kopia lustrzana https://github.com/Aircoookie/WLED
112 wiersze
3.5 KiB
C++
112 wiersze
3.5 KiB
C++
/*
|
|
* This file allows you to add own functionality to WLED more easily
|
|
* See: https://github.com/Aircoookie/WLED/wiki/Add-own-functionality
|
|
* EEPROM bytes 2750+ are reserved for your custom use case. (if you extend #define EEPSIZE in wled_eeprom.h)
|
|
* bytes 2400+ are currently ununsed, but might be used for future wled features
|
|
*/
|
|
|
|
//Use userVar0 and userVar1 (API calls &U0=,&U1=, uint16_t)
|
|
|
|
byte wipeState = 0; //0: inactive 1: wiping 2: solid
|
|
unsigned long timeStaticStart = 0;
|
|
uint16_t previousUserVar0 = 0;
|
|
|
|
//comment this out if you want the turn off effect to be just fading out instead of reverse wipe
|
|
#define STAIRCASE_WIPE_OFF
|
|
|
|
//gets called once at boot. Do all initialization that doesn't depend on network here
|
|
void userSetup()
|
|
{
|
|
//setup PIR sensor here, if needed
|
|
}
|
|
|
|
//gets called every time WiFi is (re-)connected. Initialize own network interfaces here
|
|
void userConnected()
|
|
{
|
|
|
|
}
|
|
|
|
//loop. You can use "if (WLED_CONNECTED)" to check for successful connection
|
|
void userLoop()
|
|
{
|
|
//userVar0 (U0 in HTTP API):
|
|
//has to be set to 1 if movement is detected on the PIR that is the same side of the staircase as the ESP8266
|
|
//has to be set to 2 if movement is detected on the PIR that is the opposite side
|
|
//can be set to 0 if no movement is detected. Otherwise LEDs will turn off after a configurable timeout (userVar1 seconds)
|
|
|
|
if (userVar0 > 0)
|
|
{
|
|
if ((previousUserVar0 == 1 && userVar0 == 2) || (previousUserVar0 == 2 && userVar0 == 1)) wipeState = 3; //turn off if other PIR triggered
|
|
previousUserVar0 = userVar0;
|
|
|
|
if (wipeState == 0) {
|
|
startWipe();
|
|
wipeState = 1;
|
|
} else if (wipeState == 1) { //wiping
|
|
uint32_t cycleTime = 360 + (255 - effectSpeed)*75; //this is how long one wipe takes (minus 25 ms to make sure we switch in time)
|
|
if (millis() + strip.timebase > (cycleTime - 25)) { //wipe complete
|
|
effectCurrent = FX_MODE_STATIC;
|
|
timeStaticStart = millis();
|
|
colorUpdated(CALL_MODE_NOTIFICATION);
|
|
wipeState = 2;
|
|
}
|
|
} else if (wipeState == 2) { //static
|
|
if (userVar1 > 0) //if U1 is not set, the light will stay on until second PIR or external command is triggered
|
|
{
|
|
if (millis() - timeStaticStart > userVar1*1000) wipeState = 3;
|
|
}
|
|
} else if (wipeState == 3) { //switch to wipe off
|
|
#ifdef STAIRCASE_WIPE_OFF
|
|
effectCurrent = FX_MODE_COLOR_WIPE;
|
|
strip.timebase = 360 + (255 - effectSpeed)*75 - millis(); //make sure wipe starts fully lit
|
|
colorUpdated(CALL_MODE_NOTIFICATION);
|
|
wipeState = 4;
|
|
#else
|
|
turnOff();
|
|
#endif
|
|
} else { //wiping off
|
|
if (millis() + strip.timebase > (725 + (255 - effectSpeed)*150)) turnOff(); //wipe complete
|
|
}
|
|
} else {
|
|
wipeState = 0; //reset for next time
|
|
if (previousUserVar0) {
|
|
#ifdef STAIRCASE_WIPE_OFF
|
|
userVar0 = previousUserVar0;
|
|
wipeState = 3;
|
|
#else
|
|
turnOff();
|
|
#endif
|
|
}
|
|
previousUserVar0 = 0;
|
|
}
|
|
}
|
|
|
|
void startWipe()
|
|
{
|
|
bri = briLast; //turn on
|
|
transitionDelayTemp = 0; //no transition
|
|
effectCurrent = FX_MODE_COLOR_WIPE;
|
|
resetTimebase(); //make sure wipe starts from beginning
|
|
|
|
//set wipe direction
|
|
Segment& seg = strip.getSegment(0);
|
|
bool doReverse = (userVar0 == 2);
|
|
seg.setOption(1, doReverse);
|
|
|
|
colorUpdated(CALL_MODE_NOTIFICATION);
|
|
}
|
|
|
|
void turnOff()
|
|
{
|
|
#ifdef STAIRCASE_WIPE_OFF
|
|
transitionDelayTemp = 0; //turn off immediately after wipe completed
|
|
#else
|
|
transitionDelayTemp = 4000; //fade out slowly
|
|
#endif
|
|
bri = 0;
|
|
stateUpdated(CALL_MODE_NOTIFICATION);
|
|
wipeState = 0;
|
|
userVar0 = 0;
|
|
previousUserVar0 = 0;
|
|
}
|