esp-idf/components/esp32/Kconfig

555 wiersze
19 KiB
Plaintext

menu "ESP32-specific"
choice ESP32_DEFAULT_CPU_FREQ_MHZ
prompt "CPU frequency"
default ESP32_DEFAULT_CPU_FREQ_240
help
CPU frequency to be set on application startup.
config ESP32_DEFAULT_CPU_FREQ_80
bool "80 MHz"
config ESP32_DEFAULT_CPU_FREQ_160
bool "160 MHz"
config ESP32_DEFAULT_CPU_FREQ_240
bool "240 MHz"
endchoice
config ESP32_DEFAULT_CPU_FREQ_MHZ
int
default 80 if ESP32_DEFAULT_CPU_FREQ_80
default 160 if ESP32_DEFAULT_CPU_FREQ_160
default 240 if ESP32_DEFAULT_CPU_FREQ_240
config MEMMAP_SMP
bool "Reserve memory for two cores"
default "y"
help
The ESP32 contains two cores. If you plan to only use one, you can disable this item
to save some memory. (ToDo: Make this automatically depend on unicore support)
config MEMMAP_TRACEMEM
bool "Use TRAX tracing feature"
default "n"
help
The ESP32 contains a feature which allows you to trace the execution path the processor
has taken through the program. This is stored in a chunk of 32K (16K for single-processor)
of memory that can't be used for general purposes anymore. Disable this if you do not know
what this is.
config MEMMAP_TRACEMEM_TWOBANKS
bool "Reserve memory for tracing both pro as well as app cpu execution"
default "n"
depends on MEMMAP_TRACEMEM && MEMMAP_SMP
help
The ESP32 contains a feature which allows you to trace the execution path the processor
has taken through the program. This is stored in a chunk of 32K (16K for single-processor)
of memory that can't be used for general purposes anymore. Disable this if you do not know
what this is.
# Memory to reverse for trace, used in linker script
config TRACEMEM_RESERVE_DRAM
hex
default 0x8000 if MEMMAP_TRACEMEM && MEMMAP_TRACEMEM_TWOBANKS
default 0x4000 if MEMMAP_TRACEMEM && !MEMMAP_TRACEMEM_TWOBANKS
default 0x0
choice ESP32_COREDUMP_TO_FLASH_OR_UART
prompt "Core dump destination"
default ESP32_ENABLE_COREDUMP_TO_NONE
help
Select place to store core dump: flash, uart or none (to disable core dumps generation).
If core dump is configured to be stored in flash and custom partition table is used add
corresponding entry to your CSV. For examples, please see predefined partition table CSV descriptions
in the components/partition_table directory.
config ESP32_ENABLE_COREDUMP_TO_FLASH
bool "Flash"
select ESP32_ENABLE_COREDUMP
config ESP32_ENABLE_COREDUMP_TO_UART
bool "UART"
select ESP32_ENABLE_COREDUMP
config ESP32_ENABLE_COREDUMP_TO_NONE
bool "None"
endchoice
config ESP32_ENABLE_COREDUMP
bool
default F
help
Enables/disable core dump module.
config ESP32_CORE_DUMP_UART_DELAY
int "Core dump print to UART delay"
depends on ESP32_ENABLE_COREDUMP_TO_UART
default 0
help
Config delay (in ms) before printing core dump to UART.
Delay can be interrupted by pressing Enter key.
config ESP32_CORE_DUMP_LOG_LEVEL
int "Core dump module logging level"
depends on ESP32_ENABLE_COREDUMP
default 1
help
Config core dump module logging level (0-5).
# Not implemented and/or needs new silicon rev to work
config MEMMAP_SPISRAM
bool "Use external SPI SRAM chip as main memory"
depends on ESP32_NEEDS_NEW_SILICON_REV
default "n"
help
The ESP32 can control an external SPI SRAM chip, adding the memory it contains to the
main memory map. Enable this if you have this hardware and want to use it in the same
way as on-chip RAM.
config SYSTEM_EVENT_QUEUE_SIZE
int "System event queue size"
default 32
help
Config system event queue size in different application.
config SYSTEM_EVENT_TASK_STACK_SIZE
int "Event loop task stack size"
default 4096
help
Config system event task stack size in different application.
config MAIN_TASK_STACK_SIZE
int "Main task stack size"
default 4096
help
Config system event task stack size in different application.
config NEWLIB_STDOUT_ADDCR
bool "Standard-out output adds carriage return before newline"
default y
help
Most people are used to end their printf strings with a newline. If this
is sent as is to the serial port, most terminal programs will only move the
cursor one line down, not also move it to the beginning of the line. This
is usually done by an added CR character. Enabling this will make the
standard output code automatically add a CR character before a LF.
With this option enabled, C standard library functions which read from UART
(like scanf) will convert "\r\n" character sequences back to "\n".
This option doesn't affect behavior of the UART driver (drivers/uart.h).
config NEWLIB_NANO_FORMAT
bool "Enable 'nano' formatting options for printf/scanf family"
default n
help
ESP32 ROM contains parts of newlib C library, including printf/scanf family
of functions. These functions have been compiled with so-called "nano"
formatting option. This option doesn't support 64-bit integer formats and C99
features, such as positional arguments.
For more details about "nano" formatting option, please see newlib readme file,
search for '--enable-newlib-nano-formatted-io':
https://sourceware.org/newlib/README
If this option is enabled, build system will use functions available in
ROM, reducing the application binary size. Functions available in ROM run
faster than functions which run from flash. Functions available in ROM can
also run when flash instruction cache is disabled.
If you need 64-bit integer formatting support or C99 features, keep this
option disabled.
choice CONSOLE_UART
prompt "UART for console output"
default CONSOLE_UART_DEFAULT
help
Select whether to use UART for console output (through stdout and stderr).
- Default is to use UART0 on pins GPIO1(TX) and GPIO3(RX).
- If "Custom" is selected, UART0 or UART1 can be chosen,
and any pins can be selected.
- If "None" is selected, there will be no console output on any UART, except
for initial output from ROM bootloader. This output can be further suppressed by
bootstrapping GPIO13 pin to low logic level.
config CONSOLE_UART_DEFAULT
bool "Default: UART0, TX=GPIO1, RX=GPIO3"
config CONSOLE_UART_CUSTOM
bool "Custom"
config CONSOLE_UART_NONE
bool "None"
endchoice
choice CONSOLE_UART_NUM
prompt "UART peripheral to use for console output (0-1)"
depends on CONSOLE_UART_CUSTOM
default CONSOLE_UART_CUSTOM_NUM_0
help
Due of a ROM bug, UART2 is not supported for console output
via ets_printf.
config CONSOLE_UART_CUSTOM_NUM_0
bool "UART0"
config CONSOLE_UART_CUSTOM_NUM_1
bool "UART1"
endchoice
config CONSOLE_UART_NUM
int
default 0 if CONSOLE_UART_DEFAULT || CONSOLE_UART_NONE
default 0 if CONSOLE_UART_CUSTOM_NUM_0
default 1 if CONSOLE_UART_CUSTOM_NUM_1
config CONSOLE_UART_TX_GPIO
int "UART TX on GPIO#"
depends on CONSOLE_UART_CUSTOM
range 0 33
default 19
config CONSOLE_UART_RX_GPIO
int "UART RX on GPIO#"
depends on CONSOLE_UART_CUSTOM
range 0 39
default 21
config CONSOLE_UART_BAUDRATE
int "UART console baud rate"
depends on !CONSOLE_UART_NONE
default 115200
range 1200 4000000
config ULP_COPROC_ENABLED
bool "Enable Ultra Low Power (ULP) Coprocessor"
default "n"
help
Set to 'y' if you plan to load a firmware for the coprocessor.
If this option is enabled, further coprocessor configuration will appear in the Components menu.
config ULP_COPROC_RESERVE_MEM
int "RTC slow memory reserved for coprocessor"
default 512
range 32 8192
depends on ULP_COPROC_ENABLED
help
Bytes of memory to reserve for ULP coprocessor firmware & data.
Data is reserved at the beginning of RTC slow memory.
# Set CONFIG_ULP_COPROC_RESERVE_MEM to 0 if ULP is disabled
config ULP_COPROC_RESERVE_MEM
int
default 0
depends on !ULP_COPROC_ENABLED
choice ESP32_PANIC
prompt "Panic handler behaviour"
default ESP32_PANIC_PRINT_REBOOT
help
If FreeRTOS detects unexpected behaviour or an unhandled exception, the panic handler is
invoked. Configure the panic handlers action here.
config ESP32_PANIC_PRINT_HALT
bool "Print registers and halt"
help
Outputs the relevant registers over the serial port and halt the
processor. Needs a manual reset to restart.
config ESP32_PANIC_PRINT_REBOOT
bool "Print registers and reboot"
help
Outputs the relevant registers over the serial port and immediately
reset the processor.
config ESP32_PANIC_SILENT_REBOOT
bool "Silent reboot"
help
Just resets the processor without outputting anything
config ESP32_PANIC_GDBSTUB
bool "Invoke GDBStub"
help
Invoke gdbstub on the serial port, allowing for gdb to attach to it to do a postmortem
of the crash.
endchoice
config ESP32_DEBUG_OCDAWARE
bool "Make exception and panic handlers JTAG/OCD aware"
default y
help
The FreeRTOS panic and unhandled exception handers can detect a JTAG OCD debugger and
instead of panicking, have the debugger stop on the offending instruction.
config INT_WDT
bool "Interrupt watchdog"
default y
help
This watchdog timer can detect if the FreeRTOS tick interrupt has not been called for a certain time,
either because a task turned off interrupts and did not turn them on for a long time, or because an
interrupt handler did not return. It will try to invoke the panic handler first and failing that
reset the SoC.
config INT_WDT_TIMEOUT_MS
int "Interrupt watchdog timeout (ms)"
depends on INT_WDT
default 300
range 10 10000
help
The timeout of the watchdog, in miliseconds. Make this higher than the FreeRTOS tick rate.
config INT_WDT_CHECK_CPU1
bool "Also watch CPU1 tick interrupt"
depends on INT_WDT && !FREERTOS_UNICORE
default y
help
Also detect if interrupts on CPU 1 are disabled for too long.
config TASK_WDT
bool "Task watchdog"
default y
help
This watchdog timer can be used to make sure individual tasks are still running.
config TASK_WDT_PANIC
bool "Invoke panic handler when Task Watchdog is triggered"
depends on TASK_WDT
default n
help
Normally, the Task Watchdog will only print out a warning if it detects it has not
been fed. If this is enabled, it will invoke the panic handler instead, which
can then halt or reboot the chip.
config TASK_WDT_TIMEOUT_S
int "Task watchdog timeout (seconds)"
depends on TASK_WDT
range 1 60
default 5
help
Timeout for the task WDT, in seconds.
config TASK_WDT_CHECK_IDLE_TASK
bool "Task watchdog watches CPU0 idle task"
depends on TASK_WDT
default y
help
With this turned on, the task WDT can detect if the idle task is not called within the task
watchdog timeout period. The idle task not being called usually is a symptom of another
task hoarding the CPU. It is also a bad thing because FreeRTOS household tasks depend on the
idle task getting some runtime every now and then. Take Care: With this disabled, this
watchdog will trigger if no tasks register themselves within the timeout value.
config TASK_WDT_CHECK_IDLE_TASK_CPU1
bool "Task watchdog also watches CPU1 idle task"
depends on TASK_WDT_CHECK_IDLE_TASK && !FREERTOS_UNICORE
default y
help
Also check the idle task that runs on CPU1.
#The brownout detector code is disabled (by making it depend on a nonexisting symbol) because the current revision of ESP32
#silicon has a bug in the brown-out detector, rendering it unusable for resetting the CPU.
config BROWNOUT_DET
bool "Hardware brownout detect & reset"
default y
depends on NEEDS_ESP32_NEW_SILICON_REV
help
The ESP32 has a built-in brownout detector which can detect if the voltage is lower than
a specific value. If this happens, it will reset the chip in order to prevent unintended
behaviour.
choice BROWNOUT_DET_LVL_SEL
prompt "Brownout voltage level"
depends on BROWNOUT_DET
default BROWNOUT_DET_LVL_SEL_25
help
The brownout detector will reset the chip when the supply voltage is below this level.
#The voltage levels here are estimates, more work needs to be done to figure out the exact voltages
#of the brownout threshold levels.
config BROWNOUT_DET_LVL_SEL_0
bool "2.1V"
config BROWNOUT_DET_LVL_SEL_1
bool "2.2V"
config BROWNOUT_DET_LVL_SEL_2
bool "2.3V"
config BROWNOUT_DET_LVL_SEL_3
bool "2.4V"
config BROWNOUT_DET_LVL_SEL_4
bool "2.5V"
config BROWNOUT_DET_LVL_SEL_5
bool "2.6V"
config BROWNOUT_DET_LVL_SEL_6
bool "2.7V"
config BROWNOUT_DET_LVL_SEL_7
bool "2.8V"
endchoice
config BROWNOUT_DET_LVL
int
default 0 if BROWNOUT_DET_LVL_SEL_0
default 1 if BROWNOUT_DET_LVL_SEL_1
default 2 if BROWNOUT_DET_LVL_SEL_2
default 3 if BROWNOUT_DET_LVL_SEL_3
default 4 if BROWNOUT_DET_LVL_SEL_4
default 5 if BROWNOUT_DET_LVL_SEL_5
default 6 if BROWNOUT_DET_LVL_SEL_6
default 7 if BROWNOUT_DET_LVL_SEL_7
config BROWNOUT_DET_RESETDELAY
int "Brownout reset delay (in uS)"
depends on BROWNOUT_DET
range 0 6820
default 1000
help
The brownout detector can reset the chip after a certain delay, in order to make sure e.g. a voltage dip has entirely passed
before trying to restart the chip. You can set the delay here.
choice ESP32_TIME_SYSCALL
prompt "Timers used for gettimeofday function"
default ESP32_TIME_SYSCALL_USE_RTC_FRC1
help
This setting defines which hardware timers are used to
implement 'gettimeofday' and 'time' functions in C library.
- If only FRC1 timer is used, gettimeofday will provide time at
microsecond resolution. Time will not be preserved when going
into deep sleep mode.
- If both FRC1 and RTC timers are used, timekeeping will
continue in deep sleep. Time will be reported at 1 microsecond
resolution.
- If only RTC timer is used, timekeeping will continue in
deep sleep, but time will be measured at 6.(6) microsecond
resolution. Also the gettimeofday function itself may take
longer to run.
- If no timers are used, gettimeofday and time functions
return -1 and set errno to ENOSYS.
- When RTC is used for timekeeping, two RTC_STORE registers are
used to keep time in deep sleep mode.
config ESP32_TIME_SYSCALL_USE_RTC
bool "RTC"
config ESP32_TIME_SYSCALL_USE_RTC_FRC1
bool "RTC and FRC1"
config ESP32_TIME_SYSCALL_USE_FRC1
bool "FRC1"
config ESP32_TIME_SYSCALL_USE_NONE
bool "None"
endchoice
choice ESP32_RTC_CLOCK_SOURCE
prompt "RTC clock source"
default ESP32_RTC_CLOCK_SOURCE_INTERNAL_RC
help
Choose which clock is used as RTC clock source.
The only available option for now is to use internal
150kHz RC oscillator.
config ESP32_RTC_CLOCK_SOURCE_INTERNAL_RC
bool "Internal RC"
config ESP32_RTC_CLOCK_SOURCE_EXTERNAL_CRYSTAL
bool "External 32kHz crystal"
depends on DOCUMENTATION_FOR_RTC_CNTL
endchoice
config ESP32_DEEP_SLEEP_WAKEUP_DELAY
int "Extra delay in deep sleep wake stub (in us)"
default 0
range 0 5000
help
When ESP32 exits deep sleep, the CPU and the flash chip are powered on
at the same time. CPU will run deep sleep stub first, and then
proceed to load code from flash. Some flash chips need sufficient
time to pass between power on and first read operation. By default,
without any extra delay, this time is approximately 900us.
If you are using a flash chip which needs more than 900us to become
ready after power on, set this parameter to add extra delay
to the default deep sleep stub.
If you are seeing "flash read err, 1000" message printed to the
console after deep sleep reset, try increasing this value.
endmenu
menuconfig WIFI_ENABLED
bool "WiFi"
default y
help
Select this option to enable WiFi stack and show the submenu with WiFi configuration choices.
config SW_COEXIST_ENABLE
bool "Software controls WiFi/Bluetooth coexistence"
depends on WIFI_ENABLED && BT_ENABLED
default n
help
If enabled, WiFi & Bluetooth coexistence is controlled by software rather than hardware.
Recommended for heavy traffic scenarios. Both coexistence configuration options are
automatically managed, no user intervention is required.
config ESP32_WIFI_RX_BUFFER_NUM
int "Max number of WiFi RX buffers"
depends on WIFI_ENABLED
range 2 25
default 10
help
Set the number of WiFi rx buffers. Each buffer takes approximately 1.6KB of RAM.
Larger number for higher throughput but more memory. Smaller number for lower
throughput but less memory.
config PHY_ENABLED
bool
default y if WIFI_ENABLED || BT_ENABLED
menu PHY
visible if PHY_ENABLED
config ESP32_PHY_CALIBRATION_AND_DATA_STORAGE
bool "Do phy calibration and store calibration data in NVS"
depends on PHY_ENABLED
default y
help
If this option is enabled, NVS will be initialized and calibration data will be loaded from there.
PHY calibration will be skipped on deep sleep wakeup. If calibration data is not found, full calibration
will be performed and stored in NVS. In all other cases, only partial calibration will be performed.
If unsure, choose 'y'.
config ESP32_PHY_INIT_DATA_IN_PARTITION
bool "Use a partition to store PHY init data"
depends on PHY_ENABLED
default n
help
If enabled, PHY init data will be loaded from a partition.
When using a custom partition table, make sure that PHY data
partition is included (type: 'data', subtype: 'phy').
With default partition tables, this is done automatically.
If PHY init data is stored in a partition, it has to be flashed there,
otherwise runtime error will occur.
If this option is not enabled, PHY init data will be embedded
into the application binary.
If unsure, choose 'n'.
config ESP32_PHY_MAX_WIFI_TX_POWER
int "Max WiFi TX power (dBm)"
range 0 20
default 20
depends on PHY_ENABLED && WIFI_ENABLED
help
Set maximum transmit power for WiFi radio. Actual transmit power for high
data rates may be lower than this setting.
config ESP32_PHY_MAX_TX_POWER
int
depends on PHY_ENABLED
default 20 if !WIFI_ENABLED
default ESP32_PHY_MAX_WIFI_TX_POWER if WIFI_ENABLED
endmenu