esp-idf/components/esp32/include/soc/uhci_struct.h

338 wiersze
22 KiB
C
Czysty Wina Historia

This file contains ambiguous Unicode characters!

This file contains ambiguous Unicode characters that may be confused with others in your current locale. If your use case is intentional and legitimate, you can safely ignore this warning. Use the Escape button to highlight these characters.

// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#ifndef _SOC_UHCI_STRUCT_H_
#define _SOC_UHCI_STRUCT_H_
typedef volatile struct {
union {
struct {
uint32_t in_rst: 1; /*Set this bit to reset in link operations.*/
uint32_t out_rst: 1; /*Set this bit to reset out link operations.*/
uint32_t ahbm_fifo_rst: 1; /*Set this bit to reset dma ahb fifo.*/
uint32_t ahbm_rst: 1; /*Set this bit to reset dma ahb interface.*/
uint32_t in_loop_test: 1; /*Set this bit to enable loop test for in links.*/
uint32_t out_loop_test: 1; /*Set this bit to enable loop test for out links.*/
uint32_t out_auto_wrback: 1; /*when in link's length is 0 go on to use the next in link automatically.*/
uint32_t out_no_restart_clr: 1; /*don't use*/
uint32_t out_eof_mode: 1; /*Set this bit to produce eof after DMA pops all data clear this bit to produce eof after DMA pushes all data*/
uint32_t uart0_ce: 1; /*Set this bit to use UART to transmit or receive data.*/
uint32_t uart1_ce: 1; /*Set this bit to use UART1 to transmit or receive data.*/
uint32_t uart2_ce: 1; /*Set this bit to use UART2 to transmit or receive data.*/
uint32_t outdscr_burst_en: 1; /*Set this bit to enable DMA in links to use burst mode.*/
uint32_t indscr_burst_en: 1; /*Set this bit to enable DMA out links to use burst mode.*/
uint32_t out_data_burst_en: 1; /*Set this bit to enable DMA burst MODE*/
uint32_t mem_trans_en: 1;
uint32_t seper_en: 1; /*Set this bit to use special char to separate the data frame.*/
uint32_t head_en: 1; /*Set this bit to enable to use head packet before the data frame.*/
uint32_t crc_rec_en: 1; /*Set this bit to enable receiver''s ability of crc calculation when crc_en bit in head packet is 1 then there will be crc bytes after data_frame*/
uint32_t uart_idle_eof_en: 1; /*Set this bit to enable to use idle time when the idle time after data frame is satisfied this means the end of a data frame.*/
uint32_t len_eof_en: 1; /*Set this bit to enable to use packet_len in packet head when the received data is equal to packet_len this means the end of a data frame.*/
uint32_t encode_crc_en: 1; /*Set this bit to enable crc calculation for data frame when bit6 in the head packet is 1.*/
uint32_t clk_en: 1; /*Set this bit to enable clock-gating for read or write registers.*/
uint32_t uart_rx_brk_eof_en: 1; /*Set this bit to enable to use brk char as the end of a data frame.*/
uint32_t reserved24: 8;
};
uint32_t val;
} conf0;
union {
struct {
uint32_t rx_start: 1; /*when a separator char has been send it will produce uhci_rx_start_int interrupt.*/
uint32_t tx_start: 1; /*when DMA detects a separator char it will produce uhci_tx_start_int interrupt.*/
uint32_t rx_hung: 1; /*when DMA takes a lot of time to receive a data it will produce uhci_rx_hung_int interrupt.*/
uint32_t tx_hung: 1; /*when DMA takes a lot of time to read a data from RAM it will produce uhci_tx_hung_int interrupt.*/
uint32_t in_done: 1; /*when a in link descriptor has been completed it will produce uhci_in_done_int interrupt.*/
uint32_t in_suc_eof: 1; /*when a data packet has been received it will produce uhci_in_suc_eof_int interrupt.*/
uint32_t in_err_eof: 1; /*when there are some errors about eof in in link descriptor it will produce uhci_in_err_eof_int interrupt.*/
uint32_t out_done: 1; /*when a out link descriptor is completed it will produce uhci_out_done_int interrupt.*/
uint32_t out_eof: 1; /*when the current descriptor's eof bit is 1 it will produce uhci_out_eof_int interrupt.*/
uint32_t in_dscr_err: 1; /*when there are some errors about the out link descriptor it will produce uhci_in_dscr_err_int interrupt.*/
uint32_t out_dscr_err: 1; /*when there are some errors about the in link descriptor it will produce uhci_out_dscr_err_int interrupt.*/
uint32_t in_dscr_empty: 1; /*when there are not enough in links for DMA it will produce uhci_in_dscr_err_int interrupt.*/
uint32_t outlink_eof_err: 1; /*when there are some errors about eof in outlink descriptor it will produce uhci_outlink_eof_err_int interrupt.*/
uint32_t out_total_eof: 1; /*When all data have been send it will produce uhci_out_total_eof_int interrupt.*/
uint32_t send_s_q: 1; /*When use single send registers to send a short packets it will produce this interrupt when dma has send the short packet.*/
uint32_t send_a_q: 1; /*When use always_send registers to send a series of short packets it will produce this interrupt when dma has send the short packet.*/
uint32_t dma_in_fifo_full_wm: 1;
uint32_t reserved17: 15;
};
uint32_t val;
} int_raw;
union {
struct {
uint32_t rx_start: 1;
uint32_t tx_start: 1;
uint32_t rx_hung: 1;
uint32_t tx_hung: 1;
uint32_t in_done: 1;
uint32_t in_suc_eof: 1;
uint32_t in_err_eof: 1;
uint32_t out_done: 1;
uint32_t out_eof: 1;
uint32_t in_dscr_err: 1;
uint32_t out_dscr_err: 1;
uint32_t in_dscr_empty: 1;
uint32_t outlink_eof_err: 1;
uint32_t out_total_eof: 1;
uint32_t send_s_q: 1;
uint32_t send_a_q: 1;
uint32_t dma_in_fifo_full_wm: 1;
uint32_t reserved17: 15;
};
uint32_t val;
} int_st;
union {
struct {
uint32_t rx_start: 1;
uint32_t tx_start: 1;
uint32_t rx_hung: 1;
uint32_t tx_hung: 1;
uint32_t in_done: 1;
uint32_t in_suc_eof: 1;
uint32_t in_err_eof: 1;
uint32_t out_done: 1;
uint32_t out_eof: 1;
uint32_t in_dscr_err: 1;
uint32_t out_dscr_err: 1;
uint32_t in_dscr_empty: 1;
uint32_t outlink_eof_err: 1;
uint32_t out_total_eof: 1;
uint32_t send_s_q: 1;
uint32_t send_a_q: 1;
uint32_t dma_in_fifo_full_wm: 1;
uint32_t reserved17: 15;
};
uint32_t val;
} int_ena;
union {
struct {
uint32_t rx_start: 1;
uint32_t tx_start: 1;
uint32_t rx_hung: 1;
uint32_t tx_hung: 1;
uint32_t in_done: 1;
uint32_t in_suc_eof: 1;
uint32_t in_err_eof: 1;
uint32_t out_done: 1;
uint32_t out_eof: 1;
uint32_t in_dscr_err: 1;
uint32_t out_dscr_err: 1;
uint32_t in_dscr_empty: 1;
uint32_t outlink_eof_err: 1;
uint32_t out_total_eof: 1;
uint32_t send_s_q: 1;
uint32_t send_a_q: 1;
uint32_t dma_in_fifo_full_wm: 1;
uint32_t reserved17: 15;
};
uint32_t val;
} int_clr;
union {
struct {
uint32_t full: 1; /*1:DMA out link descriptor's fifo is full.*/
uint32_t empty: 1; /*1:DMA in link descriptor's fifo is empty.*/
uint32_t reserved2: 30;
};
uint32_t val;
} dma_out_status;
union {
struct {
uint32_t fifo_wdata: 9; /*This is the data need to be pushed into out link descriptor's fifo.*/
uint32_t reserved9: 7;
uint32_t fifo_push: 1; /*Set this bit to push data in out link descriptor's fifo.*/
uint32_t reserved17:15;
};
uint32_t val;
} dma_out_push;
union {
struct {
uint32_t full: 1;
uint32_t empty: 1;
uint32_t reserved2: 2;
uint32_t rx_err_cause: 3; /*This register stores the errors caused in out link descriptor's data packet.*/
uint32_t reserved7: 25;
};
uint32_t val;
} dma_in_status;
union {
struct {
uint32_t fifo_rdata: 12; /*This register stores the data pop from in link descriptor's fifo.*/
uint32_t reserved12: 4;
uint32_t fifo_pop: 1; /*Set this bit to pop data in in link descriptor's fifo.*/
uint32_t reserved17: 15;
};
uint32_t val;
} dma_in_pop;
union {
struct {
uint32_t addr: 20; /*This register stores the least 20 bits of the first out link descriptor's address.*/
uint32_t reserved20: 8;
uint32_t stop: 1; /*Set this bit to stop dealing with the out link descriptors.*/
uint32_t start: 1; /*Set this bit to start dealing with the out link descriptors.*/
uint32_t restart: 1; /*Set this bit to mount on new out link descriptors*/
uint32_t park: 1; /*1 the out link descriptor's fsm is in idle state. 0:the out link descriptor's fsm is working.*/
};
uint32_t val;
} dma_out_link;
union {
struct {
uint32_t addr: 20; /*This register stores the least 20 bits of the first in link descriptor's address.*/
uint32_t auto_ret: 1; /*1:when a packet is wrong in link descriptor returns to the descriptor which is lately used.*/
uint32_t reserved21: 7;
uint32_t stop: 1; /*Set this bit to stop dealing with the in link descriptors.*/
uint32_t start: 1; /*Set this bit to start dealing with the in link descriptors.*/
uint32_t restart: 1; /*Set this bit to mount on new in link descriptors*/
uint32_t park: 1; /*1:the in link descriptor's fsm is in idle state. 0:the in link descriptor's fsm is working*/
};
uint32_t val;
} dma_in_link;
union {
struct {
uint32_t check_sum_en: 1; /*Set this bit to enable decoder to check check_sum in packet header.*/
uint32_t check_seq_en: 1; /*Set this bit to enable decoder to check seq num in packet header.*/
uint32_t crc_disable: 1; /*Set this bit to disable crc calculation.*/
uint32_t save_head: 1; /*Set this bit to save packet header .*/
uint32_t tx_check_sum_re: 1; /*Set this bit to enable hardware replace check_sum in packet header automatically.*/
uint32_t tx_ack_num_re: 1; /*Set this bit to enable hardware replace ack num in packet header automatically.*/
uint32_t check_owner: 1; /*Set this bit to check the owner bit in link descriptor.*/
uint32_t wait_sw_start: 1; /*Set this bit to enable software way to add packet header.*/
uint32_t sw_start: 1; /*Set this bit to start inserting the packet header.*/
uint32_t dma_in_fifo_full_thrs:12; /*when data amount in link descriptor's fifo is more than this register value it will produce uhci_dma_in_fifo_full_wm_int interrupt.*/
uint32_t reserved21: 11;
};
uint32_t val;
} conf1;
uint32_t state0; /**/
uint32_t state1; /**/
uint32_t dma_out_eof_des_addr; /*This register stores the address of out link description when eof bit in this descriptor is 1.*/
uint32_t dma_in_suc_eof_des_addr; /*This register stores the address of in link descriptor when eof bit in this descriptor is 1.*/
uint32_t dma_in_err_eof_des_addr; /*This register stores the address of in link descriptor when there are some errors in this descriptor.*/
uint32_t dma_out_eof_bfr_des_addr; /*This register stores the address of out link descriptor when there are some errors in this descriptor.*/
union {
struct {
uint32_t test_mode: 3; /*bit2 is ahb bus test enable bit1 is used to choose write(1) or read(0) mode. bit0 is used to choose test only once(1) or continue(0)*/
uint32_t reserved3: 1;
uint32_t test_addr: 2; /*The two bits represent ahb bus address bit[20:19]*/
uint32_t reserved6: 26;
};
uint32_t val;
} ahb_test;
uint32_t dma_in_dscr; /*The content of current in link descriptor's third dword*/
uint32_t dma_in_dscr_bf0; /*The content of current in link descriptor's first dword*/
uint32_t dma_in_dscr_bf1; /*The content of current in link descriptor's second dword*/
uint32_t dma_out_dscr; /*The content of current out link descriptor's third dword*/
uint32_t dma_out_dscr_bf0; /*The content of current out link descriptor's first dword*/
uint32_t dma_out_dscr_bf1; /*The content of current out link descriptor's second dword*/
union {
struct {
uint32_t tx_c0_esc_en: 1; /*Set this bit to enable 0xc0 char decode when DMA receives data.*/
uint32_t tx_db_esc_en: 1; /*Set this bit to enable 0xdb char decode when DMA receives data.*/
uint32_t tx_11_esc_en: 1; /*Set this bit to enable flow control char 0x11 decode when DMA receives data.*/
uint32_t tx_13_esc_en: 1; /*Set this bit to enable flow control char 0x13 decode when DMA receives data.*/
uint32_t rx_c0_esc_en: 1; /*Set this bit to enable 0xc0 char replace when DMA sends data.*/
uint32_t rx_db_esc_en: 1; /*Set this bit to enable 0xdb char replace when DMA sends data.*/
uint32_t rx_11_esc_en: 1; /*Set this bit to enable flow control char 0x11 replace when DMA sends data.*/
uint32_t rx_13_esc_en: 1; /*Set this bit to enable flow control char 0x13 replace when DMA sends data.*/
uint32_t reserved8: 24;
};
uint32_t val;
} escape_conf;
union {
struct {
uint32_t txfifo_timeout: 8; /*This register stores the timeout value.when DMA takes more time than this register value to receive a data it will produce uhci_tx_hung_int interrupt.*/
uint32_t txfifo_timeout_shift: 3; /*The tick count is cleared when its value >=(17'd8000>>reg_txfifo_timeout_shift)*/
uint32_t txfifo_timeout_ena: 1; /*The enable bit for tx fifo receive data timeout*/
uint32_t rxfifo_timeout: 8; /*This register stores the timeout value.when DMA takes more time than this register value to read a data from RAM it will produce uhci_rx_hung_int interrupt.*/
uint32_t rxfifo_timeout_shift: 3; /*The tick count is cleared when its value >=(17'd8000>>reg_rxfifo_timeout_shift)*/
uint32_t rxfifo_timeout_ena: 1; /*This is the enable bit for DMA send data timeout*/
uint32_t reserved24: 8;
};
uint32_t val;
} hung_conf;
uint32_t ack_num; /**/
uint32_t rx_head; /*This register stores the packet header received by DMA*/
union {
struct {
uint32_t single_send_num: 3; /*The bits are used to choose which short packet*/
uint32_t single_send_en: 1; /*Set this bit to enable send a short packet*/
uint32_t always_send_num: 3; /*The bits are used to choose which short packet*/
uint32_t always_send_en: 1; /*Set this bit to enable continuously send the same short packet*/
uint32_t reserved8: 24;
};
uint32_t val;
} quick_sent;
struct{
uint32_t w_data[2]; /*This register stores the content of short packet's dword*/
} q_data[7];
union {
struct {
uint32_t seper_char: 8; /*This register stores the separator char separator char is used to separate the data frame.*/
uint32_t seper_esc_char0: 8; /*This register stores the first char used to replace separator char in data.*/
uint32_t seper_esc_char1: 8; /*This register stores the second char used to replace separator char in data . 0xdc 0xdb replace 0xc0 by default.*/
uint32_t reserved24: 8;
};
uint32_t val;
} esc_conf0;
union {
struct {
uint32_t seq0: 8; /*This register stores the first substitute char used to replace the separate char.*/
uint32_t seq0_char0: 8; /*This register stores the first char used to replace reg_esc_seq0 in data.*/
uint32_t seq0_char1: 8; /*This register stores the second char used to replace the reg_esc_seq0 in data*/
uint32_t reserved24: 8;
};
uint32_t val;
} esc_conf1;
union {
struct {
uint32_t seq1: 8; /*This register stores the flow control char to turn on the flow_control*/
uint32_t seq1_char0: 8; /*This register stores the first char used to replace the reg_esc_seq1 in data.*/
uint32_t seq1_char1: 8; /*This register stores the second char used to replace the reg_esc_seq1 in data.*/
uint32_t reserved24: 8;
};
uint32_t val;
} esc_conf2;
union {
struct {
uint32_t seq2: 8; /*This register stores the flow_control char to turn off the flow_control*/
uint32_t seq2_char0: 8; /*This register stores the first char used to replace the reg_esc_seq2 in data.*/
uint32_t seq2_char1: 8; /*This register stores the second char used to replace the reg_esc_seq2 in data.*/
uint32_t reserved24: 8;
};
uint32_t val;
} esc_conf3;
union {
struct {
uint32_t thrs: 13; /*when the amount of packet payload is larger than this value the process of receiving data is done.*/
uint32_t reserved13:19;
};
uint32_t val;
} pkt_thres;
uint32_t reserved_c4;
uint32_t reserved_c8;
uint32_t reserved_cc;
uint32_t reserved_d0;
uint32_t reserved_d4;
uint32_t reserved_d8;
uint32_t reserved_dc;
uint32_t reserved_e0;
uint32_t reserved_e4;
uint32_t reserved_e8;
uint32_t reserved_ec;
uint32_t reserved_f0;
uint32_t reserved_f4;
uint32_t reserved_f8;
uint32_t date; /*version information*/
} uhci_dev_t;
extern uhci_dev_t UHCI0;
extern uhci_dev_t UHCI1;
#endif /* _SOC_UHCI_STRUCT_H_ */