280d39aedd
bugfix(i2s): allow to use apll in pdm/adc/dac mode See merge request idf/esp-idf!3800 |
||
---|---|---|
.. | ||
main | ||
tools | ||
CMakeLists.txt | ||
Makefile | ||
README.md | ||
partitions_adc_dac_example.csv |
README.md
I2S Built-in ADC/DAC Example
(See the README.md file in the upper level 'examples' directory for more information about examples.)
In this example, we configure I2S to work in I2S_ADC and I2S_DAC modes and then:
- recording sound from ADC,
- playing the recorded sound,
- playing an audio file in flash via DAC.
Note:
The tools
directory contains generate_audio_file.py
script for generating audio files:
* The script provides an example of generating audio tables from `.wav` files.
* In this example, the `wav` file must be in 16k/16bit mono format.
* The script will bundle the `wav` files into a single table named `audio_example_file.h`.
* Since the ADC can only play 8-bit data, the script will scale each 16-bit value to a 8-bit value.
* The script will covert all signed values into unsigned values because only positive values will be output by the ADC.
How to Use Example
Hardware Required
- A development board with ESP32 SoC (e.g., ESP32-DevKitC, ESP-WROVER-KIT, etc.)
- A USB cable for power supply and programming
- A microphone (with amplifier) and one or two speaker(s) for testing.
The following is the hardware connection:
hardware | module | GPIO |
---|---|---|
Microphone | ADC1_CH0 | GPIO36 |
speaker(R) | DAC1 | GPIO25 |
speaker(L) | DAC2 | GPIO26 |
Configure the Project
make menuconfig
- Set serial port under Serial Flasher Options, the flash size should be set to 4 MB.
- Select "Custom partition table CSV" and rename "Custom partition CSV file" to "partitions_adc_dac_example.csv".
(Note that you can use sdkconfig.defaults
)
Build and Flash
Build the project and flash it to the board, then run monitor tool to view serial output:
make -j4 flash monitor
(To exit the serial monitor, type Ctrl-]
.)
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
Example Output
Reset your development board. The application it will first record the sound through the microphone. Then it will play the recorded sound, and finally a piece of audio stored in the flash. The following is the output log:
partiton addr: 0x00110000; size: 2097152; label: storage
Erasing flash
partiton addr: 0x00110000; size: 2097152; label: storage
Erase size: 323584 Bytes
I2S: PLL_D2: Req RATE: 16000, real rate: 1004.000, BITS: 16, CLKM: 83, BCK: 60, MCLK: 83.333, SCLK: 32128.000000, diva: 64, divb: 21
Sound recording 5%
Sound recording 10%
...
Sound recording 97%
Sound recording 102%
playing: 0 %
playing: 1 %
playing: 2 %
...
playing: 96 %
playing: 97 %
playing: 98 %
Playing file example:
I2S: PLL_D2: Req RATE: 16000, real rate: 1004.000, BITS: 16, CLKM: 83, BCK: 60, MCLK: 83.333, SCLK: 32128.000000, diva: 64, divb: 21
Troubleshooting
-
Program upload failure
- Hardware connection is not correct: run
make monitor
, and reboot your board to see if there are any output logs. - The baud rate for downloading is too high: lower your baud rate in the
menuconfig
menu, and try again.
- Hardware connection is not correct: run
For any technical queries, please open an issue on GitHub. We will get back to you soon.