| Supported Targets | ESP32 | ESP32-C3 | ESP32-C6 | ESP32-H2 | ESP32-S2 | ESP32-S3 | | ----------------- | ----- | -------- | -------- | -------- | -------- | -------- | # TWAI Network Example (See the README.md file in the upper level 'examples' directory for more information about examples.) This example demonstrates how to use the TWAI driver to program a target (ESP32, ESP32-S2, ESP32-S3 or ESP32-C3) as a TWAI node, and have the two nodes (Network Master and Network Slave) communicate on a TWAI network. The Listen Only node is optional and acts as a network monitor meaning that it only receives messages and does not influence the bus in any way (i.e. doesn't not acknowledge or send error frames). Note that concept of master/slave in this example refers to which node initiates and stops the transfer of a stream of data messages. ## How to use example ### Hardware Required This example requires at least two targets (e.g., an ESP32 or ESP32-S2) to act as the Network Master and Network Slave. The third target (Listen Only) is optional. Each target must be connected to an external transceiver (e.g., a SN65HVD23X transceiver). The transceivers must then be interconnected to form a TWAI network. The following diagram illustrates an example network: ```text ---------- ---------- -------------- | Master | | Slave | | Listen Only | | | | | | | | TX RX | | TX RX | | TX RX | ---------- ---------- -------------- | | | | | | | | | | | | ---------- ---------- ---------- | D R | | D R | | D R | | | | | | | | VP230 | | VP230 | | VP230 | | | | | | | | H L | | H L | | H L | ---------- ---------- ---------- | | | | | | | | | | | | |--x------|-----x------|-----x------|--| H | | | |---------x------------x------------x--| L ``` Note: If you don't have an external transceiver, you can still run the [TWAI Self Test example](../twai_self_test/README.md) ### Configure the project For each node in the TWAI network (i.e., Master, Slave, Listen Only)... * Set the target of the build (where `{IDF_TARGET}` stands for the target chip such as `esp32` or `esp32s2`). * Then run `menuconfig` to configure the example. ```sh idf.py set-target {IDF_TARGET} idf.py menuconfig ``` * Under `Example Configuration`, configure the pin assignments using the options `TX GPIO Number` and `RX GPIO Number` according to how the target was connected to the transceiver. By default, `TX GPIO Number` and `RX GPIO Number` are set to the following values: * On the ESP32, `TX GPIO Number` and `RX GPIO Number` default to `21` and `22` respectively * On other chips, `TX GPIO Number` and `RX GPIO Number` default to `0` and `2` respectively ### Build and Flash For each node, build the project and flash it to the board, then run monitor tool to view serial output: ```sh idf.py -p PORT flash monitor ``` (Replace PORT with the name of the serial port to use.) (To exit the serial monitor, type ``Ctrl-]``.) See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects. ## Example Output Network Master ```text I (345) TWAI Master: Driver installed I (345) TWAI Master: Driver started I (345) TWAI Master: Transmitting ping I (3105) TWAI Master: Transmitted start command I (3105) TWAI Master: Received data value 339 ... I (5545) TWAI Master: Received data value 584 I (5545) TWAI Master: Transmitted stop command I (5595) TWAI Master: Driver stopped I (6595) TWAI Master: Driver started I (6595) TWAI Master: Transmitting ping I (7095) TWAI Master: Transmitted start command I (7095) TWAI Master: Received data value 738 ... I (9535) TWAI Master: Received data value 983 I (9535) TWAI Master: Transmitted stop command I (9585) TWAI Master: Driver stopped I (10585) TWAI Master: Driver started I (10585) TWAI Master: Transmitting ping I (11085) TWAI Master: Transmitted start command I (11085) TWAI Master: Received data value 1137 ... I (13525) TWAI Master: Received data value 1382 I (13525) TWAI Master: Transmitted stop command I (13575) TWAI Master: Driver stopped I (14575) TWAI Master: Driver uninstalled ``` Network Slave ```text Slave starting in 3 Slave starting in 2 Slave starting in 1 I (6322) TWAI Slave: Driver installed I (6322) TWAI Slave: Driver started I (6462) TWAI Slave: Transmitted ping response I (6712) TWAI Slave: Start transmitting data I (6712) TWAI Slave: Transmitted data value 339 ... I (9162) TWAI Slave: Transmitted data value 584 I (9212) TWAI Slave: Transmitted stop response I (9312) TWAI Slave: Driver stopped I (10312) TWAI Slave: Driver started I (10452) TWAI Slave: Transmitted ping response I (10702) TWAI Slave: Start transmitting data I (10702) TWAI Slave: Transmitted data value 738 ... I (13152) TWAI Slave: Transmitted data value 983 I (13202) TWAI Slave: Transmitted stop response I (13302) TWAI Slave: Driver stopped I (14302) TWAI Slave: Driver started I (14442) TWAI Slave: Transmitted ping response I (14692) TWAI Slave: Start transmitting data I (14692) TWAI Slave: Transmitted data value 1137 ... I (17142) TWAI Slave: Transmitted data value 1382 I (17192) TWAI Slave: Transmitted stop response I (17292) TWAI Slave: Driver stopped I (18292) TWAI Slave: Driver uninstalled ``` Network Listen Only ```text I (326) TWAI Listen Only: Driver installed I (326) TWAI Listen Only: Driver started I (366) TWAI Listen Only: Received master ping ... I (1866) TWAI Listen Only: Received master ping I (1866) TWAI Listen Only: Received slave ping response I (2116) TWAI Listen Only: Received master start command I (2116) TWAI Listen Only: Received data value 329 ... I (4566) TWAI Listen Only: Received data value 574 I (4566) TWAI Listen Only: Received master stop command I (4606) TWAI Listen Only: Received slave stop response I (5606) TWAI Listen Only: Received master ping I (5856) TWAI Listen Only: Received master ping I (5856) TWAI Listen Only: Received slave ping response I (6106) TWAI Listen Only: Received master start command I (6106) TWAI Listen Only: Received data value 728 ... I (8556) TWAI Listen Only: Received data value 973 I (8556) TWAI Listen Only: Received master stop command I (8596) TWAI Listen Only: Received slave stop response I (9596) TWAI Listen Only: Received master ping I (9846) TWAI Listen Only: Received master ping I (9846) TWAI Listen Only: Received slave ping response I (10096) TWAI Listen Only: Received master start command I (10096) TWAI Listen Only: Received data value 1127 ... I (12546) TWAI Listen Only: Received data value 1372 I (12546) TWAI Listen Only: Received master stop command I (12586) TWAI Listen Only: Received slave stop response I (12586) TWAI Listen Only: Driver stopped I (12586) TWAI Listen Only: Driver uninstalled ``` ## Example Breakdown The communication between the Network Master and Network Slave execute the following steps over multiple iterations: 1. Both master and slave go through install and start their TWAI drivers independently. 2. The master repeatedly sends **PING** messages until it receives a **PING_RESP** (ping response message) from the slave. The slave will only send a **PING_RESP** message when it receives a **PING** message from the master. 3. Once the master has received the **PING_RESP** from the slave, it will send a **START_CMD** message to the slave. 4. Upon receiving the **START_CMD** message, the slave will start transmitting **DATA** messages until the master sends a **STOP_CMD**. The master will send the **STOP_CMD** after receiving N **DATA** messages from the slave (N = 50 by default). 5. When the slave receives the **STOP_CMD**, it will confirm that it has stopped by sending a **STOP_RESP** message to the master.