mirror
/
esp-idf
kopia lustrzana https://github.com/espressif/esp-idf
1
0
Forkuj 0
Kod Zgłoszenia Projekty Wydania Wiki Aktywność
esp-idf/components/driver/sdspi_host.c

888 wiersze
29 KiB
C
Czysty Zwykły widok Historia

Replace all DOS line endings with Unix Command run was: git ls-tree -r HEAD --name-only | xargs dos2unix
2018-07-04 23:01:03 +00:00
// Copyright 2015-2017 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <stdbool.h>
#include <stddef.h>
#include <sys/param.h>
#include "esp_log.h"
#include "esp_heap_caps.h"
#include "driver/gpio.h"
#include "driver/sdmmc_defs.h"
#include "driver/sdspi_host.h"
#include "sdspi_private.h"
#include "sdspi_crc.h"
#include "esp_timer.h"
/// Max number of transactions in flight (used in start_command_write_blocks)
#define SDSPI_TRANSACTION_COUNT 4
#define SDSPI_MOSI_IDLE_VAL 0xff //!< Data value which causes MOSI to stay high
#define GPIO_UNUSED 0xff //!< Flag indicating that CD/WP is unused
/// Size of the buffer returned by get_block_buf
#define SDSPI_BLOCK_BUF_SIZE (SDSPI_MAX_DATA_LEN + 4)
/// Maximum number of dummy bytes between the request and response (minimum is 1)
#define SDSPI_RESPONSE_MAX_DELAY 8
/// Structure containing run time configuration for a single SD slot
typedef struct {
spi_device_handle_t handle; //!< SPI device handle, used for transactions
uint8_t gpio_cs; //!< CS GPIO
uint8_t gpio_cd; //!< Card detect GPIO, or GPIO_UNUSED
uint8_t gpio_wp; //!< Write protect GPIO, or GPIO_UNUSED
/// Set to 1 if the higher layer has asked the card to enable CRC checks
uint8_t data_crc_enabled : 1;
/// Number of transactions in 'transactions' array which are in use
uint8_t used_transaction_count: 3;
/// Intermediate buffer used when application buffer is not in DMA memory;
/// allocated on demand, SDSPI_BLOCK_BUF_SIZE bytes long. May be zero.
uint8_t* block_buf;
/// array with SDSPI_TRANSACTION_COUNT transaction structures
spi_transaction_t* transactions;
} slot_info_t;
static slot_info_t s_slots[3];
static const char *TAG = "sdspi_host";
/// Functions to send out different kinds of commands
static esp_err_t start_command_read_blocks(int slot, sdspi_hw_cmd_t *cmd,
uint8_t *data, uint32_t rx_length);
static esp_err_t start_command_write_blocks(int slot, sdspi_hw_cmd_t *cmd,
const uint8_t *data, uint32_t tx_length);
static esp_err_t start_command_default(int slot, int flags, sdspi_hw_cmd_t *cmd);
static esp_err_t poll_cmd_response(int slot, sdspi_hw_cmd_t *cmd);
/// A few helper functions
/// Set CS high for given slot
static void cs_high(int slot)
{
gpio_set_level(s_slots[slot].gpio_cs, 1);
}
/// Set CS low for given slot
static void cs_low(int slot)
{
gpio_set_level(s_slots[slot].gpio_cs, 0);
}
/// Return true if WP pin is configured and is low
static bool card_write_protected(int slot)
{
if (s_slots[slot].gpio_wp == GPIO_UNUSED) {
return false;
}
return gpio_get_level(s_slots[slot].gpio_wp) == 0;
}
/// Return true if CD pin is configured and is high
static bool card_missing(int slot)
{
if (s_slots[slot].gpio_cd == GPIO_UNUSED) {
return false;
}
return gpio_get_level(s_slots[slot].gpio_cd) == 1;
}
/// Check if slot number is within bounds
static bool is_valid_slot(int slot)
{
return slot == VSPI_HOST || slot == HSPI_HOST;
}
static spi_device_handle_t spi_handle(int slot)
{
return s_slots[slot].handle;
}
static bool is_slot_initialized(int slot)
{
return spi_handle(slot) != NULL;
}
static bool data_crc_enabled(int slot)
{
return s_slots[slot].data_crc_enabled;
}
/// Get pointer to a block of DMA memory, allocate if necessary.
/// This is used if the application provided buffer is not in DMA capable memory.
static esp_err_t get_block_buf(int slot, uint8_t** out_buf)
{
if (s_slots[slot].block_buf == NULL) {
s_slots[slot].block_buf = heap_caps_malloc(SDSPI_BLOCK_BUF_SIZE, MALLOC_CAP_DMA);
if (s_slots[slot].block_buf == NULL) {
return ESP_ERR_NO_MEM;
}
}
*out_buf = s_slots[slot].block_buf;
return ESP_OK;
}
static spi_transaction_t* get_transaction(int slot)
{
size_t used_transaction_count = s_slots[slot].used_transaction_count;
assert(used_transaction_count < SDSPI_TRANSACTION_COUNT);
spi_transaction_t* ret = &s_slots[slot].transactions[used_transaction_count];
++s_slots[slot].used_transaction_count;
return ret;
}
static void release_transaction(int slot)
{
--s_slots[slot].used_transaction_count;
}
static void wait_for_transactions(int slot)
{
size_t used_transaction_count = s_slots[slot].used_transaction_count;
for (size_t i = 0; i < used_transaction_count; ++i) {
spi_transaction_t* t_out;
spi_device_get_trans_result(spi_handle(slot), &t_out, portMAX_DELAY);
release_transaction(slot);
}
}
/// Clock out one byte (CS has to be high) to make the card release MISO
/// (clocking one bit would work as well, but that triggers a bug in SPI DMA)
static void release_bus(int slot)
{
spi_transaction_t t = {
.flags = SPI_TRANS_USE_RXDATA | SPI_TRANS_USE_TXDATA,
.length = 8,
.tx_data = {0xff}
};
spi_device_transmit(spi_handle(slot), &t);
// don't care if this failed
}
/// Clock out 80 cycles (10 bytes) before GO_IDLE command
static void go_idle_clockout(int slot)
{
//actually we need 10, declare 12 to meet requirement of RXDMA
uint8_t data[12];
memset(data, 0xff, sizeof(data));
spi_transaction_t t = {
.length = 10*8,
.tx_buffer = data,
.rx_buffer = data,
};
spi_device_transmit(spi_handle(slot), &t);
// don't care if this failed
}
/// Return true if the pointer can be used for DMA
static bool ptr_dma_compatible(const void* ptr)
{
return (uintptr_t) ptr >= 0x3FFAE000 &&
(uintptr_t) ptr < 0x40000000;
}
/**
* Initialize SPI device. Used to change clock speed.
* @param slot SPI host number
* @param clock_speed_hz clock speed, Hz
* @return ESP_OK on success
*/
static esp_err_t init_spi_dev(int slot, int clock_speed_hz)
{
if (spi_handle(slot)) {
// Reinitializing
spi_bus_remove_device(spi_handle(slot));
s_slots[slot].handle = NULL;
}
spi_device_interface_config_t devcfg = {
.clock_speed_hz = clock_speed_hz,
.mode = 0,
// For SD cards, CS must stay low during the whole read/write operation,
// rather than a single SPI transaction.
.spics_io_num = -1,
.queue_size = SDSPI_TRANSACTION_COUNT,
};
return spi_bus_add_device((spi_host_device_t) slot, &devcfg, &s_slots[slot].handle);
}
esp_err_t sdspi_host_init()
{
return ESP_OK;
}
esp_err_t sdspi_host_deinit()
{
for (size_t i = 0; i < sizeof(s_slots)/sizeof(s_slots[0]); ++i) {
if (s_slots[i].handle) {
spi_bus_remove_device(s_slots[i].handle);
free(s_slots[i].block_buf);
s_slots[i].block_buf = NULL;
free(s_slots[i].transactions);
s_slots[i].transactions = NULL;
spi_bus_free((spi_host_device_t) i);
s_slots[i].handle = NULL;
}
}
return ESP_OK;
}
esp_err_t sdspi_host_set_card_clk(int slot, uint32_t freq_khz)
{
if (!is_valid_slot(slot)) {
return ESP_ERR_INVALID_ARG;
}
if (!is_slot_initialized(slot)) {
return ESP_ERR_INVALID_STATE;
}
ESP_LOGD(TAG, "Setting card clock to %d kHz", freq_khz);
return init_spi_dev(slot, freq_khz * 1000);
}
esp_err_t sdspi_host_init_slot(int slot, const sdspi_slot_config_t* slot_config)
{
ESP_LOGD(TAG, "%s: SPI%d miso=%d mosi=%d sck=%d cs=%d cd=%d wp=%d, dma_ch=%d",
__func__, slot + 1,
slot_config->gpio_miso, slot_config->gpio_mosi,
slot_config->gpio_sck, slot_config->gpio_cs,
slot_config->gpio_cd, slot_config->gpio_wp,
slot_config->dma_channel);
spi_host_device_t host = (spi_host_device_t) slot;
if (!is_valid_slot(slot)) {
return ESP_ERR_INVALID_ARG;
}
spi_bus_config_t buscfg = {
.miso_io_num = slot_config->gpio_miso,
.mosi_io_num = slot_config->gpio_mosi,
.sclk_io_num = slot_config->gpio_sck,
.quadwp_io_num = -1,
.quadhd_io_num = -1
};
// Initialize SPI bus
esp_err_t ret = spi_bus_initialize((spi_host_device_t)slot, &buscfg,
slot_config->dma_channel);
if (ret != ESP_OK) {
ESP_LOGD(TAG, "spi_bus_initialize failed with rc=0x%x", ret);
return ret;
}
// Attach the SD card to the SPI bus
ret = init_spi_dev(slot, SDMMC_FREQ_PROBING * 1000);
if (ret != ESP_OK) {
ESP_LOGD(TAG, "spi_bus_add_device failed with rc=0x%x", ret);
spi_bus_free(host);
return ret;
}
// Configure CS pin
s_slots[slot].gpio_cs = (uint8_t) slot_config->gpio_cs;
gpio_config_t io_conf = {
.intr_type = GPIO_PIN_INTR_DISABLE,
.mode = GPIO_MODE_OUTPUT,
.pin_bit_mask = 1LL << slot_config->gpio_cs,
};
ret = gpio_config(&io_conf);
if (ret != ESP_OK) {
ESP_LOGD(TAG, "gpio_config (CS) failed with rc=0x%x", ret);
spi_bus_remove_device(spi_handle(slot));
s_slots[slot].handle = NULL;
spi_bus_free(host);
return ret;
}
cs_high(slot);
// Configure CD and WP pins
io_conf = (gpio_config_t) {
.intr_type = GPIO_PIN_INTR_DISABLE,
.mode = GPIO_MODE_INPUT,
.pin_bit_mask = 0,
.pull_up_en = true
};
if (slot_config->gpio_cd != SDSPI_SLOT_NO_CD) {
io_conf.pin_bit_mask |= (1 << slot_config->gpio_cd);
s_slots[slot].gpio_cd = slot_config->gpio_cd;
} else {
s_slots[slot].gpio_cd = GPIO_UNUSED;
}
if (slot_config->gpio_wp != SDSPI_SLOT_NO_WP) {
io_conf.pin_bit_mask |= (1 << slot_config->gpio_wp);
s_slots[slot].gpio_wp = slot_config->gpio_wp;
} else {
s_slots[slot].gpio_wp = GPIO_UNUSED;
}
if (io_conf.pin_bit_mask != 0) {
ret = gpio_config(&io_conf);
if (ret != ESP_OK) {
ESP_LOGD(TAG, "gpio_config (CD/WP) failed with rc=0x%x", ret);
spi_bus_remove_device(spi_handle(slot));
s_slots[slot].handle = NULL;
spi_bus_free(host);
return ret;
}
}
s_slots[slot].transactions = calloc(SDSPI_TRANSACTION_COUNT, sizeof(spi_transaction_t));
if (s_slots[slot].transactions == NULL) {
spi_bus_remove_device(spi_handle(slot));
s_slots[slot].handle = NULL;
spi_bus_free(host);
return ESP_ERR_NO_MEM;
}
return ESP_OK;
}
esp_err_t sdspi_host_start_command(int slot, sdspi_hw_cmd_t *cmd, void *data,
uint32_t data_size, int flags)
{
if (!is_valid_slot(slot)) {
return ESP_ERR_INVALID_ARG;
}
if (!is_slot_initialized(slot)) {
return ESP_ERR_INVALID_STATE;
}
if (card_missing(slot)) {
return ESP_ERR_NOT_FOUND;
}
// save some parts of cmd, as its contents will be overwritten
int cmd_index = cmd->cmd_index;
uint32_t cmd_arg;
memcpy(&cmd_arg, cmd->arguments, sizeof(cmd_arg));
cmd_arg = __builtin_bswap32(cmd_arg);
ESP_LOGV(TAG, "%s: slot=%i, CMD%d, arg=0x%08x flags=0x%x, data=%p, data_size=%i crc=0x%02x",
__func__, slot, cmd_index, cmd_arg, flags, data, data_size, cmd->crc7);
// For CMD0, clock out 80 cycles to help the card enter idle state,
// *before* CS is asserted.
if (cmd_index == MMC_GO_IDLE_STATE) {
go_idle_clockout(slot);
}
// actual transaction
esp_err_t ret = ESP_OK;
cs_low(slot);
if (flags & SDSPI_CMD_FLAG_DATA) {
if (flags & SDSPI_CMD_FLAG_WRITE) {
ret = start_command_write_blocks(slot, cmd, data, data_size);
} else {
ret = start_command_read_blocks(slot, cmd, data, data_size);
}
} else {
ret = start_command_default(slot, flags, cmd);
}
cs_high(slot);
release_bus(slot);
if (ret != ESP_OK) {
ESP_LOGD(TAG, "%s: cmd=%d error=0x%x", __func__, cmd_index, ret);
} else {
// Update internal state when some commands are sent successfully
if (cmd_index == SD_CRC_ON_OFF) {
s_slots[slot].data_crc_enabled = (uint8_t) cmd_arg;
ESP_LOGD(TAG, "data CRC set=%d", s_slots[slot].data_crc_enabled);
}
}
return ret;
}
static esp_err_t start_command_default(int slot, int flags, sdspi_hw_cmd_t *cmd)
{
size_t cmd_size = SDSPI_CMD_R1_SIZE;
if ((flags & SDSPI_CMD_FLAG_RSP_R1) ||
(flags & SDSPI_CMD_FLAG_NORSP)) {
cmd_size = SDSPI_CMD_R1_SIZE;
} else if (flags & SDSPI_CMD_FLAG_RSP_R2) {
cmd_size = SDSPI_CMD_R2_SIZE;
} else if (flags & SDSPI_CMD_FLAG_RSP_R3) {
cmd_size = SDSPI_CMD_R3_SIZE;
} else if (flags & SDSPI_CMD_FLAG_RSP_R7) {
cmd_size = SDSPI_CMD_R7_SIZE;
}
spi_transaction_t t = {
.flags = 0,
.length = cmd_size * 8,
.tx_buffer = cmd,
.rx_buffer = cmd
};
esp_err_t ret = spi_device_transmit(spi_handle(slot), &t);
if (cmd->cmd_index == MMC_STOP_TRANSMISSION) {
/* response is a stuff byte from previous transfer, ignore it */
cmd->r1 = 0xff;
}
if (ret != ESP_OK) {
ESP_LOGD(TAG, "%s: spi_device_transmit returned 0x%x", __func__, ret);
return ret;
}
if (flags & SDSPI_CMD_FLAG_NORSP) {
/* no (correct) response expected from the card, so skip polling loop */
ESP_LOGV(TAG, "%s: ignoring response byte", __func__);
cmd->r1 = 0x00;
}
ret = poll_cmd_response(slot, cmd);
if (ret != ESP_OK) {
ESP_LOGD(TAG, "%s: poll_cmd_response returned 0x%x", __func__, ret);
return ret;
}
return ESP_OK;
}
// Wait until MISO goes high
static esp_err_t poll_busy(int slot, spi_transaction_t* t, int timeout_ms)
{
uint8_t t_rx;
*t = (spi_transaction_t) {
.tx_buffer = &t_rx,
.flags = SPI_TRANS_USE_RXDATA, //data stored in rx_data
.length = 8,
};
esp_err_t ret;
uint64_t t_end = esp_timer_get_time() + timeout_ms * 1000;
int nonzero_count = 0;
do {
t_rx = SDSPI_MOSI_IDLE_VAL;
t->rx_data[0] = 0;
ret = spi_device_transmit(spi_handle(slot), t);
if (ret != ESP_OK) {
return ret;
}
if (t->rx_data[0] != 0) {
if (++nonzero_count == 2) {
return ESP_OK;
}
}
} while(esp_timer_get_time() < t_end);
ESP_LOGD(TAG, "%s: timeout", __func__);
return ESP_ERR_TIMEOUT;
}
// Wait for response token
static esp_err_t poll_response_token(int slot, spi_transaction_t* t, int timeout_ms)
{
uint8_t t_rx;
*t = (spi_transaction_t) {
.tx_buffer = &t_rx,
.flags = SPI_TRANS_USE_RXDATA,
.length = 8,
};
esp_err_t ret;
uint64_t t_end = esp_timer_get_time() + timeout_ms * 1000;
do {
t_rx = SDSPI_MOSI_IDLE_VAL;
t->rx_data[0] = 0;
ret = spi_device_transmit(spi_handle(slot), t);
if (ret != ESP_OK) {
return ret;
}
if ((t->rx_data[0] & TOKEN_RSP_MASK) == TOKEN_RSP_OK) {
return ESP_OK;
}
if ((t->rx_data[0] & TOKEN_RSP_MASK) == TOKEN_RSP_CRC_ERR) {
return ESP_ERR_INVALID_CRC;
}
if ((t->rx_data[0] & TOKEN_RSP_MASK) == TOKEN_RSP_WRITE_ERR) {
return ESP_ERR_INVALID_RESPONSE;
}
} while (esp_timer_get_time() < t_end);
ESP_LOGD(TAG, "%s: timeout", __func__);
return ESP_ERR_TIMEOUT;
}
// Wait for data token, reading 8 bytes at a time.
// If the token is found, write all subsequent bytes to extra_ptr,
// and store the number of bytes written to extra_size.
static esp_err_t poll_data_token(int slot, spi_transaction_t* t,
uint8_t* extra_ptr, size_t* extra_size, int timeout_ms)
{
uint8_t t_rx[8];
*t = (spi_transaction_t) {
.tx_buffer = &t_rx,
.rx_buffer = &t_rx,
.length = sizeof(t_rx) * 8,
};
esp_err_t ret;
uint64_t t_end = esp_timer_get_time() + timeout_ms * 1000;
do {
memset(t_rx, SDSPI_MOSI_IDLE_VAL, sizeof(t_rx));
ret = spi_device_transmit(spi_handle(slot), t);
if (ret != ESP_OK) {
return ret;
}
bool found = false;
for (int byte_idx = 0; byte_idx < sizeof(t_rx); byte_idx++) {
uint8_t rd_data = t_rx[byte_idx];
if (rd_data == TOKEN_BLOCK_START) {
found = true;
memcpy(extra_ptr, t_rx + byte_idx + 1, sizeof(t_rx) - byte_idx - 1);
*extra_size = sizeof(t_rx) - byte_idx - 1;
break;
}
if (rd_data != 0xff && rd_data != 0) {
ESP_LOGD(TAG, "%s: received 0x%02x while waiting for data",
__func__, rd_data);
return ESP_ERR_INVALID_RESPONSE;
}
}
if (found) {
return ESP_OK;
}
} while (esp_timer_get_time() < t_end);
ESP_LOGD(TAG, "%s: timeout", __func__);
return ESP_ERR_TIMEOUT;
}
static esp_err_t poll_cmd_response(int slot, sdspi_hw_cmd_t *cmd)
{
int response_delay_bytes = SDSPI_RESPONSE_MAX_DELAY;
while ((cmd->r1 & SD_SPI_R1_NO_RESPONSE) != 0 && response_delay_bytes-- > 0) {
spi_transaction_t* t = get_transaction(slot);
*t = (spi_transaction_t) {
.flags = SPI_TRANS_USE_RXDATA | SPI_TRANS_USE_TXDATA,
.length = 8,
};
t->tx_data[0] = 0xff;
esp_err_t ret = spi_device_transmit(spi_handle(slot), t);
uint8_t r1 = t->rx_data[0];
release_transaction(slot);
if (ret != ESP_OK) {
return ret;
}
cmd->r1 = r1;
}
if (cmd->r1 & SD_SPI_R1_NO_RESPONSE) {
return ESP_ERR_TIMEOUT;
}
return ESP_OK;
}
/**
* Receiving one or more blocks of data happens as follows:
* 1. send command + receive r1 response (SDSPI_CMD_R1_SIZE bytes total)
* 2. keep receiving bytes until TOKEN_BLOCK_START is encountered (this may
* take a while, depending on card's read speed)
* 3. receive up to SDSPI_MAX_DATA_LEN = 512 bytes of actual data
* 4. receive 2 bytes of CRC
* 5. for multi block transfers, go to step 2
*
* These steps can be done separately, but that leads to a less than optimal
* performance on large transfers because of delays between each step.
* For example, if steps 3 and 4 are separate SPI transactions queued one after
* another, there will be ~16 microseconds of dead time between end of step 3
* and the beginning of step 4. A delay between two blocking SPI transactions
* in step 2 is even higher (~60 microseconds).
*
* To improve read performance the following sequence is adopted:
* 1. Do the first transfer: command + r1 response + 8 extra bytes.
* Set pre_scan_data_ptr to point to the 8 extra bytes, and set
* pre_scan_data_size to 8.
* 2. Search pre_scan_data_size bytes for TOKEN_BLOCK_START.
* If found, the rest of the bytes contain part of the actual data.
* Store pointer to and size of that extra data as extra_data_{ptr,size}.
* If not found, fall back to polling for TOKEN_BLOCK_START, 8 bytes at a
* time (in poll_data_token function). Deal with extra data in the same way,
* by setting extra_data_{ptr,size}.
* 3. Receive the remaining 512 - extra_data_size bytes, plus 4 extra bytes
* (i.e. 516 - extra_data_size). Of the 4 extra bytes, first two will capture
* the CRC value, and the other two will capture 0xff 0xfe sequence
* indicating the start of the next block. Actual scanning is done by
* setting pre_scan_data_ptr to point to these last 2 bytes, and setting
* pre_scan_data_size = 2, then going to step 2 to receive the next block.
* When the final block is being received, the number of extra bytes is 2
* (only for CRC), because we don't need to wait for start token of the
* next block, and some cards are getting confused by these two extra bytes.
*
* With this approach the delay between blocks of a multi-block transfer is
* ~95 microseconds, out of which 35 microseconds are spend doing the CRC check.
* Further speedup is possible by pipelining transfers and CRC checks, at an
* expense of one extra temporary buffer.
*/
static esp_err_t start_command_read_blocks(int slot, sdspi_hw_cmd_t *cmd,
uint8_t *data, uint32_t rx_length)
{
bool need_stop_command = rx_length > SDSPI_MAX_DATA_LEN;
spi_transaction_t* t_command = get_transaction(slot);
*t_command = (spi_transaction_t) {
.length = (SDSPI_CMD_R1_SIZE + SDSPI_RESPONSE_MAX_DELAY) * 8,
.tx_buffer = cmd,
.rx_buffer = cmd,
};
esp_err_t ret = spi_device_transmit(spi_handle(slot), t_command);
if (ret != ESP_OK) {
return ret;
}
release_transaction(slot);
uint8_t* cmd_u8 = (uint8_t*) cmd;
size_t pre_scan_data_size = SDSPI_RESPONSE_MAX_DELAY;
uint8_t* pre_scan_data_ptr = cmd_u8 + SDSPI_CMD_R1_SIZE;
/* R1 response is delayed by 1-8 bytes from the request.
* This loop searches for the response and writes it to cmd->r1.
*/
while ((cmd->r1 & SD_SPI_R1_NO_RESPONSE) != 0 && pre_scan_data_size > 0) {
cmd->r1 = *pre_scan_data_ptr;
++pre_scan_data_ptr;
--pre_scan_data_size;
}
if (cmd->r1 & SD_SPI_R1_NO_RESPONSE) {
ESP_LOGD(TAG, "no response token found");
return ESP_ERR_TIMEOUT;
}
while (rx_length > 0) {
size_t extra_data_size = 0;
const uint8_t* extra_data_ptr = NULL;
bool need_poll = true;
for (int i = 0; i < pre_scan_data_size; ++i) {
if (pre_scan_data_ptr[i] == TOKEN_BLOCK_START) {
extra_data_size = pre_scan_data_size - i - 1;
extra_data_ptr = pre_scan_data_ptr + i + 1;
need_poll = false;
break;
}
}
if (need_poll) {
// Wait for data to be ready
spi_transaction_t* t_poll = get_transaction(slot);
ret = poll_data_token(slot, t_poll, cmd_u8 + SDSPI_CMD_R1_SIZE, &extra_data_size, cmd->timeout_ms);
release_transaction(slot);
if (ret != ESP_OK) {
return ret;
}
if (extra_data_size) {
extra_data_ptr = cmd_u8 + SDSPI_CMD_R1_SIZE;
}
}
// Arrange RX buffer
size_t will_receive = MIN(rx_length, SDSPI_MAX_DATA_LEN) - extra_data_size;
uint8_t* rx_data;
ret = get_block_buf(slot, &rx_data);
if (ret != ESP_OK) {
return ret;
}
// receive actual data
const size_t receive_extra_bytes = (rx_length > SDSPI_MAX_DATA_LEN) ? 4 : 2;
memset(rx_data, 0xff, will_receive + receive_extra_bytes);
spi_transaction_t* t_data = get_transaction(slot);
*t_data = (spi_transaction_t) {
.length = (will_receive + receive_extra_bytes) * 8,
.rx_buffer = rx_data,
.tx_buffer = rx_data
};
ret = spi_device_transmit(spi_handle(slot), t_data);
if (ret != ESP_OK) {
return ret;
}
release_transaction(slot);
// CRC bytes need to be received even if CRC is not enabled
uint16_t crc = UINT16_MAX;
memcpy(&crc, rx_data + will_receive, sizeof(crc));
// Bytes to scan for the start token
pre_scan_data_size = receive_extra_bytes - sizeof(crc);
pre_scan_data_ptr = rx_data + will_receive + sizeof(crc);
// Copy data to the destination buffer
memcpy(data + extra_data_size, rx_data, will_receive);
if (extra_data_size) {
memcpy(data, extra_data_ptr, extra_data_size);
}
// compute CRC of the received data
uint16_t crc_of_data = 0;
if (data_crc_enabled(slot)) {
crc_of_data = sdspi_crc16(data, will_receive + extra_data_size);
if (crc_of_data != crc) {
ESP_LOGE(TAG, "data CRC failed, got=0x%04x expected=0x%04x", crc_of_data, crc);
esp_log_buffer_hex(TAG, data, 16);
return ESP_ERR_INVALID_CRC;
}
}
data += will_receive + extra_data_size;
rx_length -= will_receive + extra_data_size;
extra_data_size = 0;
extra_data_ptr = NULL;
}
if (need_stop_command) {
// To end multi block transfer, send stop command and wait for the
// card to process it
sdspi_hw_cmd_t stop_cmd;
make_hw_cmd(MMC_STOP_TRANSMISSION, 0, cmd->timeout_ms, &stop_cmd);
ret = start_command_default(slot, SDSPI_CMD_FLAG_RSP_R1, &stop_cmd);
if (ret != ESP_OK) {
return ret;
}
if (stop_cmd.r1 != 0) {
ESP_LOGD(TAG, "%s: STOP_TRANSMISSION response 0x%02x", __func__, stop_cmd.r1);
}
spi_transaction_t* t_poll = get_transaction(slot);
ret = poll_busy(slot, t_poll, cmd->timeout_ms);
release_transaction(slot);
if (ret != ESP_OK) {
return ret;
}
}
return ESP_OK;
}
static esp_err_t start_command_write_blocks(int slot, sdspi_hw_cmd_t *cmd,
const uint8_t *data, uint32_t tx_length)
{
if (card_write_protected(slot)) {
ESP_LOGW(TAG, "%s: card write protected", __func__);
return ESP_ERR_INVALID_STATE;
}
spi_transaction_t* t_command = get_transaction(slot);
*t_command = (spi_transaction_t) {
.length = SDSPI_CMD_R1_SIZE * 8,
.tx_buffer = cmd,
.rx_buffer = cmd,
};
esp_err_t ret = spi_device_queue_trans(spi_handle(slot), t_command, 0);
if (ret != ESP_OK) {
return ret;
}
wait_for_transactions(slot);
// Poll for command response which may be delayed up to 8 bytes
ret = poll_cmd_response(slot, cmd);
if (ret != ESP_OK) {
ESP_LOGD(TAG, "%s: poll_cmd_response returned 0x%x", __func__, ret);
return ret;
}
uint8_t start_token = tx_length <= SDSPI_MAX_DATA_LEN ?
TOKEN_BLOCK_START : TOKEN_BLOCK_START_WRITE_MULTI;
while (tx_length > 0) {
// Write block start token
spi_transaction_t* t_start_token = get_transaction(slot);
*t_start_token = (spi_transaction_t) {
.length = sizeof(start_token) * 8,
.tx_buffer = &start_token
};
ret = spi_device_queue_trans(spi_handle(slot), t_start_token, 0);
if (ret != ESP_OK) {
return ret;
}
// Prepare data to be sent
size_t will_send = MIN(tx_length, SDSPI_MAX_DATA_LEN);
const uint8_t* tx_data = data;
if (!ptr_dma_compatible(tx_data)) {
// If the pointer can't be used with DMA, copy data into a new buffer
uint8_t* tmp;
ret = get_block_buf(slot, &tmp);
if (ret != ESP_OK) {
return ret;
}
memcpy(tmp, tx_data, will_send);
tx_data = tmp;
}
// Write data
spi_transaction_t* t_data = get_transaction(slot);
*t_data = (spi_transaction_t) {
.length = will_send * 8,
.tx_buffer = tx_data,
};
ret = spi_device_queue_trans(spi_handle(slot), t_data, 0);
if (ret != ESP_OK) {
return ret;
}
// Write CRC
uint16_t crc = sdspi_crc16(data, will_send);
spi_transaction_t* t_crc = get_transaction(slot);
*t_crc = (spi_transaction_t) {
.length = sizeof(crc) * 8,
.tx_buffer = (uint8_t*) &crc,
};
ret = spi_device_queue_trans(spi_handle(slot), t_crc, 0);
if (ret != ESP_OK) {
return ret;
}
// Wait for data to be sent
wait_for_transactions(slot);
// Poll for response
spi_transaction_t* t_poll = get_transaction(slot);
ret = poll_response_token(slot, t_poll, cmd->timeout_ms);
release_transaction(slot);
if (ret != ESP_OK) {
return ret;
}
// Wait for the card to finish writing data
t_poll = get_transaction(slot);
ret = poll_busy(slot, t_poll, cmd->timeout_ms);
release_transaction(slot);
if (ret != ESP_OK) {
return ret;
}
tx_length -= will_send;
data += will_send;
}
if (start_token == TOKEN_BLOCK_START_WRITE_MULTI) {
uint8_t stop_token[2] = {
TOKEN_BLOCK_STOP_WRITE_MULTI,
SDSPI_MOSI_IDLE_VAL
};
spi_transaction_t* t_stop_token = get_transaction(slot);
*t_stop_token = (spi_transaction_t) {
.length = sizeof(stop_token) * 8,
.tx_buffer = &stop_token,
};
ret = spi_device_queue_trans(spi_handle(slot), t_stop_token, 0);
if (ret != ESP_OK) {
return ret;
}
wait_for_transactions(slot);
spi_transaction_t* t_poll = get_transaction(slot);
ret = poll_busy(slot, t_poll, cmd->timeout_ms);
release_transaction(slot);
if (ret != ESP_OK) {
return ret;
}
}
return ESP_OK;
}