![]() This commit updates the README files for the ULP RISC-V I2C and Touch sensor examples to mention the GPIO configuration needed to run the examples. |
||
---|---|---|
.. | ||
main | ||
CMakeLists.txt | ||
README.md | ||
sdkconfig.defaults |
README.md
Supported Targets | ESP32-S2 | ESP32-S3 |
---|
ULP RISC-V I2C Example
This example demonstrates how to use the RTC I2C peripheral from the ULP RISC-V coprocessor in deep sleep.
The ULP program is based on the BMP180 Temperature and Pressure sensor (https://cz.mouser.com/datasheet/2/783/BST-BMP180-DS000-1509579.pdf) which has an I2C interface. The main CPU initializes the RTC I2C peripheral, the BMP180 sensor and loads the ULP program. It then goes into deep sleep.
The ULP program periodically measures the temperature and pressure values from the BMP180 sensor and wakes up the main CPU when the values are above a certain threshold.
How to use example
Hardware Required
- A development board with a SOC which has a RISC-V ULP coprocessor (e.g., ESP32-S2 Saola)
- A BMP180 sensor module
- A USB cable for power supply and programming
Pin Assignment:
Note: The following pin assignments are used by default.
SDA | SCL | |
---|---|---|
ESP32-S2/S3 RTC I2C Master | GPIO3 | GPIO2 |
BMP180 Sensor | SDA | SCL |
Note: The SDA line can only be configured to use either GPIO1 or GPIO3 and the SCL line can only be configured to use either GPIO0 or GPIO2. Note: This example enables the internal pull-up resistors for the SDA/SCL lines by default.
Example output
Below is the output from this example.
Not a ULP-RISC V wakeup (cause = 0)
Initializing RTC I2C ...
RTC_I2C_STATUS_REG = 0x00000000
Reading calibration data from BMP180 ...
ac1 = 7819
ac2 = -1152
ac3 = -14317
ac4 = 34252
ac5 = 25122
ac6 = 14289
b1 = 6515
b2 = 44
mb = -32768
mc = -11786
md = 2746
Reading initial uncompensated temperature and pressure data ...
Uncompensated Temperature = 22865
Uncompensated Pressure = 41768
Real Temperature = 24.900000 deg celcius
Real Pressure = 990.640000 hPa
Entering in deep sleep
ESP-ROM:esp32s2-rc4-20191025
Build:Oct 25 2019
rst:0x5 (DSLEEP),boot:0x9 (SPI_FAST_FLASH_BOOT)
SPIWP:0xee
mode:DIO, clock div:1
load:0x3ffe6108,len:0x1298
load:0x4004c000,len:0x92c
load:0x40050000,len:0x2f04
entry 0x4004c154
W (76) spi_flash: Detected size(4096k) larger than the size in the binary image header(2048k). Using the size in the binary image header.
ULP RISC-V woke up the main CPU
Uncompensated Temperature = 22865
Uncompensated Pressure = 41765
Reading calibration data from BMP180 ...
ac1 = 7819
ac2 = -1152
ac3 = -14317
ac4 = 34252
ac5 = 25122
ac6 = 14289
b1 = 6515
b2 = 44
mb = -32768
mc = -11786
md = 2746
New Real Temperature = 24.900000 deg celcius
New Real Pressure = 990.550000 hPa
Entering in deep sleep