kopia lustrzana https://github.com/espressif/esp-idf
98 wiersze
3.7 KiB
C
98 wiersze
3.7 KiB
C
/* i2c - Simple example
|
|
|
|
Simple I2C example that shows how to initialize I2C
|
|
as well as reading and writing from and to registers for a sensor connected over I2C.
|
|
|
|
The sensor used in this example is a MPU9250 inertial measurement unit.
|
|
|
|
For other examples please check:
|
|
https://github.com/espressif/esp-idf/tree/master/examples
|
|
|
|
See README.md file to get detailed usage of this example.
|
|
|
|
This example code is in the Public Domain (or CC0 licensed, at your option.)
|
|
|
|
Unless required by applicable law or agreed to in writing, this
|
|
software is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
|
|
CONDITIONS OF ANY KIND, either express or implied.
|
|
*/
|
|
#include <stdio.h>
|
|
#include "esp_log.h"
|
|
#include "driver/i2c.h"
|
|
|
|
static const char *TAG = "i2c-simple-example";
|
|
|
|
#define I2C_MASTER_SCL_IO CONFIG_I2C_MASTER_SCL /*!< GPIO number used for I2C master clock */
|
|
#define I2C_MASTER_SDA_IO CONFIG_I2C_MASTER_SDA /*!< GPIO number used for I2C master data */
|
|
#define I2C_MASTER_NUM 0 /*!< I2C master i2c port number, the number of i2c peripheral interfaces available will depend on the chip */
|
|
#define I2C_MASTER_FREQ_HZ 400000 /*!< I2C master clock frequency */
|
|
#define I2C_MASTER_TX_BUF_DISABLE 0 /*!< I2C master doesn't need buffer */
|
|
#define I2C_MASTER_RX_BUF_DISABLE 0 /*!< I2C master doesn't need buffer */
|
|
#define I2C_MASTER_TIMEOUT_MS 1000
|
|
|
|
#define MPU9250_SENSOR_ADDR 0x68 /*!< Slave address of the MPU9250 sensor */
|
|
#define MPU9250_WHO_AM_I_REG_ADDR 0x75 /*!< Register addresses of the "who am I" register */
|
|
|
|
#define MPU9250_PWR_MGMT_1_REG_ADDR 0x6B /*!< Register addresses of the power managment register */
|
|
#define MPU9250_RESET_BIT 7
|
|
|
|
/**
|
|
* @brief Read a sequence of bytes from a MPU9250 sensor registers
|
|
*/
|
|
static esp_err_t mpu9250_register_read(uint8_t reg_addr, uint8_t *data, size_t len)
|
|
{
|
|
return i2c_master_write_read_device(I2C_MASTER_NUM, MPU9250_SENSOR_ADDR, ®_addr, 1, data, len, I2C_MASTER_TIMEOUT_MS / portTICK_RATE_MS);
|
|
}
|
|
|
|
/**
|
|
* @brief Write a byte to a MPU9250 sensor register
|
|
*/
|
|
static esp_err_t mpu9250_register_write_byte(uint8_t reg_addr, uint8_t data)
|
|
{
|
|
int ret;
|
|
uint8_t write_buf[2] = {reg_addr, data};
|
|
|
|
ret = i2c_master_write_to_device(I2C_MASTER_NUM, MPU9250_SENSOR_ADDR, write_buf, sizeof(write_buf), I2C_MASTER_TIMEOUT_MS / portTICK_RATE_MS);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/**
|
|
* @brief i2c master initialization
|
|
*/
|
|
static esp_err_t i2c_master_init(void)
|
|
{
|
|
int i2c_master_port = I2C_MASTER_NUM;
|
|
|
|
i2c_config_t conf = {
|
|
.mode = I2C_MODE_MASTER,
|
|
.sda_io_num = I2C_MASTER_SDA_IO,
|
|
.scl_io_num = I2C_MASTER_SCL_IO,
|
|
.sda_pullup_en = GPIO_PULLUP_ENABLE,
|
|
.scl_pullup_en = GPIO_PULLUP_ENABLE,
|
|
.master.clk_speed = I2C_MASTER_FREQ_HZ,
|
|
};
|
|
|
|
i2c_param_config(i2c_master_port, &conf);
|
|
|
|
return i2c_driver_install(i2c_master_port, conf.mode, I2C_MASTER_RX_BUF_DISABLE, I2C_MASTER_TX_BUF_DISABLE, 0);
|
|
}
|
|
|
|
|
|
void app_main(void)
|
|
{
|
|
uint8_t data[2];
|
|
ESP_ERROR_CHECK(i2c_master_init());
|
|
ESP_LOGI(TAG, "I2C initialized successfully");
|
|
|
|
/* Read the MPU9250 WHO_AM_I register, on power up the register should have the value 0x71 */
|
|
ESP_ERROR_CHECK(mpu9250_register_read(MPU9250_WHO_AM_I_REG_ADDR, data, 1));
|
|
ESP_LOGI(TAG, "WHO_AM_I = %X", data[0]);
|
|
|
|
/* Demonstrate writing by reseting the MPU9250 */
|
|
ESP_ERROR_CHECK(mpu9250_register_write_byte(MPU9250_PWR_MGMT_1_REG_ADDR, 1 << MPU9250_RESET_BIT));
|
|
|
|
ESP_ERROR_CHECK(i2c_driver_delete(I2C_MASTER_NUM));
|
|
ESP_LOGI(TAG, "I2C unitialized successfully");
|
|
}
|