esp-idf/components/esp_eth/Kconfig

181 wiersze
6.9 KiB
Plaintext

menu "Ethernet"
# Invisible item that is enabled if any Ethernet selection is made
config ETH_ENABLED
bool
menuconfig ETH_USE_ESP32_EMAC
depends on IDF_TARGET_ESP32
bool "Support ESP32 internal EMAC controller"
default y
select ETH_ENABLED
help
ESP32 integrates a 10/100M Ethernet MAC controller.
if ETH_USE_ESP32_EMAC
choice ETH_PHY_INTERFACE
prompt "PHY interface"
default ETH_PHY_INTERFACE_RMII
help
Select the communication interface between MAC and PHY chip.
config ETH_PHY_INTERFACE_RMII
bool "Reduced Media Independent Interface (RMII)"
endchoice
if ETH_PHY_INTERFACE_RMII
choice ETH_RMII_CLK_MODE
prompt "RMII clock mode"
default ETH_RMII_CLK_INPUT
help
Select external or internal RMII clock.
config ETH_RMII_CLK_INPUT
bool "Input RMII clock from external"
help
MAC will get RMII clock from outside.
Note that ESP32 only supports GPIO0 to input the RMII clock.
config ETH_RMII_CLK_OUTPUT
bool "Output RMII clock from internal"
help
ESP32 can generate RMII clock by internal APLL.
This clock can be routed to the external PHY device.
ESP32 supports to route the RMII clock to GPIO0/16/17.
endchoice
endif # ETH_PHY_INTERFACE_RMII
if ETH_RMII_CLK_INPUT
config ETH_RMII_CLK_IN_GPIO
int
range 0 0
default 0
help
ESP32 only supports GPIO0 to input the RMII clock.
endif # ETH_RMII_CLK_INPUT
if ETH_RMII_CLK_OUTPUT
config ETH_RMII_CLK_OUTPUT_GPIO0
bool "Output RMII clock from GPIO0 (Experimental!)"
default n
help
GPIO0 can be set to output a pre-divided PLL clock (test only!).
Enabling this option will configure GPIO0 to output a 50MHz clock.
In fact this clock doesn't have directly relationship with EMAC peripheral.
Sometimes this clock won't work well with your PHY chip. You might need to
add some extra devices after GPIO0 (e.g. inverter).
Note that outputting RMII clock on GPIO0 is an experimental practice.
If you want the Ethernet to work with WiFi, don't select GPIO0 output mode for stability.
if !ETH_RMII_CLK_OUTPUT_GPIO0
config ETH_RMII_CLK_OUT_GPIO
int "RMII clock GPIO number"
range 16 17
default 17
help
Set the GPIO number to output RMII Clock.
endif # !ETH_RMII_CLK_OUTPUT_GPIO0
endif # ETH_RMII_CLK_OUTPUT
config ETH_DMA_BUFFER_SIZE
int "Ethernet DMA buffer size (Byte)"
range 256 1600
default 512
help
Set the size of each buffer used by Ethernet MAC DMA.
config ETH_DMA_RX_BUFFER_NUM
int "Amount of Ethernet DMA Rx buffers"
range 3 30
default 10
help
Number of DMA receive buffers. Each buffer's size is ETH_DMA_BUFFER_SIZE.
Larger number of buffers could increase throughput somehow.
config ETH_DMA_TX_BUFFER_NUM
int "Amount of Ethernet DMA Tx buffers"
range 3 30
default 10
help
Number of DMA transmit buffers. Each buffer's size is ETH_DMA_BUFFER_SIZE.
Larger number of buffers could increase throughput somehow.
if ETH_DMA_RX_BUFFER_NUM > 15
config ETH_SOFT_FLOW_CONTROL
bool "Enable software flow control"
default n
help
Ethernet MAC engine on ESP32 doesn't feature a flow control logic.
The MAC driver can perform a software flow control if you enable this option.
Note that, if the RX buffer number is small, enabling software flow control will
cause obvious performance loss.
endif
endif # ETH_USE_ESP32_EMAC
menuconfig ETH_USE_SPI_ETHERNET
bool "Support SPI to Ethernet Module"
default y
select ETH_ENABLED
help
ESP-IDF can also support some SPI-Ethernet modules.
if ETH_USE_SPI_ETHERNET
config ETH_SPI_ETHERNET_DM9051
bool "Use DM9051"
help
DM9051 is a fast Ethernet controller with an SPI interface.
It's also integrated with a 10/100M PHY and MAC.
Select this to enable DM9051 driver.
config ETH_SPI_ETHERNET_W5500
bool "Use W5500 (MAC RAW)"
help
W5500 is a HW TCP/IP embedded Ethernet controller.
TCP/IP stack, 10/100 Ethernet MAC and PHY are embedded in a single chip.
However the driver in ESP-IDF only enables the RAW MAC mode,
making it compatible with the software TCP/IP stack.
Say yes to enable W5500 driver.
config ETH_SPI_ETHERNET_KSZ8851SNL
bool "Use KSZ8851SNL"
help
The KSZ8851SNL is a single-chip Fast Ethernet controller consisting of
a 10/100 physical layer transceiver (PHY), a MAC, and a Serial Peripheral Interface (SPI).
Select this to enable KSZ8851SNL driver.
endif # ETH_USE_SPI_ETHERNET
menuconfig ETH_USE_OPENETH
bool "Support OpenCores Ethernet MAC (for use with QEMU)"
default n
select ETH_ENABLED
help
OpenCores Ethernet MAC driver can be used when an ESP-IDF application
is executed in QEMU. This driver is not supported when running on a
real chip.
if ETH_USE_OPENETH
config ETH_OPENETH_DMA_RX_BUFFER_NUM
int "Number of Ethernet DMA Rx buffers"
range 1 64
default 4
help
Number of DMA receive buffers, each buffer is 1600 bytes.
config ETH_OPENETH_DMA_TX_BUFFER_NUM
int "Number of Ethernet DMA Tx buffers"
range 1 64
default 1
help
Number of DMA transmit buffers, each buffer is 1600 bytes.
endif # ETH_USE_OPENETH
config ETH_TRANSMIT_MUTEX
depends on ETH_ENABLED
bool "Enable Transmit Mutex"
default n
help
Prevents multiple accesses when Ethernet interface is used as shared resource and multiple
functionalities might try to access it at a time.
endmenu