feat(brownout): Add brownout detector support on esp32p4

components/esp_system/port/brownout.c

@@ -76,7 +76,9 @@ void esp_brownout_init(void)
 #if CONFIG_IDF_TARGET_ESP32C6 || CONFIG_IDF_TARGET_ESP32H2 || CONFIG_IDF_TARGET_ESP32C5 || CONFIG_IDF_TARGET_ESP32C61  // TODO: [ESP32C5] IDF-8647, [ESP32C61] IDF-9254
     // TODO IDF-6606: LP_RTC_TIMER interrupt source is shared by lp_timer and brownout detector, but lp_timer interrupt
     // is not used now. An interrupt allocator is needed when lp_timer intr gets supported.
-    esp_intr_alloc(ETS_LP_RTC_TIMER_INTR_SOURCE, ESP_INTR_FLAG_IRAM, &rtc_brownout_isr_handler, NULL, NULL);
+    esp_intr_alloc_intrstatus(ETS_LP_RTC_TIMER_INTR_SOURCE, ESP_INTR_FLAG_IRAM | ESP_INTR_FLAG_SHARED, (uint32_t)brownout_ll_intr_get_status_reg(), BROWNOUT_DETECTOR_LL_INTERRUPT_MASK, &rtc_brownout_isr_handler, NULL, NULL);
+#elif CONFIG_IDF_TARGET_ESP32P4
+    esp_intr_alloc(ETS_LP_ANAPERI_INTR_SOURCE, ESP_INTR_FLAG_IRAM, &rtc_brownout_isr_handler, NULL, NULL);
 #else
     rtc_isr_register(rtc_brownout_isr_handler, NULL, RTC_CNTL_BROWN_OUT_INT_ENA_M, RTC_INTR_FLAG_IRAM);
 #endif

components/esp_system/port/soc/esp32p4/Kconfig.system

@@ -0,0 +1,45 @@
+menu "Brownout Detector"
+    config ESP_BROWNOUT_DET
+        bool "Hardware brownout detect & reset"
+        depends on !IDF_ENV_FPGA
+        default y
+        help
+            The ESP32-P4 has a built-in brownout detector which can detect if the voltage is lower than
+            a specific value. If this happens, it will reset the chip in order to prevent unintended
+            behaviour.
+
+    choice ESP_BROWNOUT_DET_LVL_SEL
+        prompt "Brownout voltage level"
+        depends on ESP_BROWNOUT_DET
+        default ESP_BROWNOUT_DET_LVL_SEL_7
+        help
+            The brownout detector will reset the chip when the supply voltage is approximately
+            below this level. Note that there may be some variation of brownout voltage level
+            between each chip.
+
+            #The voltage levels here are estimates, more work needs to be done to figure out the exact voltages
+            #of the brownout threshold levels.
+        config ESP_BROWNOUT_DET_LVL_SEL_7
+            bool "2.51V"
+        config ESP_BROWNOUT_DET_LVL_SEL_6
+            bool "2.64V"
+        config ESP_BROWNOUT_DET_LVL_SEL_5
+            bool "2.76V"
+        config ESP_BROWNOUT_DET_LVL_SEL_4
+            bool "2.92V"
+        config ESP_BROWNOUT_DET_LVL_SEL_3
+            bool "3.10V"
+        config ESP_BROWNOUT_DET_LVL_SEL_2
+            bool "3.27V"
+    endchoice
+
+    config ESP_BROWNOUT_DET_LVL
+        int
+        default 2 if ESP_BROWNOUT_DET_LVL_SEL_2
+        default 3 if ESP_BROWNOUT_DET_LVL_SEL_3
+        default 4 if ESP_BROWNOUT_DET_LVL_SEL_4
+        default 5 if ESP_BROWNOUT_DET_LVL_SEL_5
+        default 6 if ESP_BROWNOUT_DET_LVL_SEL_6
+        default 7 if ESP_BROWNOUT_DET_LVL_SEL_7
+
+endmenu

components/hal/esp32c6/include/hal/brownout_ll.h

@@ -20,6 +20,8 @@
 extern "C" {
 #endif
 
+#define BROWNOUT_DETECTOR_LL_INTERRUPT_MASK   (BIT(31))
+
 /**
  * @brief power down the flash when a brown out happens.
  *
@@ -123,6 +125,16 @@ static inline void brownout_ll_clear_count(void)
     LP_ANA_PERI.bod_mode0_cntl.bod_mode0_cnt_clr = 0;
 }
 
+/**
+ * @brief Get interrupt status register address
+ *
+ * @return Register address
+ */
+static inline volatile void *brownout_ll_intr_get_status_reg(void)
+{
+    return &LP_ANA_PERI.int_st;
+}
+
 #ifdef __cplusplus
 }
 #endif

components/hal/esp32h2/include/hal/brownout_ll.h

@@ -1,5 +1,5 @@
 /*
- * SPDX-FileCopyrightText: 2023 Espressif Systems (Shanghai) CO LTD
+ * SPDX-FileCopyrightText: 2023-2024 Espressif Systems (Shanghai) CO LTD
  *
  * SPDX-License-Identifier: Apache-2.0
  */
@@ -20,6 +20,8 @@
 extern "C" {
 #endif
 
+#define BROWNOUT_DETECTOR_LL_INTERRUPT_MASK   (BIT(31))
+
 /**
  * @brief power down the flash when a brown out happens.
  *
@@ -124,6 +126,16 @@ static inline void brownout_ll_clear_count(void)
     LP_ANA_PERI.bod_mode0_cntl.bod_mode0_cnt_clr = 0;
 }
 
+/**
+ * @brief Get interrupt status register address
+ *
+ * @return Register address
+ */
+static inline volatile void *brownout_ll_intr_get_status_reg(void)
+{
+    return &LP_ANA_PERI.int_st;
+}
+
 #ifdef __cplusplus
 }
 #endif

components/hal/esp32p4/include/hal/brownout_ll.h

@@ -0,0 +1,128 @@
+/*
+ * SPDX-FileCopyrightText: 2023-2024 Espressif Systems (Shanghai) CO LTD
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+/*******************************************************************************
+ * NOTICE
+ * The ll is not public api, don't use in application code.
+ * See readme.md in hal/readme.md
+ ******************************************************************************/
+
+#pragma once
+#include <stdbool.h>
+#include "soc/lp_analog_peri_struct.h"
+#include "hal/regi2c_ctrl.h"
+#include "soc/regi2c_brownout.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * @brief power down the flash when a brown out happens.
+ *
+ * @param enable true: power down flash. false: not power down
+ */
+static inline void brownout_ll_enable_flash_power_down(bool enable)
+{
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_close_flash_ena = enable;
+}
+
+/**
+ * @brief power down the RF circuits when a brown out happens
+ *
+ * @param enable true: power down. false: not power done.
+ */
+static inline void brownout_ll_enable_rf_power_down(bool enable)
+{
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_pd_rf_ena = enable;
+}
+
+/**
+ * @brief Enable this to reset brown out
+ *
+ * @note: If brown out interrupt is used, this should be disabled.
+ *
+ * @param reset_ena true: enable reset. false: disable reset.
+ * @param reset_wait brown out reset wait cycles
+ * @param select 1: chip reset, 0: system reset
+ */
+static inline void brownout_ll_reset_config(bool reset_ena, uint32_t reset_wait, uint8_t select)
+{
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_reset_wait = reset_wait;
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_reset_ena = reset_ena;
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_reset_sel = select;
+}
+/**
+ * @brief Set brown out threshold
+ *
+ * @param threshold brownout threshold
+ */
+static inline void brownout_ll_set_threshold(uint8_t threshold)
+{
+    REGI2C_WRITE_MASK(I2C_BOD, I2C_BOD_THRESHOLD, threshold);
+}
+
+/**
+ * @brief Set this bit to enable the brown out detection
+ *
+ * @param bod_enable true: enable, false: disable
+ */
+static inline void brownout_ll_bod_enable(bool bod_enable)
+{
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_intr_ena = bod_enable;
+}
+
+/**
+ * @brief configure the waiting cycles before sending an interrupt
+ *
+ * @param cycle waiting cycles.
+ */
+static inline void brownout_ll_set_intr_wait_cycles(uint8_t cycle)
+{
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_intr_wait = cycle;
+}
+
+/**
+ * @brief Enable brown out interrupt
+ *
+ * @param enable true: enable, false: disable
+ */
+static inline void brownout_ll_intr_enable(bool enable)
+{
+    LP_ANA_PERI.int_ena.bod_mode0_int_ena = enable;
+}
+
+/**
+ * @brief Enable brownout hardware reset
+ *
+ * @param enable
+ */
+static inline void brownout_ll_ana_reset_enable(bool enable)
+{
+    LP_ANA_PERI.bod_mode1_cntl.bod_mode1_reset_ena = enable;
+}
+
+/**
+ * @brief Clear interrupt bits.
+ */
+__attribute__((always_inline))
+static inline void brownout_ll_intr_clear(void)
+{
+    LP_ANA_PERI.int_clr.bod_mode0_int_clr = 1;
+}
+
+/**
+ * @brief Clear BOD internal count.
+ */
+static inline void brownout_ll_clear_count(void)
+{
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_cnt_clr = 1;
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_cnt_clr = 0;
+}
+
+#ifdef __cplusplus
+}
+#endif

components/soc/esp32p4/include/soc/Kconfig.soc_caps.in

@@ -195,6 +195,10 @@ config SOC_SECURE_BOOT_SUPPORTED
     bool
     default y
 
+config SOC_BOD_SUPPORTED
+    bool
+    default y
+
 config SOC_PMU_SUPPORTED
     bool
     default y

components/soc/esp32p4/include/soc/regi2c_brownout.h

@@ -1,5 +1,5 @@
 /*
- * SPDX-FileCopyrightText: 2022-2023 Espressif Systems (Shanghai) CO LTD
+ * SPDX-FileCopyrightText: 2022-2024 Espressif Systems (Shanghai) CO LTD
  *
  * SPDX-License-Identifier: Apache-2.0
  */
@@ -13,3 +13,10 @@
  * This file lists register fields of the brownout detector, located on an internal configuration
  * bus. These definitions are used via macros defined in regi2c_ctrl.h.
  */
+
+#define I2C_BOD            0x61
+#define I2C_BOD_HOSTID     0
+
+#define I2C_BOD_THRESHOLD           0x5
+#define I2C_BOD_THRESHOLD_MSB       2
+#define I2C_BOD_THRESHOLD_LSB       0

components/soc/esp32p4/include/soc/soc_caps.h

@@ -67,7 +67,7 @@
 #define SOC_KEY_MANAGER_SUPPORTED       1
 #define SOC_FLASH_ENC_SUPPORTED         1
 #define SOC_SECURE_BOOT_SUPPORTED       1
-// #define SOC_BOD_SUPPORTED               1  //TODO: IDF-7519
+#define SOC_BOD_SUPPORTED               1
 // #define SOC_APM_SUPPORTED               1  //TODO: IDF-7542
 #define SOC_PMU_SUPPORTED               1
 #define SOC_DCDC_SUPPORTED              1