esp_eth: change rtl8201 reset timing to match datasheet

In esp_eth_phy_rtl8201.c:
Add 150ms delay after hardware reset, chage reset assertion time to 10ms

In esp_eth_phy_802_3.c:
Change reset function to use vTaskDelay for long (>=10ms) reset assertion time
Change esp_eth_phy_802_3_detect_phy_addr to check range 0-31 instead of 0-15.

components/esp_eth/src/esp_eth_phy_802_3.c

@@ -366,7 +366,11 @@ esp_err_t esp_eth_phy_802_3_reset_hw(phy_802_3_t *phy_802_3, uint32_t reset_asse
         esp_rom_gpio_pad_select_gpio(phy_802_3->reset_gpio_num);
         gpio_set_direction(phy_802_3->reset_gpio_num, GPIO_MODE_OUTPUT);
         gpio_set_level(phy_802_3->reset_gpio_num, 0);
-        esp_rom_delay_us(reset_assert_us);
+        if (reset_assert_us < 10000) {
+            esp_rom_delay_us(reset_assert_us);
+        } else {
+            vTaskDelay(pdMS_TO_TICKS(reset_assert_us/1000));
+        }
         gpio_set_level(phy_802_3->reset_gpio_num, 1);
     }
     return ESP_OK;
@@ -380,14 +384,14 @@ esp_err_t esp_eth_phy_802_3_detect_phy_addr(esp_eth_mediator_t *eth, int *detect
     }
     int addr_try = 0;
     uint32_t reg_value = 0;
-    for (; addr_try < 16; addr_try++) {
+    for (; addr_try < 32; addr_try++) {
         eth->phy_reg_read(eth, addr_try, ETH_PHY_IDR1_REG_ADDR, &reg_value);
         if (reg_value != 0xFFFF && reg_value != 0x00) {
             *detected_addr = addr_try;
             break;
         }
     }
-    if (addr_try < 16) {
+    if (addr_try < 32) {
         ESP_LOGD(TAG, "Found PHY address: %d", addr_try);
         return ESP_OK;
     }

components/esp_eth/src/esp_eth_phy_rtl8201.c

@@ -9,8 +9,13 @@
 #include <sys/cdefs.h>
 #include "esp_log.h"
 #include "esp_check.h"
+#include "freertos/FreeRTOS.h"
+#include "freertos/task.h"
 #include "esp_eth_phy_802_3.h"
 
+#define RTL8201_PHY_RESET_ASSERTION_TIME_US 10000
+#define RTL8201_PHY_POST_RESET_INIT_TIME_MS 150
+
 static const char *TAG = "rtl8201";
 
 /***************Vendor Specific Register***************/
@@ -144,6 +149,15 @@ err:
     return ret;
 }
 
+static esp_err_t rtl8201_reset_hw(esp_eth_phy_t *phy)
+{
+    phy_802_3_t *phy_802_3 = esp_eth_phy_into_phy_802_3(phy);
+    esp_err_t ret = esp_eth_phy_802_3_reset_hw(phy_802_3, RTL8201_PHY_RESET_ASSERTION_TIME_US);
+    vTaskDelay(pdMS_TO_TICKS(RTL8201_PHY_POST_RESET_INIT_TIME_MS));
+    return ret;
+}
+
+
 static esp_err_t rtl8201_init(esp_eth_phy_t *phy)
 {
     esp_err_t ret = ESP_OK;
@@ -177,6 +191,7 @@ esp_eth_phy_t *esp_eth_phy_new_rtl8201(const eth_phy_config_t *config)
     rtl8201->phy_802_3.parent.get_link = rtl8201_get_link;
     rtl8201->phy_802_3.parent.autonego_ctrl = rtl8201_autonego_ctrl;
     rtl8201->phy_802_3.parent.loopback = rtl8201_loopback;
+    rtl8201->phy_802_3.parent.reset_hw = rtl8201_reset_hw;
 
     return &rtl8201->phy_802_3.parent;
 err: