kopia lustrzana https://github.com/espressif/esp-idf
221 wiersze
7.8 KiB
ReStructuredText
221 wiersze
7.8 KiB
ReStructuredText
I2S
|
|
===
|
|
|
|
Overview
|
|
--------
|
|
|
|
I2S (Inter-IC Sound) is a serial, synchronous communication protocol that is usually used for transmitting audio data between two digital audio devices.
|
|
|
|
.. only:: esp32
|
|
|
|
{IDF_TARGET_NAME} contains two I2S peripherals. These peripherals can be configured to input and output sample data via the I2S driver.
|
|
|
|
.. only:: esp32s2
|
|
|
|
{IDF_TARGET_NAME} contains one I2S peripheral. These peripherals can be configured to input and output sample data via the I2S driver.
|
|
|
|
An I2S bus consists of the following lines:
|
|
|
|
- Bit clock line
|
|
- Channel select line
|
|
- Serial data line
|
|
|
|
Each I2S controller has the following features that can be configured using the I2S driver:
|
|
|
|
- Operation as system master or slave
|
|
- Capable of acting as transmitter or receiver
|
|
- Dedicated DMA controller that allows for streaming sample data without requiring the CPU to copy each data sample
|
|
|
|
Each controller can operate in half-duplex communication mode. Thus, the two controllers can be combined to establish full-duplex communication.
|
|
|
|
I2S0 output can be routed directly to the digital-to-analog converter's (DAC) output channels (GPIO 25 & GPIO 26) to produce direct analog output without involving any external I2S codecs. I2S0 can also be used for transmitting PDM (Pulse-density modulation) signals.
|
|
|
|
The I2S peripherals also support LCD mode for communicating data over a parallel bus, as used by some LCD displays and camera modules. LCD mode has the following operational modes:
|
|
|
|
- LCD master transmitting mode
|
|
- Camera slave receiving mode
|
|
- ADC/DAC mode
|
|
|
|
.. only:: esp32
|
|
|
|
For more information, see the `ESP32 Technical Reference Manual <https://espressif.com/sites/default/files/documentation/esp32_technical_reference_manual_en.pdf#page=306>`_.
|
|
|
|
.. note::
|
|
|
|
For high accuracy clock applications, use the APLL_CLK clock source, which has the frequency range of 16 ~ 128 MHz. You can enable the APLL_CLK clock source by setting :cpp:member:`i2s_config_t::use_apll` to ``TRUE``.
|
|
|
|
If :cpp:member:`i2s_config_t::use_apll` = ``TRUE`` and :cpp:member:`i2s_config_t::fixed_mclk` > ``0``, then the master clock output frequency for I2S will be equal to the value of :cpp:member:`i2s_config_t::fixed_mclk`, which means that the mclk frequency is provided by the user, instead of being calculated by the driver.
|
|
|
|
The clock rate of the word select line, which is called audio left-right clock rate (LRCK) here, is always the divisor of the master clock output frequency and for which the following is always true: 0 < MCLK/LRCK/channels/bits_per_sample < 64.
|
|
|
|
|
|
Functional Overview
|
|
-------------------
|
|
|
|
|
|
Installing the Driver
|
|
^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
Install the I2S driver by calling the function :cpp:func`i2s_driver_install` and passing the following arguments:
|
|
|
|
- Port number
|
|
- The structure :cpp:type:`i2s_config_t` with defined communication parameters
|
|
- Event queue size and handle
|
|
|
|
Configuration example:
|
|
|
|
.. code-block:: c
|
|
|
|
static const int i2s_num = 0; // i2s port number
|
|
|
|
static const i2s_config_t i2s_config = {
|
|
.mode = I2S_MODE_MASTER | I2S_MODE_TX,
|
|
.sample_rate = 44100,
|
|
.bits_per_sample = 16,
|
|
.channel_format = I2S_CHANNEL_FMT_RIGHT_LEFT,
|
|
.communication_format = I2S_COMM_FORMAT_I2S | I2S_COMM_FORMAT_I2S_MSB,
|
|
.intr_alloc_flags = 0, // default interrupt priority
|
|
.dma_buf_count = 8,
|
|
.dma_buf_len = 64,
|
|
.use_apll = false
|
|
};
|
|
|
|
i2s_driver_install(I2S_NUM, &i2s_config, 0, NULL);
|
|
|
|
|
|
Setting Communication Pins
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
Once the driver is installed, configure physical GPIO pins to which signals will be routed. For this, call the function :cpp:func`i2s_set_pin` and pass the following arguments to it:
|
|
|
|
- Port number
|
|
- The structure :cpp:type:`i2s_pin_config_t` defining the GPIO pin numbers to which the driver should route the BCK, WS, DATA out, and DATA in signals. If you want to keep a currently allocated pin number for a specific signal, or if this signal is unused, then pass the macro :c:macro:`I2S_PIN_NO_CHANGE`. See the example below.
|
|
|
|
.. code-block:: c
|
|
|
|
static const i2s_pin_config_t pin_config = {
|
|
.bck_io_num = 26,
|
|
.ws_io_num = 25,
|
|
.data_out_num = 22,
|
|
.data_in_num = I2S_PIN_NO_CHANGE
|
|
};
|
|
|
|
i2s_set_pin(i2s_num, &pin_config);
|
|
|
|
|
|
Running I2S Communication
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
To perform a transmission:
|
|
|
|
- Prepare the data for sending
|
|
- Call the function :cpp:func:`i2s_write` and pass the data buffer address and data length to it
|
|
|
|
The function will write the data to the I2S DMA Tx buffer, and then the data will be transmitted automatically.
|
|
|
|
.. code-block:: c
|
|
|
|
i2s_write(I2S_NUM, samples_data, ((bits+8)/16)*SAMPLE_PER_CYCLE*4, &i2s_bytes_write, 100);
|
|
|
|
|
|
To retrieve received data, use the function :cpp:func:`i2s_read`. It will retrieve the data from the I2S DMA Rx buffer, once the data is received by the I2S controller.
|
|
|
|
You can temporarily stop the I2S driver by calling the function :cpp:func:`i2s_stop`, which will disable the I2S Tx/Rx units until the function :cpp:func:`i2s_start` is called. If the function :cpp:func`i2s_driver_install` is used, the driver will start up automatically eliminating the need to call :cpp:func:`i2s_start`.
|
|
|
|
|
|
Deleting the Driver
|
|
^^^^^^^^^^^^^^^^^^^
|
|
|
|
If the established communication is no longer required, the driver can be removed to free allocated resources by calling :cpp:func:`i2s_driver_uninstall`.
|
|
|
|
|
|
Application Example
|
|
-------------------
|
|
|
|
A code example for the I2S driver can be found in the directory :example:`peripherals/i2s`.
|
|
|
|
In addition, there are two short configuration examples for the I2S driver.
|
|
|
|
|
|
I2S configuration
|
|
^^^^^^^^^^^^^^^^^
|
|
|
|
.. code-block:: c
|
|
|
|
#include "driver/i2s.h"
|
|
#include "freertos/queue.h"
|
|
|
|
static const int i2s_num = 0; // i2s port number
|
|
|
|
static const i2s_config_t i2s_config = {
|
|
.mode = I2S_MODE_MASTER | I2S_MODE_TX,
|
|
.sample_rate = 44100,
|
|
.bits_per_sample = 16,
|
|
.channel_format = I2S_CHANNEL_FMT_RIGHT_LEFT,
|
|
.communication_format = I2S_COMM_FORMAT_I2S | I2S_COMM_FORMAT_I2S_MSB,
|
|
.intr_alloc_flags = 0, // default interrupt priority
|
|
.dma_buf_count = 8,
|
|
.dma_buf_len = 64,
|
|
.use_apll = false
|
|
};
|
|
|
|
static const i2s_pin_config_t pin_config = {
|
|
.bck_io_num = 26,
|
|
.ws_io_num = 25,
|
|
.data_out_num = 22,
|
|
.data_in_num = I2S_PIN_NO_CHANGE
|
|
};
|
|
|
|
...
|
|
|
|
i2s_driver_install(i2s_num, &i2s_config, 0, NULL); //install and start i2s driver
|
|
|
|
i2s_set_pin(i2s_num, &pin_config);
|
|
|
|
i2s_set_sample_rates(i2s_num, 22050); //set sample rates
|
|
|
|
i2s_driver_uninstall(i2s_num); //stop & destroy i2s driver
|
|
|
|
|
|
Configuring I2S to use internal DAC for analog output
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
.. code-block:: c
|
|
|
|
#include "driver/i2s.h"
|
|
#include "freertos/queue.h"
|
|
|
|
static const int i2s_num = 0; // i2s port number
|
|
|
|
static const i2s_config_t i2s_config = {
|
|
.mode = I2S_MODE_MASTER | I2S_MODE_TX | I2S_MODE_DAC_BUILT_IN,
|
|
.sample_rate = 44100,
|
|
.bits_per_sample = 16, /* the DAC module will only take the 8bits from MSB */
|
|
.channel_format = I2S_CHANNEL_FMT_RIGHT_LEFT,
|
|
.communication_format = I2S_COMM_FORMAT_I2S_MSB,
|
|
.intr_alloc_flags = 0, // default interrupt priority
|
|
.dma_buf_count = 8,
|
|
.dma_buf_len = 64,
|
|
.use_apll = false
|
|
};
|
|
|
|
...
|
|
|
|
i2s_driver_install(i2s_num, &i2s_config, 0, NULL); //install and start i2s driver
|
|
|
|
i2s_set_pin(i2s_num, NULL); //for internal DAC, this will enable both of the internal channels
|
|
|
|
//You can call i2s_set_dac_mode to set built-in DAC output mode.
|
|
//i2s_set_dac_mode(I2S_DAC_CHANNEL_BOTH_EN);
|
|
|
|
i2s_set_sample_rates(i2s_num, 22050); //set sample rates
|
|
|
|
i2s_driver_uninstall(i2s_num); //stop & destroy i2s driver
|
|
|
|
|
|
API Reference
|
|
-------------
|
|
|
|
.. include-build-file:: inc/i2s.inc
|
|
|