kopia lustrzana https://github.com/espressif/esp-idf
300 wiersze
11 KiB
C
300 wiersze
11 KiB
C
![]() |
/*
|
||
|
* copyright (c) Espressif System 2019
|
||
|
*
|
||
|
*/
|
||
|
|
||
|
#ifndef _ROM_OPI_FLASH_H_
|
||
|
#define _ROM_OPI_FLASH_H_
|
||
|
#include <stdio.h>
|
||
|
#include <string.h>
|
||
|
#include <stdint.h>
|
||
|
#include "spi_flash.h"
|
||
|
|
||
|
#ifdef __cplusplus
|
||
|
extern "C" {
|
||
|
#endif
|
||
|
|
||
|
typedef struct {
|
||
|
uint16_t cmd; /*!< Command value */
|
||
|
uint16_t cmdBitLen; /*!< Command byte length*/
|
||
|
uint32_t *addr; /*!< Point to address value*/
|
||
|
uint32_t addrBitLen; /*!< Address byte length*/
|
||
|
uint32_t *txData; /*!< Point to send data buffer*/
|
||
|
uint32_t txDataBitLen; /*!< Send data byte length.*/
|
||
|
uint32_t *rxData; /*!< Point to recevie data buffer*/
|
||
|
uint32_t rxDataBitLen; /*!< Recevie Data byte length.*/
|
||
|
uint32_t dummyBitLen;
|
||
|
} esp_rom_spi_cmd_t;
|
||
|
|
||
|
#define ESP_ROM_OPIFLASH_MUX_TAKE()
|
||
|
#define ESP_ROM_OPIFLASH_MUX_GIVE()
|
||
|
#define ESP_ROM_OPIFLASH_SEL_CS0 (BIT(0))
|
||
|
#define ESP_ROM_OPIFLASH_SEL_CS1 (BIT(1))
|
||
|
|
||
|
// Definition of MX25UM25645G Octa Flash
|
||
|
// SPI status register
|
||
|
#define ESP_ROM_SPIFLASH_BUSY_FLAG BIT0
|
||
|
#define ESP_ROM_SPIFLASH_WRENABLE_FLAG BIT1
|
||
|
#define ESP_ROM_SPIFLASH_BP0 BIT2
|
||
|
#define ESP_ROM_SPIFLASH_BP1 BIT3
|
||
|
#define ESP_ROM_SPIFLASH_BP2 BIT4
|
||
|
#define ESP_ROM_SPIFLASH_WR_PROTECT (ESP_ROM_SPIFLASH_BP0|ESP_ROM_SPIFLASH_BP1|ESP_ROM_SPIFLASH_BP2)
|
||
|
#define ESP_ROM_SPIFLASH_QE BIT9
|
||
|
|
||
|
#define FLASH_OP_MODE_RDCMD_DOUT 0x3B
|
||
|
#define ESP_ROM_FLASH_SECTOR_SIZE 0x1000
|
||
|
#define ESP_ROM_FLASH_BLOCK_SIZE_64K 0x10000
|
||
|
#define ESP_ROM_FLASH_PAGE_SIZE 256
|
||
|
|
||
|
// FLASH commands
|
||
|
#define ROM_FLASH_CMD_RDID 0x9F
|
||
|
#define ROM_FLASH_CMD_WRSR 0x01
|
||
|
#define ROM_FLASH_CMD_WRSR2 0x31 /* Not all SPI flash uses this command */
|
||
|
#define ROM_FLASH_CMD_WREN 0x06
|
||
|
#define ROM_FLASH_CMD_WRDI 0x04
|
||
|
#define ROM_FLASH_CMD_RDSR 0x05
|
||
|
#define ROM_FLASH_CMD_RDSR2 0x35 /* Not all SPI flash uses this command */
|
||
|
#define ROM_FLASH_CMD_ERASE_SEC 0x20
|
||
|
#define ROM_FLASH_CMD_ERASE_BLK_32K 0x52
|
||
|
#define ROM_FLASH_CMD_ERASE_BLK_64K 0xD8
|
||
|
#define ROM_FLASH_CMD_OTPEN 0x3A /* Enable OTP mode, not all SPI flash uses this command */
|
||
|
#define ROM_FLASH_CMD_RSTEN 0x66
|
||
|
#define ROM_FLASH_CMD_RST 0x99
|
||
|
|
||
|
#define ROM_FLASH_CMD_SE4B 0x21
|
||
|
#define ROM_FLASH_CMD_SE4B_OCT 0xDE21
|
||
|
#define ROM_FLASH_CMD_BE4B 0xDC
|
||
|
#define ROM_FLASH_CMD_BE4B_OCT 0x23DC
|
||
|
#define ROM_FLASH_CMD_RSTEN_OCT 0x9966
|
||
|
#define ROM_FLASH_CMD_RST_OCT 0x6699
|
||
|
|
||
|
#define ROM_FLASH_CMD_FSTRD4B_STR 0x13EC
|
||
|
#define ROM_FLASH_CMD_FSTRD4B_DTR 0x11EE
|
||
|
#define ROM_FLASH_CMD_FSTRD4B 0x0C
|
||
|
#define ROM_FLASH_CMD_PP4B 0x12
|
||
|
#define ROM_FLASH_CMD_PP4B_OCT 0xED12
|
||
|
|
||
|
#define ROM_FLASH_CMD_RDID_OCT 0x609F
|
||
|
#define ROM_FLASH_CMD_WREN_OCT 0xF906
|
||
|
#define ROM_FLASH_CMD_RDSR_OCT 0xFA05
|
||
|
#define ROM_FLASH_CMD_RDCR2 0x71
|
||
|
#define ROM_FLASH_CMD_RDCR2_OCT 0x8E71
|
||
|
#define ROM_FLASH_CMD_WRCR2 0x72
|
||
|
#define ROM_FLASH_CMD_WRCR2_OCT 0x8D72
|
||
|
|
||
|
// Definitions for GigaDevice GD25LX256E Flash
|
||
|
#define ROM_FLASH_CMD_RDFSR_GD 0x70
|
||
|
#define ROM_FLASH_CMD_RD_GD 0x03
|
||
|
#define ROM_FLASH_CMD_RD4B_GD 0x13
|
||
|
#define ROM_FLASH_CMD_FSTRD_GD 0x0B
|
||
|
#define ROM_FLASH_CMD_FSTRD4B_GD 0x0C
|
||
|
#define ROM_FLASH_CMD_FSTRD_OOUT_GD 0x8B
|
||
|
#define ROM_FLASH_CMD_FSTRD4B_OOUT_GD 0x7C
|
||
|
#define ROM_FLASH_CMD_FSTRD_OIOSTR_GD 0xCB
|
||
|
#define ROM_FLASH_CMD_FSTRD4B_OIOSTR_GD 0xCC
|
||
|
#define ROM_FLASH_CMD_FSTRD4B_OIODTR_GD 0xFD
|
||
|
|
||
|
#define ROM_FLASH_CMD_PP_GD 0x02
|
||
|
#define ROM_FLASH_CMD_PP4B_GD 0x12
|
||
|
#define ROM_FLASH_CMD_PP_OOUT_GD 0x82
|
||
|
#define ROM_FLASH_CMD_PP4B_OOUT_GD 0x84
|
||
|
#define ROM_FLASH_CMD_PP_OIO_GD 0xC2
|
||
|
#define ROM_FLASH_CMD_PP4B_OIOSTR_GD 0x8E
|
||
|
|
||
|
#define ROM_FLASH_CMD_SE_GD 0x20
|
||
|
#define ROM_FLASH_CMD_SE4B_GD 0x21
|
||
|
#define ROM_FLASH_CMD_BE32K_GD 0x52
|
||
|
#define ROM_FLASH_CMD_BE32K4B_GD 0x5C
|
||
|
#define ROM_FLASH_CMD_BE64K_GD 0xD8
|
||
|
#define ROM_FLASH_CMD_BE64K4B_GD 0xDC
|
||
|
|
||
|
#define ROM_FLASH_CMD_EN4B_GD 0xB7
|
||
|
#define ROM_FLASH_CMD_DIS4B_GD 0xE9
|
||
|
|
||
|
// spi user mode command config
|
||
|
|
||
|
/**
|
||
|
* @brief Config the spi user command
|
||
|
* @param spi_num spi port
|
||
|
* @param pcmd pointer to accept the spi command struct
|
||
|
*/
|
||
|
void esp_rom_spi_cmd_config(int spi_num, esp_rom_spi_cmd_t* pcmd);
|
||
|
|
||
|
/**
|
||
|
* @brief Start a spi user command sequence
|
||
|
* @param spi_num spi port
|
||
|
* @param rx_buf buffer pointer to receive data
|
||
|
* @param rx_len receive data length in byte
|
||
|
* @param cs_en_mask decide which cs to use, 0 for cs0, 1 for cs1
|
||
|
* @param is_write_erase to indicate whether this is a write or erase operation, since the CPU would check permission
|
||
|
*/
|
||
|
void esp_rom_spi_cmd_start(int spi_num, uint8_t* rx_buf, uint16_t rx_len, uint8_t cs_en_mask, bool is_write_erase);
|
||
|
|
||
|
/**
|
||
|
* @brief Config opi flash pads according to efuse settings.
|
||
|
*/
|
||
|
void esp_rom_opiflash_pin_config(void);
|
||
|
|
||
|
// set SPI read/write mode
|
||
|
/**
|
||
|
* @brief Set SPI operation mode
|
||
|
* @param spi_num spi port
|
||
|
* @param mode Flash Read Mode
|
||
|
*/
|
||
|
void esp_rom_spi_set_op_mode(int spi_num, esp_rom_spiflash_read_mode_t mode);
|
||
|
|
||
|
/**
|
||
|
* @brief Set data swap mode in DTR(DDR) mode
|
||
|
* @param spi_num spi port
|
||
|
* @param wr_swap to decide whether to swap fifo data in dtr write operation
|
||
|
* @param rd_swap to decide whether to swap fifo data in dtr read operation
|
||
|
*/
|
||
|
void esp_rom_spi_set_dtr_swap_mode(int spi, bool wr_swap, bool rd_swap);
|
||
|
|
||
|
|
||
|
/**
|
||
|
* @brief to send reset command in spi/opi-str/opi-dtr mode(for MX25UM25645G)
|
||
|
* @param spi_num spi port
|
||
|
*/
|
||
|
void esp_rom_opiflash_mode_reset(int spi_num);
|
||
|
|
||
|
#if 0
|
||
|
// MX25UM25645G opi flash interface
|
||
|
/**
|
||
|
* @brief To execute a flash operation command
|
||
|
* @param spi_num spi port
|
||
|
* @param mode Flash Read Mode
|
||
|
* @param cmd data to send in command field
|
||
|
* @param cmd_bit_len bit length of command field
|
||
|
* @param addr data to send in address field
|
||
|
* @param addr_bit_len bit length of address field
|
||
|
* @param dummy_bits bit length of dummy field
|
||
|
* @param mosi_data data buffer to be sent in mosi field
|
||
|
* @param mosi_bit_len bit length of data buffer to be sent in mosi field
|
||
|
* @param miso_data data buffer to accept data in miso field
|
||
|
* @param miso_bit_len bit length of data buffer to accept data in miso field
|
||
|
* @param cs_mark decide which cs pin to use. 0: cs0, 1: cs1
|
||
|
* @param is_write_erase_operation to indicate whether this a write or erase flash operation
|
||
|
*/
|
||
|
void esp_rom_opiflash_exec_cmd(int spi_num, esp_rom_spiflash_read_mode_t mode,
|
||
|
uint32_t cmd, int cmd_bit_len,
|
||
|
uint32_t addr, int addr_bit_len,
|
||
|
int dummy_bits,
|
||
|
uint8_t* mosi_data, int mosi_bit_len,
|
||
|
uint8_t* miso_data, int miso_bit_len,
|
||
|
uint32_t cs_mask,
|
||
|
bool is_write_erase_operation);
|
||
|
|
||
|
/**
|
||
|
* @brief send reset command to opi flash
|
||
|
* @param spi_num spi port
|
||
|
* @param mode Flash Operation Mode
|
||
|
*/
|
||
|
void esp_rom_opiflash_soft_reset(int spi_num, esp_rom_spiflash_read_mode_t mode);
|
||
|
|
||
|
/**
|
||
|
* @brief to read opi flash ID(for MX25UM25645G)
|
||
|
* @param spi_num spi port
|
||
|
* @param mode Flash Operation Mode
|
||
|
* @return opi flash id
|
||
|
*/
|
||
|
uint32_t esp_rom_opiflash_read_id(int spi_num, esp_rom_spiflash_read_mode_t mode);
|
||
|
|
||
|
/**
|
||
|
* @brief to read opi flash status register(for MX25UM25645G)
|
||
|
* @param spi_num spi port
|
||
|
* @param mode Flash Operation Mode
|
||
|
* @return opi flash status value
|
||
|
*/
|
||
|
uint8_t esp_rom_opiflash_rdsr(int spi_num, esp_rom_spiflash_read_mode_t mode);
|
||
|
|
||
|
/**
|
||
|
* @brief wait opi flash status register to be idle
|
||
|
* @param spi_num spi port
|
||
|
* @param mode Flash Operation Mode
|
||
|
*/
|
||
|
void esp_rom_opiflash_wait_idle(int spi_num, esp_rom_spiflash_read_mode_t mode);
|
||
|
|
||
|
/**
|
||
|
* @brief to read the config register2(for MX25UM25645G)
|
||
|
* @param spi_num spi port
|
||
|
* @param mode Flash Operation Mode
|
||
|
* @param addr the address of configure register
|
||
|
* @return value of config register2
|
||
|
*/
|
||
|
uint8_t esp_rom_opiflash_rdcr2(int spi_num, esp_rom_spiflash_read_mode_t mode, uint32_t addr);
|
||
|
|
||
|
/**
|
||
|
* @brief to write the config register2(for MX25UM25645G)
|
||
|
* @param spi_num spi port
|
||
|
* @param mode Flash Operation Mode
|
||
|
* @param addr the address of config register
|
||
|
* @param val the value to write
|
||
|
*/
|
||
|
void esp_rom_opiflash_wrcr2(int spi_num, esp_rom_spiflash_read_mode_t mode, uint32_t addr, uint8_t val);
|
||
|
|
||
|
/**
|
||
|
* @brief to erase flash sector(for MX25UM25645G)
|
||
|
* @param spi_num spi port
|
||
|
* @param address the sector address to be erased
|
||
|
* @param mode Flash operation mode
|
||
|
* @return flash operation result
|
||
|
*/
|
||
|
esp_rom_spiflash_result_t esp_rom_opiflash_erase_sector(int spi_num, uint32_t address, esp_rom_spiflash_read_mode_t mode);
|
||
|
|
||
|
/**
|
||
|
* @brief to erase flash block(for MX25UM25645G)
|
||
|
* @param spi_num spi port
|
||
|
* @param address the block address to be erased
|
||
|
* @param mode Flash operation mode
|
||
|
* @return flash operation result
|
||
|
*/
|
||
|
esp_rom_spiflash_result_t esp_rom_opiflash_erase_block_64k(int spi_num, uint32_t address, esp_rom_spiflash_read_mode_t mode);
|
||
|
|
||
|
/**
|
||
|
* @brief to erase a flash area define by start address and length(for MX25UM25645G)
|
||
|
* @param spi_num spi port
|
||
|
* @param start_addr the start address to be erased
|
||
|
* @param area_len the erea length to be erased
|
||
|
* @param mode flash operation mode
|
||
|
* @return flash operation result
|
||
|
*/
|
||
|
esp_rom_spiflash_result_t esp_rom_opiflash_erase_area(int spi_num, uint32_t start_addr, uint32_t area_len, esp_rom_spiflash_read_mode_t mode);
|
||
|
|
||
|
/**
|
||
|
* @brief to read data from opi flash(for MX25UM25645G)
|
||
|
* @param spi_num spi port
|
||
|
* @param mode flash operation mode
|
||
|
* @param flash_addr flash address to read data from
|
||
|
* @param data_addr data buffer to accept the data
|
||
|
* @param len data length to be read
|
||
|
* @return flash operation result
|
||
|
*/
|
||
|
esp_rom_spiflash_result_t esp_rom_opiflash_read(int spi_num, esp_rom_spiflash_read_mode_t mode, uint32_t flash_addr, uint8_t *data_addr, int len);
|
||
|
|
||
|
/**
|
||
|
* @brief to write data to opi flash(for MX25UM25645G)
|
||
|
* @param spi_num spi port
|
||
|
* @param mode flash operation mode
|
||
|
* @param flash_addr flash address to write data to
|
||
|
* @param data_addr data buffer to write to flash
|
||
|
* @param len data length to write
|
||
|
* @return flash operation result
|
||
|
*/
|
||
|
esp_rom_spiflash_result_t esp_rom_opiflash_write(int spi_num, esp_rom_spiflash_read_mode_t mode, uint32_t flash_addr, uint8_t *data_addr, uint32_t len);
|
||
|
|
||
|
/**
|
||
|
* @brief to set opi flash operation mode(for MX25UM25645G)
|
||
|
* @param spi_num spi port
|
||
|
* @param cur_mode current operation mode
|
||
|
* @param target the target operation mode to be set
|
||
|
*/
|
||
|
void esp_rom_opiflash_set_mode(int spi_num, esp_rom_spiflash_read_mode_t cur_mode, esp_rom_spiflash_read_mode_t target_mode);
|
||
|
#endif
|
||
|
|
||
|
#ifdef __cplusplus
|
||
|
}
|
||
|
#endif
|
||
|
|
||
|
#endif
|