b4fe434d2e
fix(wifi): fix esp_wifi_scan_start memory leakage issue Closes IDFGH-9313 See merge request espressif/esp-idf!28869 |
||
---|---|---|
.. | ||
main | ||
CMakeLists.txt | ||
README.md | ||
pytest_iperf.py | ||
sdkconfig.ci.99 | ||
sdkconfig.defaults | ||
sdkconfig.defaults.esp32 | ||
sdkconfig.defaults.esp32c2 | ||
sdkconfig.defaults.esp32c3 | ||
sdkconfig.defaults.esp32c6 | ||
sdkconfig.defaults.esp32s2 | ||
sdkconfig.defaults.esp32s3 |
README.md
Supported Targets | ESP32 | ESP32-C2 | ESP32-C3 | ESP32-C6 | ESP32-S2 | ESP32-S3 |
---|
Iperf Example
Note about iperf version
The iperf example doesn't support all features in standard iperf. It's compitable with iperf version 2.x.
Note about 80MHz flash frequency
The iperf can get better throughput if the SPI flash frequency is set to 80MHz, but the system may crash in 80MHz mode for ESP-WROVER-KIT. Removing R140~R145 from the board can fix this issue. Currently the default SPI frequency is set to 40MHz, if you want to change the SPI flash frequency to 80MHz, please make sure R140~R145 are removed from ESP-WROVER-KIT or use ESP32 DevKitC.
Introduction
This example implements the protocol used by the common performance measurement tool iPerf. Performance can be measured between two ESP32s running this example, or between a single ESP32 and a computer running the iPerf tool
Demo steps to test station TCP Tx performance:
-
Configure in
menuconfig
which serial output you are using. Executeidf.py menuconfig
and go toComponent config/ESP System Settings/Channel for console output
, then select the appropiate interface. By default the UART0 interface is used, this means that for example in the ESP32-S3-DevKitC-1 or ESP32-C6-DevKitC-1 you should connect to the micro-usb connector labeled as UART and not to the one labeled as USB. To use the one labeled as USB you should change the aforementioned setting toUSB Serial/JTAG Controller
. -
Build the iperf example with sdkconfig.defaults, which contains performance test specific configurations
-
Run the demo as station mode and join the target AP sta ssid password
-
Run iperf as server on AP side iperf -s -i 3
-
Run iperf as client on ESP32 side iperf -c 192.168.10.42 -i 3 -t 60
The console output, which is printed by station TCP RX throughput test, looks like:
iperf> sta aptest
I (5325) iperf: sta connecting to 'aptest'
iperf> I (6017) event: ip: 192.168.10.248, mask: 255.255.255.0, gw: 192.168.10.1
iperf> iperf -s -i 3 -t 1000
I (14958) iperf: mode=tcp-server sip=192.168.10.248:5001, dip=0.0.0.0:5001, interval=3, time=1000
Interval Bandwidth
iperf> accept: 192.168.10.42,62958
0- 3 sec 8.43 Mbits/sec
3- 6 sec 36.16 Mbits/sec
6- 9 sec 36.22 Mbits/sec
9- 12 sec 36.44 Mbits/sec
12- 15 sec 36.25 Mbits/sec
15- 18 sec 24.36 Mbits/sec
18- 21 sec 27.79 Mbits/sec
Steps to test station/soft-AP TCP/UDP RX/TX throughput are similar as test steps in station TCP TX.
See the README.md file in the upper level 'examples' directory for more information about examples.