DIS_FORCE_DOWNLOAD, EFUSE_BLK0, 44, 1, [] Set this bit to disable the function that forces chip into download mode
DIS_TWAI, EFUSE_BLK0, 46, 1, [DIS_CAN] Set this bit to disable CAN function
JTAG_SEL_ENABLE, EFUSE_BLK0, 47, 1, [] Set this bit to enable selection between usb_to_jtag and pad_to_jtag through strapping gpio10 when both reg_dis_usb_jtag and reg_dis_pad_jtag are equal to 0
SOFT_DIS_JTAG, EFUSE_BLK0, 48, 3, [] Set these bits to disable JTAG in the soft way (odd number 1 means disable ). JTAG can be enabled in HMAC module
DIS_PAD_JTAG, EFUSE_BLK0, 51, 1, [] Set this bit to disable JTAG in the hard way. JTAG is disabled permanently
DIS_DOWNLOAD_MANUAL_ENCRYPT, EFUSE_BLK0, 52, 1, [] Set this bit to disable flash encryption when in download boot modes
USB_EXCHG_PINS, EFUSE_BLK0, 57, 1, [] Set this bit to exchange USB D+ and D- pins
VDD_SPI_AS_GPIO, EFUSE_BLK0, 58, 1, [] Set this bit to vdd spi pin function as gpio
WDT_DELAY_SEL, EFUSE_BLK0, 80, 2, [] RTC watchdog timeout threshold; in unit of slow clock cycle {0: "40000"; 1: "80000"; 2: "160000"; 3: "320000"}
SPI_BOOT_CRYPT_CNT, EFUSE_BLK0, 82, 3, [] Enables flash encryption when 1 or 3 bits are set and disables otherwise {0: "Disable"; 1: "Enable"; 3: "Disable"; 7: "Enable"}
KEY_PURPOSE_0, EFUSE_BLK0, 88, 4, [KEY0_PURPOSE] Purpose of Key0
KEY_PURPOSE_1, EFUSE_BLK0, 92, 4, [KEY1_PURPOSE] Purpose of Key1
KEY_PURPOSE_2, EFUSE_BLK0, 96, 4, [KEY2_PURPOSE] Purpose of Key2
KEY_PURPOSE_3, EFUSE_BLK0, 100, 4, [KEY3_PURPOSE] Purpose of Key3
KEY_PURPOSE_4, EFUSE_BLK0, 104, 4, [KEY4_PURPOSE] Purpose of Key4
KEY_PURPOSE_5, EFUSE_BLK0, 108, 4, [KEY5_PURPOSE] Purpose of Key5
SECURE_BOOT_EN, EFUSE_BLK0, 116, 1, [] Set this bit to enable secure boot
SECURE_BOOT_AGGRESSIVE_REVOKE, EFUSE_BLK0, 117, 1, [] Set this bit to enable revoking aggressive secure boot
FLASH_TPUW, EFUSE_BLK0, 124, 4, [] Configures flash waiting time after power-up; in unit of ms. If the value is less than 15; the waiting time is the configurable value; Otherwise; the waiting time is twice the configurable value
DIS_DOWNLOAD_MODE, EFUSE_BLK0, 128, 1, [] Set this bit to disable download mode (boot_mode[3:0] = 0; 1; 2; 3; 6; 7)
DIS_DIRECT_BOOT, EFUSE_BLK0, 129, 1, [DIS_LEGACY_SPI_BOOT] Disable direct boot mode
ENABLE_SECURITY_DOWNLOAD, EFUSE_BLK0, 133, 1, [] Set this bit to enable secure UART download mode
UART_PRINT_CONTROL, EFUSE_BLK0, 134, 2, [] Set the default UARTboot message output mode {0: "Enable"; 1: "Enable when GPIO8 is low at reset"; 2: "Enable when GPIO8 is high at reset"; 3: "Disable"}
FORCE_SEND_RESUME, EFUSE_BLK0, 141, 1, [] Set this bit to force ROM code to send a resume command during SPI boot
SECURE_VERSION, EFUSE_BLK0, 142, 16, [] Secure version (used by ESP-IDF anti-rollback feature)
ERR_RST_ENABLE, EFUSE_BLK0, 159, 1, [] Use BLOCK0 to check error record registers {0: "without check"; 1: "with check"}
DISABLE_WAFER_VERSION_MAJOR, EFUSE_BLK0, 160, 1, [] Disables check of wafer version major
DISABLE_BLK_VERSION_MAJOR, EFUSE_BLK0, 161, 1, [] Disables check of blk version major
MAC, EFUSE_BLK1, 40, 8, [MAC_FACTORY] MAC address
, EFUSE_BLK1, 32, 8, [MAC_FACTORY] MAC address
, EFUSE_BLK1, 24, 8, [MAC_FACTORY] MAC address
, EFUSE_BLK1, 16, 8, [MAC_FACTORY] MAC address
, EFUSE_BLK1, 8, 8, [MAC_FACTORY] MAC address
, EFUSE_BLK1, 0, 8, [MAC_FACTORY] MAC address
SPI_PAD_CONFIG_CLK, EFUSE_BLK1, 48, 6, [] SPI PAD CLK
SPI_PAD_CONFIG_Q, EFUSE_BLK1, 54, 6, [] SPI PAD Q(D1)
SPI_PAD_CONFIG_D, EFUSE_BLK1, 60, 6, [] SPI PAD D(D0)
SPI_PAD_CONFIG_CS, EFUSE_BLK1, 66, 6, [] SPI PAD CS
SPI_PAD_CONFIG_HD, EFUSE_BLK1, 72, 6, [] SPI PAD HD(D3)
SPI_PAD_CONFIG_WP, EFUSE_BLK1, 78, 6, [] SPI PAD WP(D2)
SPI_PAD_CONFIG_DQS, EFUSE_BLK1, 84, 6, [] SPI PAD DQS
SPI_PAD_CONFIG_D4, EFUSE_BLK1, 90, 6, [] SPI PAD D4
SPI_PAD_CONFIG_D5, EFUSE_BLK1, 96, 6, [] SPI PAD D5
SPI_PAD_CONFIG_D6, EFUSE_BLK1, 102, 6, [] SPI PAD D6
SPI_PAD_CONFIG_D7, EFUSE_BLK1, 108, 6, [] SPI PAD D7
WAFER_VERSION_MINOR_LO, EFUSE_BLK1, 114, 3, [] WAFER_VERSION_MINOR least significant bits
PKG_VERSION, EFUSE_BLK1, 117, 3, [] Package version
