menu "PHY"

    config ESP32_PHY_CALIBRATION_AND_DATA_STORAGE
        bool "Store phy calibration data in NVS"
        default y
        help
            If this option is enabled, NVS will be initialized and calibration data will be loaded from there.
            PHY calibration will be skipped on deep sleep wakeup. If calibration data is not found, full calibration
            will be performed and stored in NVS. Normally, only partial calibration will be performed.
            If this option is disabled, full calibration will be performed.

            If it's easy that your board calibrate bad data, choose 'n'.
            Two cases for example, you should choose 'n':
            1.If your board is easy to be booted up with antenna disconnected.
            2.Because of your board design, each time when you do calibration, the result are too unstable.
            If unsure, choose 'y'.

    menuconfig ESP32_PHY_INIT_DATA_IN_PARTITION
        bool "Use a partition to store PHY init data"
        default n
        help
            If enabled, PHY init data will be loaded from a partition.
            When using a custom partition table, make sure that PHY data
            partition is included (type: 'data', subtype: 'phy').
            With default partition tables, this is done automatically.
            If PHY init data is stored in a partition, it has to be flashed there,
            otherwise runtime error will occur.

            If this option is not enabled, PHY init data will be embedded
            into the application binary.

            If unsure, choose 'n'.

    config ESP32_PHY_DEFAULT_INIT_IF_INVALID
        bool "Reset default PHY init data if invalid"
        default n
        depends on ESP32_PHY_INIT_DATA_IN_PARTITION
        help
            If enabled, PHY init data will be restored to default if
            it cannot be verified successfully to avoid endless bootloops.

            If unsure, choose 'n'.

    if ESP32_PHY_INIT_DATA_IN_PARTITION
        config ESP32_SUPPORT_MULTIPLE_PHY_INIT_DATA_BIN
            bool "Support multiple PHY init data bin"
            depends on ESP32_PHY_INIT_DATA_IN_PARTITION
            default n
            help
                If enabled, the corresponding PHY init data type can be automatically switched
                according to the country code. China's PHY init data bin is used by default.
                Can be modified by country information in API esp_wifi_set_country().
                The priority of switching the PHY init data type is:
                1. Country configured by API esp_wifi_set_country()
                and the parameter policy is WIFI_COUNTRY_POLICY_MANUAL.
                2. Country notified by the connected AP.
                3. Country configured by API esp_wifi_set_country()
                and the parameter policy is WIFI_COUNTRY_POLICY_AUTO.

        config ESP32_PHY_INIT_DATA_ERROR
            bool "Terminate operation when PHY init data error"
            depends on ESP32_SUPPORT_MULTIPLE_PHY_INIT_DATA_BIN
            default n
            help
                If enabled, when an error occurs while the PHY init data is updated,
                the program will terminate and restart.
                If not enabled, the PHY init data will not be updated when an error occurs.
    endif

    config ESP32_PHY_MAX_WIFI_TX_POWER
        int "Max WiFi TX power (dBm)"
        range 10 20
        default 20
        help
            Set maximum transmit power for WiFi radio. Actual transmit power for high
            data rates may be lower than this setting.

    config ESP32_PHY_MAX_TX_POWER
        int
        default ESP32_PHY_MAX_WIFI_TX_POWER

    config ESP32_PHY_MAC_BB_PD
        bool "Power down MAC and baseband of Wi-Fi and Bluetooth when PHY is disabled"
        depends on (IDF_TARGET_ESP32C3 && FREERTOS_USE_TICKLESS_IDLE)
        default n
        help
            If enabled, the MAC and baseband of Wi-Fi and Bluetooth will be powered
            down when PHY is disabled. Enabling this setting reduces power consumption
            by a small amount but increases RAM use by approximately 4 KB(Wi-Fi only),
            2 KB(Bluetooth only) or 5.3 KB(Wi-Fi + Bluetooth).

    config ESP32_REDUCE_PHY_TX_POWER
        bool "Reduce PHY TX power when brownout reset"
        depends on ESP32_BROWNOUT_DET
        default y
        help
            When brownout reset occurs, reduce PHY TX power to keep the code running.

endmenu  # PHY