esp-idf/examples/system/ulp/main/ulp_example_main.c

107 wiersze
3.7 KiB
C

/* ULP Example
This example code is in the Public Domain (or CC0 licensed, at your option.)
Unless required by applicable law or agreed to in writing, this
software is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
CONDITIONS OF ANY KIND, either express or implied.
*/
#include <stdio.h>
#include "esp_deep_sleep.h"
#include "nvs.h"
#include "nvs_flash.h"
#include "soc/rtc_cntl_reg.h"
#include "soc/sens_reg.h"
#include "driver/gpio.h"
#include "driver/rtc_io.h"
#include "esp32/ulp.h"
#include "ulp_main.h"
extern const uint8_t ulp_main_bin_start[] asm("_binary_ulp_main_bin_start");
extern const uint8_t ulp_main_bin_end[] asm("_binary_ulp_main_bin_end");
static void init_ulp_program();
static void update_pulse_count();
void app_main()
{
esp_deep_sleep_wakeup_cause_t cause = esp_deep_sleep_get_wakeup_cause();
if (cause != ESP_DEEP_SLEEP_WAKEUP_ULP) {
printf("Not ULP wakeup, initializing ULP\n");
init_ulp_program();
} else {
printf("ULP wakeup, saving pulse count\n");
update_pulse_count();
}
printf("Entering deep sleep\n\n");
ESP_ERROR_CHECK( esp_deep_sleep_enable_ulp_wakeup() );
esp_deep_sleep_start();
}
static void init_ulp_program()
{
esp_err_t err = ulp_load_binary(0, ulp_main_bin_start,
(ulp_main_bin_end - ulp_main_bin_start) / sizeof(uint32_t));
ESP_ERROR_CHECK(err);
/* Initialize some variables used by ULP program.
* Each 'ulp_xyz' variable corresponds to 'xyz' variable in the ULP program.
* These variables are declared in an auto generated header file,
* 'ulp_main.h', name of this file is defined in component.mk as ULP_APP_NAME.
* These variables are located in RTC_SLOW_MEM and can be accessed both by the
* ULP and the main CPUs.
*
* Note that the ULP reads only the lower 16 bits of these variables.
*/
ulp_debounce_counter = 3;
ulp_debounce_max_count = 3;
ulp_next_edge = 0;
ulp_io_number = 11; /* GPIO0 is RTC_IO 11 */
ulp_edge_count_to_wake_up = 10;
/* Initialize GPIO0 as RTC IO, input, disable pullup and pulldown */
gpio_num_t gpio_num = GPIO_NUM_0;
rtc_gpio_set_direction(gpio_num, RTC_GPIO_MODE_INPUT_ONLY);
rtc_gpio_pulldown_dis(gpio_num);
rtc_gpio_pullup_dis(gpio_num);
rtc_gpio_hold_en(gpio_num);
/* Set ULP wake up period to T = 20ms (3095 cycles of RTC_SLOW_CLK clock).
* Minimum pulse width has to be T * (ulp_debounce_counter + 1) = 80ms.
*/
REG_SET_FIELD(SENS_ULP_CP_SLEEP_CYC0_REG, SENS_SLEEP_CYCLES_S0, 3095);
/* Start the program */
err = ulp_run((&ulp_entry - RTC_SLOW_MEM) / sizeof(uint32_t));
ESP_ERROR_CHECK(err);
}
static void update_pulse_count()
{
const char* namespace = "plusecnt";
const char* count_key = "count";
ESP_ERROR_CHECK( nvs_flash_init() );
nvs_handle handle;
ESP_ERROR_CHECK( nvs_open(namespace, NVS_READWRITE, &handle));
uint32_t pulse_count = 0;
esp_err_t err = nvs_get_u32(handle, count_key, &pulse_count);
assert(err == ESP_OK || err == ESP_ERR_NVS_NOT_FOUND);
printf("Read pulse count from NVS: %5d\n", pulse_count);
/* ULP program counts signal edges, convert that to the number of pulses */
uint32_t pulse_count_from_ulp = (ulp_edge_count & UINT16_MAX) / 2;
/* In case of an odd number of edges, keep one until next time */
ulp_edge_count = ulp_edge_count % 2;
printf("Pulse count from ULP: %5d\n", pulse_count_from_ulp);
/* Save the new pulse count to NVS */
pulse_count += pulse_count_from_ulp;
ESP_ERROR_CHECK(nvs_set_u32(handle, count_key, pulse_count));
ESP_ERROR_CHECK(nvs_commit(handle));
nvs_close(handle);
printf("Wrote updated pulse count to NVS: %5d\n", pulse_count);
}