REG, RTC_CNTL_CK8M_DFREQ, cfg.clk_8m_dfreq);
|
|
|
|
/* Configure 150k clock division */
|
|
rtc_clk_divider_set(cfg.clk_rtc_clk_div);
|
|
|
|
/* Configure 8M clock division */
|
|
rtc_clk_8m_divider_set(cfg.clk_8m_clk_div);
|
|
|
|
/* Reset (disable) i2c internal bus for all regi2c registers */
|
|
regi2c_ctrl_ll_i2c_reset(); // TODO: This should be move out from rtc_clk_init
|
|
/* Enable the internal bus used to configure BBPLL */
|
|
regi2c_ctrl_ll_i2c_bbpll_enable(); // TODO: This should be moved to bbpll_set_config
|
|
|
|
rtc_xtal_freq_t xtal_freq = cfg.xtal_freq;
|
|
esp_rom_uart_tx_wait_idle(0);
|
|
rtc_clk_xtal_freq_update(xtal_freq);
|
|
rtc_clk_apb_freq_update(xtal_freq * MHZ);
|
|
|
|
/* Set CPU frequency */
|
|
rtc_clk_cpu_freq_get_config(&old_config);
|
|
uint32_t freq_before = old_config.freq_mhz;
|
|
bool res = rtc_clk_cpu_freq_mhz_to_config(cfg.cpu_freq_mhz, &new_config);
|
|
if (!res) {
|
|
ESP_HW_LOGE(TAG, "invalid CPU frequency value");
|
|
abort();
|
|
}
|
|
rtc_clk_cpu_freq_set_config(&new_config);
|
|
|
|
/* Re-calculate the ccount to make time calculation correct. */
|
|
esp_cpu_set_cycle_count( (uint64_t)esp_cpu_get_cycle_count() * cfg.cpu_freq_mhz / freq_before );
|
|
|
|
/* Slow & fast clocks setup */
|
|
// We will not power off RC_FAST in bootloader stage even if it is not being used as any
|
|
// cpu / rtc_fast / rtc_slow clock sources, this is because RNG always needs it in the bootloader stage.
|
|
bool need_rc_fast_en = true;
|
|
bool need_rc_fast_d256_en = false;
|
|
if (cfg.slow_clk_src == SOC_RTC_SLOW_CLK_SRC_RC_FAST_D256) {
|
|
need_rc_fast_d256_en = true;
|
|
}
|
|
rtc_clk_8m_enable(need_rc_fast_en, need_rc_fast_d256_en);
|
|
rtc_clk_fast_src_set(cfg.fast_clk_src);
|
|
rtc_clk_slow_src_set(cfg.slow_clk_src);
|
|
}
|