kopia lustrzana https://github.com/espressif/esp-idf
68 wiersze
2.3 KiB
Markdown
68 wiersze
2.3 KiB
Markdown
|
# ADC DMA Example
|
||
|
|
|
||
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
||
|
|
|
||
|
|
This example shows how to use ADC Continuous Read Mode (DMA Mode) to read from GPIO pins via on-chip ADC module(s).
|
||
|
|
|
||
|
|
## How to use example
|
||
|
|
|
||
|
|
### Hardware Required
|
||
|
|
|
||
|
|
* A development board with ESP32, ESP32-S and ESP32-C SoC
|
||
|
|
* A USB cable for power supply and programming
|
||
|
|
|
||
|
|
Please refer to the `channel` array defined in `adc_dma_example_main.c`. These GPIOs should be connected to voltage sources (0 ~ 3.3V). If other ADC unit(s) / channel(s) are selected in your application,
|
||
|
|
feel free to modify these definitions.
|
||
|
|
|
||
|
|
### Configure the project
|
||
|
|
|
||
|
|
```
|
||
|
|
idf.py menuconfig
|
||
|
|
```
|
||
|
|
|
||
|
|
### Build and Flash
|
||
|
|
|
||
|
|
Build the project and flash it to the board, then run monitor tool to view serial output:
|
||
|
|
|
||
|
|
```
|
||
|
|
idf.py -p PORT flash monitor
|
||
|
|
```
|
||
|
|
|
||
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
||
|
|
|
||
|
|
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
|
||
|
|
|
||
|
|
## Example Output
|
||
|
|
|
||
|
|
Running this example, you will see the following log output on the serial monitor:
|
||
|
|
```
|
||
|
|
I (338) ADC DMA: adc_pattern[0].atten is :0
|
||
|
|
I (348) ADC DMA: adc_pattern[0].channel is :2
|
||
|
|
I (348) ADC DMA: adc_pattern[0].unit is :0
|
||
|
|
I (358) ADC DMA: adc_pattern[1].atten is :0
|
||
|
|
I (358) ADC DMA: adc_pattern[1].channel is :3
|
||
|
|
I (368) ADC DMA: adc_pattern[1].unit is :0
|
||
|
|
I (368) ADC DMA: adc_pattern[2].atten is :0
|
||
|
|
I (378) ADC DMA: adc_pattern[2].channel is :0
|
||
|
|
I (378) ADC DMA: adc_pattern[2].unit is :1
|
||
|
|
I (388) TASK:: ret is 0, ret_num is 256
|
||
|
|
I (388) ADC DMA: Unit: 1,_Channel: 2, Value: bec
|
||
|
|
I (398) ADC DMA: Unit: 2,_Channel: 0, Value: 9cb
|
||
|
|
I (398) ADC DMA: Unit: 1,_Channel: 3, Value: acb
|
||
|
|
I (408) ADC DMA: Unit: 2,_Channel: 0, Value: 966
|
||
|
|
I (408) ADC DMA: Unit: 1,_Channel: 2, Value: b63
|
||
|
|
I (418) ADC DMA: Unit: 2,_Channel: 0, Value: 8ff
|
||
|
|
I (418) ADC DMA: Unit: 1,_Channel: 3, Value: a6b
|
||
|
|
I (428) ADC DMA: Unit: 2,_Channel: 0, Value: 8a2
|
||
|
|
...
|
||
|
|
```
|
||
|
|
|
||
|
|
## Troubleshooting
|
||
|
|
|
||
|
|
* program upload failure
|
||
|
|
|
||
|
|
* Hardware connection is not correct: run `idf.py -p PORT monitor`, and reboot your board to see if there are any output logs.
|
||
|
|
* The baud rate for downloading is too high: lower your baud rate in the `menuconfig` menu, and try again.
|
||
|
|
|
||
|
|
For any technical queries, please open an [issue](https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you soon.
|