kopia lustrzana https://github.com/espressif/esp-idf
98 wiersze
4.5 KiB
Plaintext
98 wiersze
4.5 KiB
Plaintext
menu "Hardware Settings"
|
|
menu "MAC Config"
|
|
config ESP_MAC_ADDR_UNIVERSE_WIFI_STA
|
|
bool
|
|
|
|
config ESP_MAC_ADDR_UNIVERSE_WIFI_AP
|
|
bool
|
|
|
|
config ESP_MAC_ADDR_UNIVERSE_BT
|
|
bool
|
|
|
|
config ESP_MAC_ADDR_UNIVERSE_ETH
|
|
bool
|
|
|
|
# Insert chip-specific MAC config
|
|
rsource "./port/$IDF_TARGET/Kconfig.mac"
|
|
endmenu
|
|
|
|
menu "Sleep Config"
|
|
# This is here since this option affect behavior of esp_light_sleep_start
|
|
# regardless of power management configuration.
|
|
config ESP_SLEEP_POWER_DOWN_FLASH
|
|
bool "Power down flash in light sleep when there is no SPIRAM"
|
|
depends on !SPIRAM
|
|
default y
|
|
help
|
|
If enabled, chip will try to power down flash as part of esp_light_sleep_start(), which costs
|
|
more time when chip wakes up. Can only be enabled if there is no SPIRAM configured.
|
|
This option will in fact consider VDD_SDIO auto power value (ESP_PD_OPTION_AUTO) as OFF. Also, it is
|
|
possible to force a power domain to stay ON during light sleep by using esp_sleep_pd_config()
|
|
function.
|
|
|
|
config ESP_SLEEP_RTC_BUS_ISO_WORKAROUND
|
|
bool
|
|
default y if IDF_TARGET_ESP32 || IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32S3
|
|
|
|
config ESP_SLEEP_GPIO_RESET_WORKAROUND
|
|
bool "light sleep GPIO reset workaround"
|
|
default y if IDF_TARGET_ESP32C3 || IDF_TARGET_ESP32S3
|
|
select PM_SLP_DISABLE_GPIO if FREERTOS_USE_TICKLESS_IDLE
|
|
help
|
|
esp32c3 and esp32s3 will reset at wake-up if GPIO is received a small electrostatic
|
|
pulse during light sleep, with specific condition
|
|
|
|
- GPIO needs to be configured as input-mode only
|
|
- The pin receives a small electrostatic pulse, and reset occurs when the pulse
|
|
voltage is higher than 6 V
|
|
|
|
For GPIO set to input mode only, it is not a good practice to leave it open/floating,
|
|
The hardware design needs to controlled it with determined supply or ground voltage
|
|
is necessary.
|
|
|
|
This option provides a software workaround for this issue. Configure to isolate all
|
|
GPIO pins in sleep state.
|
|
|
|
config ESP_SLEEP_PSRAM_LEAKAGE_WORKAROUND
|
|
bool "PSRAM leakage current workaround in light sleep"
|
|
depends on SPIRAM
|
|
help
|
|
When the CS pin of SPIRAM is not pulled up, the sleep current will
|
|
increase during light sleep. If the CS pin of SPIRAM has an external
|
|
pull-up, you do not need to select this option, otherwise, you
|
|
should enable this option.
|
|
|
|
config ESP_SLEEP_FLASH_LEAKAGE_WORKAROUND
|
|
bool "Flash leakage current workaround in light sleep"
|
|
help
|
|
When the CS pin of Flash is not pulled up, the sleep current will
|
|
increase during light sleep. If the CS pin of Flash has an external
|
|
pull-up, you do not need to select this option, otherwise, you
|
|
should enable this option.
|
|
endmenu
|
|
|
|
menu "RTC Clock Config"
|
|
# This is used for configure the RTC clock.
|
|
config RTC_CLOCK_BBPLL_POWER_ON_WITH_USB
|
|
bool "Keep BBPLL clock always work"
|
|
depends on ESP_CONSOLE_USB_SERIAL_JTAG || ESP_CONSOLE_SECONDARY_USB_SERIAL_JTAG
|
|
default y
|
|
help
|
|
When the chip goes sleep or software reset, the clock source would change to XTAL
|
|
and switch off the BBPLL clock for saving power. However, this might make the
|
|
USB_SERIAL_JTAG down which depends on BBPLL as its unique clock source.
|
|
Therefore, this is used for keeping bbpll clock always on when USB_SERIAL_JTAG PORT is using.
|
|
If you want to use USB_SERIAL_JTAG under sw_reset case or sleep-wakeup case, you shoule select
|
|
this option. But be aware that this might increase the power consumption.
|
|
endmenu
|
|
|
|
menu "Peripheral Control"
|
|
config PERIPH_CTRL_FUNC_IN_IRAM
|
|
bool "Place peripheral control functions into IRAM"
|
|
default n
|
|
help
|
|
Place peripheral control functions (e.g. periph_module_reset) into IRAM,
|
|
so that these functions can be IRAM-safe and able to be called in the other IRAM interrupt context.
|
|
endmenu
|
|
endmenu
|