Problem Decribe
The problem happenned when do wps with a mikrotik router
1. router always want to do connect with 32 without EAP-WSC step
2. after 4 way timeour, 32 crash
Root Cause
The reason why can not start EAP-WSC step is router's check method is RSN > WPA > WPS, when it found there include RSN and WPS in assoc, it will choice do 4 way rather than WPS
The reason of second problem is 32's EAPOL start timer didn't stop and send EAPOL start to a null pointer
Soultion
1. remove RSN and WPA ie when do WPS step
2. check mac address's pointer before send EAPOL start
closes: https://github.com/espressif/esp-idf/issues/2382
Fix following WiFi bugs:
1. Fix the bug that MIC verification fails on soft-AP mode
2. Modify mesh root to have same behavior as normal WiFi STA in state change
3. Fix the bug that sniffer can't catch control packets
4. Fix crash bug in soft-AP mode
5. Fix ACM(Admission Control Management) bug
Routine `spi_flash_cache2phys` sometimes return incorrect value,
resulting in failure in getting currently running ota partition.
This in turn aborts firmware update process.This issue was more
prominent with SPIRAM enabled cases.
Fix ensures proper cache guards during `spi_flash_cache2phys`, and
also for few other similar APIs.
In addition, `esp_ota_get_running_partition` has also been optimized
to save currently running partition for subsequent invocations.
Fixes https://github.com/espressif/esp-idf/issues/2451
In earlier change this component was decoupled from freertos and hence
regression was introduced which changed default placement to flash. Some
device drivers make use of ringbuffer while flash cache is being disabled
and hence default placement should instead be internal memory.
Closes: https://github.com/espressif/esp-idf/issues/2517
1. fix some bugs by previous coex hw blocking bugfix,
such like, rwble.c (64, 0) line 222
2. fix bug that ble scan performance is very low when software coexist
is working.
3. update libcoexist version to v1.1.0
In some cases, when data was just written into UART FIFO, transmitter
state could be still zero while the FIFO did contain some data.
This resulted in uart_tx_wait_idle occasionally returning before all
the data was sent out.
Fix by checking both UART transmitter state and TX FIFO count.
1. Fix the bug that ESP32 will reject the retry AddBA request frame
if AddBA response frame is failed to sent by WiFi LMAC
2. Fix the bug that AddBA request retrys too frequently
3. Forbid BA session setup for VO queue related TID
1. remove use EID to distinguish psram voltage
2. 1V8 64Mbit psram and 3V3 64Mbit psram use the same psram driver(standard spi interface)
3. set cs hold time register as 1
In some cases, linker could choose to use ROM functions instead of the
ones defined in IDF.
For functions used in ROM stub table, this would lead to infinite
recursion when the corresponding function was called from ROM.
For crypto functions, some of these were modified in IDF, and
incompatible with ROM counterparts.
Problem Description
The reporduce steps are as follows:
1. put more than one same ssid AP in the environment;
2. set the STA mac address in one of the APs blacklist, and make sure the AP is closest to STA;
3. set the scan method in station config as all channel scan;
4. try to connect the AP which set STA in blacklist
Phenmenon
STA fail to connect after send auth or assoc with a wrong status code, but no disconnect event report and can not connect the next one in the envrionment
Root Cause
Because there are some same ssid APs in the evnrionment, when do all channel scan, it will collect all the matched AP in rc list, because rc list is not empty, so it would send disconnect event, however, we didn't do other step such as connect to other one
VNC MR 570
closes https://github.com/espressif/esp-idf/issues/2323
_rtc_data_{start,end} can now describe data placed into RTC_FAST
segment, if CONFIG_ESP32_RTCDATA_IN_FAST_MEM is enabled.
Use new _rtc_slow_length symbol instead.
fix the bug following:
1. after disable bluetooth controller, wifi cannot TX/RX any packets.
2. when software coexist working, there's a little ratio cause wifi task watchdog timeout
3. when software coexist working, there's a little ratio cause bluetooth cannot receive anything.
feature:
1. add libbtdm_app.a git commit local and remote checking
Known issues:
1. there's still a bug occurs with a very very low ratio cause bluetooth
cannot receive anything. The reproduce interval may great than 3days ~ 1week via
7x24 hours heavy testing.
wangmengyang