kopia lustrzana https://github.com/espressif/esp-idf
93 wiersze
4.0 KiB
Markdown
93 wiersze
4.0 KiB
Markdown
|
| Supported Targets | ESP32-S2 | ESP32-C3 | ESP32-S3 |
|
||
|
|
| ----------------- | -------- | -------- | -------- |
|
||
|
|
|
||
|
|
# RMT Transmit Loop Example -- Step Motor controller
|
||
|
|
|
||
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
||
|
|
|
||
|
|
RMT peripheral can send customized RMT items in a loop, which means we can use it to generate a configurable length of periodic signal, with accurate number of pulses.
|
||
|
|
|
||
|
|
This example will show how to control an A4988 based step motor driver to step accurately with simple APIs, based on the RMT loop feature. The example also implements a [Smoothstep](https://en.wikipedia.org/wiki/Smoothstep) feature which works out of the box.
|
||
|
|
|
||
|
|
## How to Use Example
|
||
|
|
|
||
|
|
### Hardware Required
|
||
|
|
|
||
|
|
* Recommend running this example on development board with SOC chip that support loop auto-stop feature by hardware (e.g. ESP32-S3)
|
||
|
|
* A USB cable for Power supply and programming
|
||
|
|
* A 4-wire (A+, A-, B+, B-) step motor
|
||
|
|
* An A4988 module
|
||
|
|
|
||
|
|
Connection :
|
||
|
|
|
||
|
|
```
|
||
|
|
+----------------+ +--------------------+ +--------------+
|
||
|
|
| | | A4988 | | 4-wire |
|
||
|
|
| GND +-------------+ GND | | Step |
|
||
|
|
| | | | | Motor |
|
||
|
|
| 5V +-------------+ VDD 1B +------+ A2 |
|
||
|
|
| | | | | |
|
||
|
|
| GPIO18 +------------>+ DIRECTION 1A +------+ A1 |
|
||
|
|
| | | | | |
|
||
|
|
| ESP GPIO17 +------------>+ STEP 2A +------+ B1 |
|
||
|
|
| | | | | |
|
||
|
|
| GPIO16 +------------>+ SLEEP 2B +------+ B2 |
|
||
|
|
| | | | +--------------+
|
||
|
|
| GPIO15 +------------>+ RESET VMOT +-------------------+
|
||
|
|
| | | | |
|
||
|
|
| GPIO7 +------------>+ MS3 GND +----------+ |
|
||
|
|
| | | | | |
|
||
|
|
| GPIO6 +------------>+ MS2 | | |
|
||
|
|
| | | | | |
|
||
|
|
| GPIO5 +------------>+ MS1 | +---+--------+-----+
|
||
|
|
| | | | | GND +12V |
|
||
|
|
| GPIO4 +------------>+ ENABLE | | POWER SUPPLY |
|
||
|
|
+----------------+ +--------------------+ +------------------+
|
||
|
|
|
||
|
|
```
|
||
|
|
|
||
|
|
IO mapping on ESP side can be changed in `step_motor_main.c`:
|
||
|
|
|
||
|
|
```c
|
||
|
|
// GPIO configuration
|
||
|
|
#define STEP_MOTOR_DIRECTION_PIN GPIO_NUM_18
|
||
|
|
#define STEP_MOTOR_STEP_PIN GPIO_NUM_17
|
||
|
|
#define STEP_MOTOR_SLEEP_PIN GPIO_NUM_16
|
||
|
|
#define STEP_MOTOR_RESET_PIN GPIO_NUM_15
|
||
|
|
#define STEP_MOTOR_MS3_PIN GPIO_NUM_7
|
||
|
|
#define STEP_MOTOR_MS2_PIN GPIO_NUM_6
|
||
|
|
#define STEP_MOTOR_MS1_PIN GPIO_NUM_5
|
||
|
|
#define STEP_MOTOR_ENABLE_PIN GPIO_NUM_4
|
||
|
|
```
|
||
|
|
|
||
|
|
### Build and Flash
|
||
|
|
|
||
|
|
Run `idf.py -p PORT flash monitor` to build, flash and monitor the project.
|
||
|
|
|
||
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
||
|
|
|
||
|
|
See the [Getting Started Guide](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/index.html) for full steps to configure and use ESP-IDF to build projects.
|
||
|
|
|
||
|
|
|
||
|
|
## Example Output
|
||
|
|
|
||
|
|
```
|
||
|
|
I (344) step_motor: init
|
||
|
|
I (344) step_motor: set_step
|
||
|
|
I (1354) step_motor: step 10 @ 1000/s
|
||
|
|
I (2364) step_motor: step 100 @ 1000/s
|
||
|
|
I (3464) step_motor: step 1000 @ 1200/s
|
||
|
|
I (5294) step_motor: step 5000 @ 1400/s
|
||
|
|
I (9864) step_motor: smoothstep start 5000 steps @ 500~1400/s
|
||
|
|
I (14454) step_motor: smoothstep finish
|
||
|
|
I (15454) step_motor: continuous running for 5s
|
||
|
|
I (20454) step_motor: stop
|
||
|
|
I (21504) step_motor: deinit
|
||
|
|
```
|
||
|
|
|
||
|
|
Motor should move as output indicates.
|
||
|
|
|
||
|
|
## Troubleshooting
|
||
|
|
|
||
|
|
For any technical queries, please open an [issue] (https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you soon.
|