kopia lustrzana https://github.com/espressif/esp-idf
111 wiersze
5.3 KiB
Plaintext
111 wiersze
5.3 KiB
Plaintext
menu "USB-OTG"
|
|
visible if IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32S3
|
|
|
|
# Invisible item, enabled when USB_OTG peripheral does exist
|
|
config USB_OTG_SUPPORTED
|
|
bool
|
|
default y if IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32S3
|
|
|
|
config USB_HOST_CONTROL_TRANSFER_MAX_SIZE
|
|
depends on USB_OTG_SUPPORTED
|
|
int "Largest size (in bytes) of transfers to/from default endpoints"
|
|
default 256
|
|
help
|
|
Each USB device attached is allocated a dedicated buffer for its OUT/IN transfers to/from the device's
|
|
control endpoint. The maximum size of that buffer is determined by this option. The limited size of the
|
|
transfer buffer have the following implications:
|
|
- The maximum length of control transfers is limited
|
|
- Device's with configuration descriptors larger than this limit cannot be supported
|
|
|
|
choice USB_HOST_HW_BUFFER_BIAS
|
|
depends on USB_OTG_SUPPORTED
|
|
prompt "Hardware FIFO size biasing"
|
|
default USB_HOST_HW_BUFFER_BIAS_BALANCED
|
|
help
|
|
The underlying hardware has size adjustable FIFOs to cache USB packets on reception (IN) or for
|
|
transmission (OUT). The size of these FIFOs will affect the largest MPS (maximum packet size) and the
|
|
maximum number of packets that can be cached at any one time. The hardware contains the following
|
|
FIFOS: RX (for all IN packets), Non-periodic TX (for Bulk and Control OUT packets), and Periodic TX
|
|
(for Interrupt and Isochronous OUT packets). This configuration option allows biasing the FIFO sizes
|
|
towards a particular use case, which may be necessary for devices that have endpoints with large MPS.
|
|
The MPS limits for each biasing are listed below:
|
|
|
|
Balanced:
|
|
- IN (all transfer types), 408 bytes
|
|
- OUT non-periodic (Bulk/Control), 192 bytes (i.e., 3 x 64 byte packets)
|
|
- OUT periodic (Interrupt/Isochronous), 192 bytes
|
|
|
|
Bias IN:
|
|
- IN (all transfer types), 600 bytes
|
|
- OUT non-periodic (Bulk/Control), 64 bytes (i.e., 1 x 64 byte packets)
|
|
- OUT periodic (Interrupt/Isochronous), 128 bytes
|
|
|
|
Bias Periodic OUT:
|
|
- IN (all transfer types), 128 bytes
|
|
- OUT non-periodic (Bulk/Control), 64 bytes (i.e., 1 x 64 byte packets)
|
|
- OUT periodic (Interrupt/Isochronous), 600 bytes
|
|
|
|
config USB_HOST_HW_BUFFER_BIAS_BALANCED
|
|
bool "Balanced"
|
|
config USB_HOST_HW_BUFFER_BIAS_IN
|
|
bool "Bias IN"
|
|
config USB_HOST_HW_BUFFER_BIAS_PERIODIC_OUT
|
|
bool "Periodic OUT"
|
|
endchoice
|
|
|
|
menu "Root Hub configuration"
|
|
|
|
config USB_HOST_DEBOUNCE_DELAY_MS
|
|
depends on USB_OTG_SUPPORTED
|
|
int "Debounce delay in ms"
|
|
default 250
|
|
help
|
|
On connection of a USB device, the USB 2.0 specification requires a "debounce interval with a minimum
|
|
duration of 100ms" to allow the connection to stabilize (see USB 2.0 chapter 7.1.7.3 for more details).
|
|
During the debounce interval, no new connection/disconnection events are registered.
|
|
|
|
The default value is set to 250 ms to be safe.
|
|
|
|
config USB_HOST_RESET_HOLD_MS
|
|
depends on USB_OTG_SUPPORTED
|
|
int "Reset hold in ms"
|
|
default 30
|
|
help
|
|
The reset signaling can be generated on any Hub or Host Controller port by request from the USB System
|
|
Software. The USB 2.0 specification requires that "the reset signaling must be driven for a minimum of
|
|
10ms" (see USB 2.0 chapter 7.1.7.5 for more details). After the reset, the hub port will transition to
|
|
the Enabled state (refer to Section 11.5).
|
|
|
|
The default value is set to 30 ms to be safe.
|
|
|
|
config USB_HOST_RESET_RECOVERY_MS
|
|
depends on USB_OTG_SUPPORTED
|
|
int "Reset recovery delay in ms"
|
|
default 30
|
|
help
|
|
After a port stops driving the reset signal, the USB 2.0 specification requires that the "USB System
|
|
Software guarantees a minimum of 10 ms for reset recovery" before the attached device is expected to
|
|
respond to data transfers (see USB 2.0 chapter 7.1.7.3 for more details). The device may ignore any
|
|
data transfers during the recovery interval.
|
|
|
|
The default value is set to 30 ms to be safe.
|
|
|
|
|
|
config USB_HOST_SET_ADDR_RECOVERY_MS
|
|
depends on USB_OTG_SUPPORTED
|
|
int "SetAddress() recovery time in ms"
|
|
default 10
|
|
help
|
|
"After successful completion of the Status stage, the device is allowed a SetAddress() recovery
|
|
interval of 2 ms. At the end of this interval, the device must be able to accept Setup packets
|
|
addressed to the new address. Also, at the end of the recovery interval, the device must not respond to
|
|
tokens sent to the old address (unless, of course, the old and new address is the same)." See USB 2.0
|
|
chapter 9.2.6.3 for more details.
|
|
|
|
The default value is set to 10 ms to be safe.
|
|
|
|
|
|
endmenu #Root Hub configuration
|
|
|
|
endmenu #USB-OTG
|