kopia lustrzana https://github.com/espressif/esp-idf
91 wiersze
2.4 KiB
C
91 wiersze
2.4 KiB
C
/*
|
|
* SPDX-FileCopyrightText: 2021-2022 Espressif Systems (Shanghai) CO LTD
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
#pragma once
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
#include <inttypes.h>
|
|
#include "driver/uart.h"
|
|
|
|
/**
|
|
* Function prototype for UART driver to ask for more data to send.
|
|
* Returns -1 if no more data is available for TX.
|
|
* Driver must call this with interrupts disabled.
|
|
*/
|
|
typedef int (*hci_uart_tx_char)(void *arg);
|
|
|
|
/**
|
|
* Function prototype for UART driver to report that transmission is
|
|
* complete. This should be called when transmission of last byte is
|
|
* finished.
|
|
* Driver must call this with interrupts disabled.
|
|
*/
|
|
typedef void (*hci_uart_tx_done)(void *arg);
|
|
|
|
/**
|
|
* Function prototype for UART driver to report incoming byte of data.
|
|
* Returns -1 if data was dropped.
|
|
* Driver must call this with interrupts disabled.
|
|
*/
|
|
typedef int (*hci_uart_rx_char)(void *arg, uint8_t byte);
|
|
|
|
|
|
/**
|
|
* Initializes given uart. Mapping of logical UART number to physical
|
|
* UART/GPIO pins is in BSP.
|
|
*/
|
|
int hci_uart_init_cbs(int uart, hci_uart_tx_char tx_func,
|
|
hci_uart_tx_done tx_done, hci_uart_rx_char rx_func, void *arg);
|
|
|
|
|
|
/**
|
|
* Applies given configuration to UART.
|
|
*
|
|
* @param port_num The UART number to configure
|
|
* @param speed The baudrate in bps to configure
|
|
* @param databits The number of databits to send per byte
|
|
* @param stopbits The number of stop bits to send
|
|
* @param parity The UART parity
|
|
* @param flow_ctl Flow control settings on the UART
|
|
*
|
|
* @return 0 on success, non-zero error code on failure
|
|
*/
|
|
int hci_uart_config(int port_num, int32_t baud_rate, uint8_t data_bits, uint8_t stop_bits,
|
|
uart_parity_t parity, uart_hw_flowcontrol_t flow_ctl);
|
|
|
|
/**
|
|
* Close UART port. Can call hal_uart_config() with different settings after
|
|
* calling this.
|
|
*
|
|
* @param port_num The UART number to close
|
|
*/
|
|
int hci_uart_close(int port_num);
|
|
|
|
/**
|
|
* More data queued for transmission. UART driver will start asking for that
|
|
* data.
|
|
*
|
|
* @param port_num The UART number to start TX on
|
|
*/
|
|
void hci_uart_start_tx(int port_num);
|
|
|
|
/**
|
|
* Upper layers have consumed some data, and are now ready to receive more.
|
|
* This is meaningful after uart_rx_char callback has returned -1 telling
|
|
* that no more data can be accepted.
|
|
*
|
|
* @param port_num The UART number to begin RX on
|
|
*/
|
|
void hci_uart_start_rx(int port_num);
|
|
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|