// Copyright 2021 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//     http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.

#pragma once

#ifdef __cplusplus
extern "C" {
#endif

#include "esp_eth_phy.h"
#include "esp_eth_mac.h"
#include "driver/spi_master.h"

#define CS_HOLD_TIME_MIN_NS 210

/**
 * @brief ENC28J60 specific configuration
 *
 */
typedef struct {
    spi_device_handle_t spi_hdl; /*!< Handle of SPI device driver */
    int int_gpio_num;            /*!< Interrupt GPIO number */
} eth_enc28j60_config_t;

/**
 * @brief ENC28J60 Supported Revisions
 *
 */
typedef enum {
    ENC28J60_REV_B1 = 0b00000010,
    ENC28J60_REV_B4 = 0b00000100,
    ENC28J60_REV_B5 = 0b00000101,
    ENC28J60_REV_B7 = 0b00000110
} eth_enc28j60_rev_t;

/**
 * @brief Default ENC28J60 specific configuration
 *
 */
#define ETH_ENC28J60_DEFAULT_CONFIG(spi_device) \
    {                                           \
        .spi_hdl = spi_device,                  \
        .int_gpio_num = 4,                      \
    }

/**
 * @brief Compute amount of SPI bit-cycles the CS should stay active after the transmission
 *        to meet ENC28J60 CS Hold Time specification.
 *
 * @param clock_speed_mhz SPI Clock frequency in MHz (valid range is <1, 20>)
 * @return uint8_t
 */
static inline uint8_t enc28j60_cal_spi_cs_hold_time(int clock_speed_mhz)
{
    if (clock_speed_mhz <= 0 || clock_speed_mhz > 20) {
        return 0;
    }
    int temp = clock_speed_mhz * CS_HOLD_TIME_MIN_NS;
    uint8_t cs_posttrans = temp / 1000;
    if (temp % 1000) {
        cs_posttrans += 1;
    }

    return cs_posttrans;
}

/**
* @brief Create ENC28J60 Ethernet MAC instance
*
* @param[in] enc28j60_config: ENC28J60 specific configuration
* @param[in] mac_config: Ethernet MAC configuration
*
* @return
*      - instance: create MAC instance successfully
*      - NULL: create MAC instance failed because some error occurred
*/
esp_eth_mac_t *esp_eth_mac_new_enc28j60(const eth_enc28j60_config_t *enc28j60_config, const eth_mac_config_t *mac_config);

/**
* @brief Create a PHY instance of ENC28J60
*
* @param[in] config: configuration of PHY
*
* @return
*      - instance: create PHY instance successfully
*      - NULL: create PHY instance failed because some error occurred
*/
esp_eth_phy_t *esp_eth_phy_new_enc28j60(const eth_phy_config_t *config);

// todo: the below functions should be accessed through ioctl in the future
/**
 * @brief Set ENC28J60 Duplex mode. It sets Duplex mode first to the PHY and then
 *        MAC is set based on what PHY indicates.
 *
 * @param phy ENC28J60 PHY Handle
 * @param duplex Duplex mode
 *
 * @return esp_err_t
 *          - ESP_OK when PHY registers were correctly written.
 */
esp_err_t enc28j60_set_phy_duplex(esp_eth_phy_t *phy, eth_duplex_t duplex);

/**
 * @brief Get ENC28J60 silicon revision ID
 *
 * @param mac ENC28J60 MAC Handle
 * @return eth_enc28j60_rev_t
 *           - returns silicon revision ID read during initialization
 */
eth_enc28j60_rev_t emac_enc28j60_get_chip_info(esp_eth_mac_t *mac);

#ifdef __cplusplus
}
#endif