* Modify the function implementation of ESP32-S2 RTC GPIO
On ESP32 those PADs which have RTC functions must set pullup/down/capability via RTC register.
On ESP32-S2, Digital IOs have their own registers to control pullup/down/capability, independent with RTC registers.
* Add ESP32-S2 support of unit test
* Modify the pull-up test of unit test
* Modify the interrupt test of unit test
* Modify input and output mode test of unit test
Using xxx_periph.h in whole IDF instead of xxx_reg.h, xxx_struct.h, xxx_channel.h ... .
Cleaned up header files from unnecessary headers (releated to soc/... headers).
Removed as much branching (if statements) from the
gpio_intr_service ISR, as possible and split the while loop into
two. Also forced writing the two status*_w1tc variables only once,
instead of every time after calling the external function hooks.
The measurements below, was done using the following tools:
Toolchain version: crosstool-ng-1.22.0-80-g6c4433a
Compiler version: 5.2.0
Here follows a comparison of the gpio_intr_service ISR's
execution time, using a DS1054 oscilloscope. All the time spent
calling external functions, via the function pointers
gpio_isr_func[gpio_num].fn, were disregarded.
With OPTIMIZATION_FLAGS = -Og, 1.34 uSeconds faster:
3.22 uSec (with this patch)
4.56 uSec (with commit 71c90ac4)
100 - (100 * 4.56 / 3.22) = 42% faster
With OPTIMIZATION_FLAGS = -Os, 1.65 uSeconds faster:
2.89 uSec (with this patch)
4.54 uSec (with commit 71c90ac4)
100 - (100 * 4.54 / 2.89) = 57% faster
Signed-off-by: Konstantin Kondrashov <konstantin@espressif.com>
Merges https://github.com/espressif/esp-idf/pull/2861
For pins 32 and up the BIT(nr) macro used here overflowed,
causing undetermined GPIO pins to be reset.
Example: freeing SPI device/bus where CS is on pin 33
caused debug UART to cease communication, TXD0 was
disabled.
Fixed as BIT64(nr) macro, to be used elsewhere as needed.
For example in definitions like GPIO_SEL_32..GPIO_SEL_39.
The TRM describes IOMUX registers are IO_MUX_x_REG for x in GPIO0-39.
Until now ESP-IDF describes them as PERIPHS_IO_MUX_(pinname)_U
This commit adds additional IOMUX register names which match the ones used in the TRM.
1. add ISR handler apis so that users of different layers can hook their own isr handler on different GPIO.
Audio project has different software layers, they need different gpio isr handler for layer instead of processing all GPIO interrupts in one handler.
If this kind of calling a handler from isr is not proper, please kindly point out.
2. add gpio example code.
3. improve gpio.rst
4. add readme for gpio example
Squashed commits:
[278e50f] update: GPIO
1. coding style, add a space between conditional or loop keyword and an opening paren.
2. modify some return value and doc
3. use printf in example code
Squashed commits:
[efb23bb] minor change of comment
1. add sigma-delta code and example.
2. add gpio output signal in io matrix.
Squashed commits:
[a25e7d4] minor changes for doc
[6a03a1e] minor changes on comments and doc.
[97dd9e4] Add doc.
update index.rst
change example index
This adds the following APIs to enable various wakeup sources:
- esp_deep_sleep_enable_timer_wakeup
- esp_deep_sleep_enable_ulp_wakeup
- esp_deep_sleep_enable_ext0_wakeup
- esp_deep_sleep_enable_ext1_wakeup
And an API to start deep sleep:
- esp_deep_sleep_start
drivers: remove file paths from log statements
Function name and error string are usually sufficient to find the place which has triggered an error.
`__FILE__` macro generates a string which has absolute file name (with our build system), which add many long strings to the program binary.
Also change log tags to lower case to match style used elsewhere.
Fixes https://github.com/espressif/esp-idf/issues/126
See merge request !282
feature(rtc_module):add rtc module
1. add rtc io control API (pull,output and input)
2. add touch pad API (touch pad read and interrupt)
3. add adc1 API (the max width is 12 Bits and support attenuation)
4. add hall sensor API (support hall sensor read )
5. add dac API (the width is 8 Bits)
bugfix(gpio):gpio32 and gpio33 can not output and input
the gpio32 and gpio33 is initialize by librtc.a,and gpio_config not initialize the gpio as
digital gpio.they can not output and input,when users use gpio32 or gpio33.And there are some problems
about others driver ,when they use gpio32 or gpio33 as matrix.
Function name and error string are usually sufficient to find the place which has triggered an error. __FILE__ macro generates a string which has absolute file name (with our build system), so there is a lot of long strings present in the program because of that.
Fixes https://github.com/espressif/esp-idf/issues/126
1. remove "\n" when calling ESP_LOGX APIs.
2. modify uart_event_t for uart rx data.
3. use MICRO for uart inverse value
4. add uart_tx_data_t for internal tx function.
1. Set XXX_TAG static, remove extern XXX_TAG in uart.h/ledc.h/gpio.h
2. I removed uart_set/get_print_port() functions, these functions are not well tested, I removed them for now.
3. Modify some function names for uart_read/write_bytes
4. Modify uart_write_bytes and uart_write_bytes_with_break.
1. Use esp_log API for LEDC and GPIO code.
2. Modify some API return value.
3. Add ledc_set_pin() for LEDC
4. Modify typo in uart.h
Questions: In uart driver ISR handler, I used xxxFromISR , like xSemaphoreGiveFromISR, do those FromISR functions need to be put in IRAM?
morris