kopia lustrzana https://github.com/espressif/esp-idf
78 wiersze
2.9 KiB
ReStructuredText
78 wiersze
2.9 KiB
ReStructuredText
***************************************
|
|
Building OpenOCD from Sources for Linux
|
|
***************************************
|
|
|
|
:link_to_translation:`zh_CN:[中文]`
|
|
|
|
The following instructions are alternative to downloading binary OpenOCD from `Espressif GitHub <https://github.com/espressif/openocd-esp32/releases>`_. To quickly setup the binary OpenOCD, instead of compiling it yourself, backup and proceed to section :ref:`jtag-debugging-setup-openocd`.
|
|
|
|
|
|
.. highlight:: bash
|
|
|
|
Download Sources of OpenOCD
|
|
===========================
|
|
|
|
The sources for the {IDF_TARGET_NAME}-enabled variant of OpenOCD are available from Espressif GitHub under https://github.com/espressif/openocd-esp32. To download the sources, use the following commands::
|
|
|
|
cd ~/esp
|
|
git clone --recursive https://github.com/espressif/openocd-esp32.git
|
|
|
|
The clone of sources should be now saved in ``~/esp/openocd-esp32`` directory.
|
|
|
|
|
|
Install Dependencies
|
|
====================
|
|
|
|
Install packages that are required to compile OpenOCD.
|
|
|
|
.. note::
|
|
|
|
Install the following packages one by one, check if installation was successful and then proceed to the next package. Resolve reported problems before moving to the next step.
|
|
|
|
::
|
|
|
|
sudo apt-get install make
|
|
sudo apt-get install libtool
|
|
sudo apt-get install pkg-config
|
|
sudo apt-get install autoconf
|
|
sudo apt-get install automake
|
|
sudo apt-get install texinfo
|
|
sudo apt-get install libusb-1.0
|
|
|
|
.. note::
|
|
|
|
* Version of pkg-config should be 0.2.3 or above.
|
|
* Version of autoconf should be 2.6.4 or above.
|
|
* Version of automake should be 1.9 or above.
|
|
* When using USB-Blaster, ASIX Presto, OpenJTAG and FT2232 as adapters, drivers libFTDI and FTD2XX need to be downloaded and installed.
|
|
* When using CMSIS-DAP, HIDAPI is needed.
|
|
|
|
|
|
Build OpenOCD
|
|
=============
|
|
|
|
Proceed with configuring and building OpenOCD::
|
|
|
|
cd ~/esp/openocd-esp32
|
|
./bootstrap
|
|
./configure
|
|
make
|
|
|
|
Optionally you can add ``sudo make install`` step at the end. Skip it, if you have an existing OpenOCD (from e.g., another development platform), as it may get overwritten.
|
|
|
|
.. note::
|
|
|
|
* Should an error occur, resolve it and try again until the command ``make`` works.
|
|
* If there is a submodule problem from OpenOCD, please ``cd`` to the ``openocd-esp32`` directory and input ``git submodule update --init``.
|
|
* If the ``./configure`` is successfully run, information of enabled JTAG will be printed under ``OpenOCD configuration summary``.
|
|
* If the information of your device is not shown in the log, use ``./configure`` to enable it as described in ``../openocd-esp32/doc/INSTALL.txt``.
|
|
* For details concerning compiling OpenOCD, please refer to ``openocd-esp32/README``.
|
|
|
|
Once ``make`` process is successfully completed, the executable of OpenOCD will be saved in ``~/openocd-esp32/bin`` directory.
|
|
|
|
|
|
Next Steps
|
|
==========
|
|
|
|
To carry on with debugging environment setup, proceed to section :ref:`jtag-debugging-configuring-target`.
|