esp-idf/components/hal/esp32s2/adc_hal.c

124 wiersze
4.3 KiB
C
Czysty Zwykły widok Historia

// Copyright 2015-2019 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// The HAL layer for ADC (ESP32-S2 specific part)
#include "sdkconfig.h"
#include "hal/adc_hal.h"
#include "hal/adc_types.h"
#include "hal/adc_hal_conf.h"
/*---------------------------------------------------------------
Digital controller setting
---------------------------------------------------------------*/
void adc_hal_digi_deinit(void)
{
adc_ll_digi_trigger_disable(); // boss
adc_ll_digi_dma_disable();
adc_ll_digi_clear_pattern_table(ADC_NUM_1);
adc_ll_digi_clear_pattern_table(ADC_NUM_2);
adc_ll_digi_filter_reset(ADC_NUM_1);
adc_ll_digi_filter_reset(ADC_NUM_2);
adc_ll_digi_reset();
adc_ll_digi_controller_clk_disable();
}
void adc_hal_digi_controller_config(const adc_digi_config_t *cfg)
{
/* Single channel mode or multi channel mode. */
adc_ll_digi_set_convert_mode(cfg->conv_mode);
if (cfg->conv_mode & ADC_CONV_SINGLE_UNIT_1) {
if (cfg->adc1_pattern_len) {
adc_ll_digi_clear_pattern_table(ADC_NUM_1);
adc_ll_digi_set_pattern_table_len(ADC_NUM_1, cfg->adc1_pattern_len);
2020-11-17 04:48:35 +00:00
for (uint32_t i = 0; i < cfg->adc1_pattern_len; i++) {
adc_ll_digi_set_pattern_table(ADC_NUM_1, i, cfg->adc1_pattern[i]);
}
}
}
if (cfg->conv_mode & ADC_CONV_SINGLE_UNIT_2) {
if (cfg->adc2_pattern_len) {
adc_ll_digi_clear_pattern_table(ADC_NUM_2);
adc_ll_digi_set_pattern_table_len(ADC_NUM_2, cfg->adc2_pattern_len);
2020-11-17 04:48:35 +00:00
for (uint32_t i = 0; i < cfg->adc2_pattern_len; i++) {
adc_ll_digi_set_pattern_table(ADC_NUM_2, i, cfg->adc2_pattern[i]);
}
}
}
if (cfg->conv_mode & ADC_CONV_SINGLE_UNIT_1) {
adc_ll_set_controller(ADC_NUM_1, ADC_CTRL_DIG);
}
if (cfg->conv_mode & ADC_CONV_SINGLE_UNIT_2) {
adc_ll_set_controller(ADC_NUM_2, ADC_CTRL_DIG);
}
adc_ll_digi_set_output_format(cfg->format);
if (cfg->conv_limit_en) {
adc_ll_digi_set_convert_limit_num(cfg->conv_limit_num);
adc_ll_digi_convert_limit_enable();
} else {
adc_ll_digi_convert_limit_disable();
}
adc_ll_digi_set_trigger_interval(cfg->interval);
adc_hal_digi_clk_config(&cfg->dig_clk);
adc_ll_digi_dma_set_eof_num(cfg->dma_eof_num);
}
/**
* Set ADC digital controller clock division factor. The clock divided from `APLL` or `APB` clock.
* Enable clock and select clock source for ADC digital controller.
* Expression: controller_clk = (`APLL` or `APB`) / (div_num + div_a / div_b + 1).
*
* @note ADC and DAC digital controller share the same frequency divider.
* Please set a reasonable frequency division factor to meet the sampling frequency of the ADC and the output frequency of the DAC.
*
* @param clk Refer to ``adc_digi_clk_t``.
*/
void adc_hal_digi_clk_config(const adc_digi_clk_t *clk)
{
adc_ll_digi_controller_clk_div(clk->div_num, clk->div_b, clk->div_a);
adc_ll_digi_controller_clk_enable(clk->use_apll);
}
/**
* Enable digital controller to trigger the measurement.
*/
void adc_hal_digi_enable(void)
{
adc_ll_digi_dma_enable();
adc_ll_digi_trigger_enable();
}
/**
* Disable digital controller to trigger the measurement.
*/
void adc_hal_digi_disable(void)
{
adc_ll_digi_trigger_disable();
adc_ll_digi_dma_disable();
}
/**
* Config monitor of adc digital controller.
*
* @note The monitor will monitor all the enabled channel data of the each ADC unit at the same time.
* @param adc_n ADC unit.
* @param config Refer to ``adc_digi_monitor_t``.
*/
void adc_hal_digi_monitor_config(adc_ll_num_t adc_n, adc_digi_monitor_t *config)
{
adc_ll_digi_monitor_set_mode(adc_n, config->mode);
adc_ll_digi_monitor_set_thres(adc_n, config->threshold);
}