#pragma once

#include "wled.h"

//
// Inspired by the original v2 usermods
// * usermod_v2_rotary_encoder_ui
//
// v2 usermod that provides a rotary encoder-based UI.
//
// This usermod allows you to control:
// 
// * Brightness
// * Selected Effect
// * Effect Speed
// * Effect Intensity
// * Palette
//
// Change between modes by pressing a button.
//
// Dependencies
// * This Usermod works best coupled with 
//   FourLineDisplayUsermod.
//
// If FourLineDisplayUsermod is used the folowing options are also enabled
//
// * main color
// * saturation of main color
// * display network (long press buttion)
//

#ifdef USERMOD_MODE_SORT
  #error "Usermod Mode Sort is no longer required. Remove -D USERMOD_MODE_SORT from platformio.ini"
#endif

#ifndef ENCODER_DT_PIN
#define ENCODER_DT_PIN 18
#endif

#ifndef ENCODER_CLK_PIN
#define ENCODER_CLK_PIN 5
#endif

#ifndef ENCODER_SW_PIN
#define ENCODER_SW_PIN 19
#endif

#ifndef ENCODER_MAX_DELAY_MS    // max delay between polling encoder pins
#define ENCODER_MAX_DELAY_MS 8  // 8 milliseconds => max 120 change impulses in 1 second, for full turn of a 30/30 encoder (4 changes per segment, 30 segments for one turn)
#endif

#ifndef USERMOD_USE_PCF8574
  #undef USE_PCF8574
  #define USE_PCF8574 false
#else
  #undef USE_PCF8574
  #define USE_PCF8574 true
#endif

#ifndef PCF8574_ADDRESS
  #define PCF8574_ADDRESS 0x20  // some may start at 0x38
#endif

#ifndef PCF8574_INT_PIN
  #define PCF8574_INT_PIN -1    // GPIO connected to INT pin on PCF8574
#endif

// The last UI state, remove color and saturation option if display not active (too many options)
#ifdef USERMOD_FOUR_LINE_DISPLAY
 #define LAST_UI_STATE 11
#else
 #define LAST_UI_STATE 4
#endif

// Number of modes at the start of the list to not sort
#define MODE_SORT_SKIP_COUNT 1

// Which list is being sorted
static const char **listBeingSorted;

/**
 * Modes and palettes are stored as strings that
 * end in a quote character. Compare two of them.
 * We are comparing directly within either
 * JSON_mode_names or JSON_palette_names.
 */
static int re_qstringCmp(const void *ap, const void *bp) {
  const char *a = listBeingSorted[*((byte *)ap)];
  const char *b = listBeingSorted[*((byte *)bp)];
  int i = 0;
  do {
    char aVal = pgm_read_byte_near(a + i);
    if (aVal >= 97 && aVal <= 122) {
      // Lowercase
      aVal -= 32;
    }
    char bVal = pgm_read_byte_near(b + i);
    if (bVal >= 97 && bVal <= 122) {
      // Lowercase
      bVal -= 32;
    }
    // Really we shouldn't ever get to '\0'
    if (aVal == '"' || bVal == '"' || aVal == '\0' || bVal == '\0') {
      // We're done. one is a substring of the other
      // or something happenend and the quote didn't stop us.
      if (aVal == bVal) {
        // Same value, probably shouldn't happen
        // with this dataset
        return 0;
      }
      else if (aVal == '"' || aVal == '\0') {
        return -1;
      }
      else {
        return 1;
      }
    }
    if (aVal == bVal) {
      // Same characters. Move to the next.
      i++;
      continue;
    }
    // We're done
    if (aVal < bVal) {
      return -1;
    }
    else {
      return 1;
    }
  } while (true);
  // We shouldn't get here.
  return 0;
}


static volatile uint8_t pcfPortData = 0;                // port expander port state
static volatile uint8_t addrPcf8574 = PCF8574_ADDRESS;  // has to be accessible in ISR

// Interrupt routine to read I2C rotary state
// if we are to use PCF8574 port expander we will need to rely on interrupts as polling I2C every 2ms
// is a waste of resources and causes 4LD to fail.
// in such case rely on ISR to read pin values and store them into static variable
static void IRAM_ATTR i2cReadingISR() {
  Wire.requestFrom(addrPcf8574, 1U);
  if (Wire.available()) {
    pcfPortData = Wire.read();
  }
}


class RotaryEncoderUIUsermod : public Usermod {

  private:

    const int8_t fadeAmount;    // Amount to change every step (brightness)
    unsigned long loopTime;

    unsigned long buttonPressedTime;
    unsigned long buttonWaitTime;
    bool buttonPressedBefore;
    bool buttonLongPressed;

    int8_t pinA;                // DT from encoder
    int8_t pinB;                // CLK from encoder
    int8_t pinC;                // SW from encoder

    unsigned char select_state; // 0: brightness, 1: effect, 2: effect speed, ...

    uint16_t currentHue1;       // default boot color
    byte currentSat1;
    uint8_t currentCCT;
    
  #ifdef USERMOD_FOUR_LINE_DISPLAY
    FourLineDisplayUsermod *display;
  #else
    void* display;
  #endif

    // Pointers the start of the mode names within JSON_mode_names
    const char **modes_qstrings;

    // Array of mode indexes in alphabetical order.
    byte *modes_alpha_indexes;

    // Pointers the start of the palette names within JSON_palette_names
    const char **palettes_qstrings;

    // Array of palette indexes in alphabetical order.
    byte *palettes_alpha_indexes;

    struct { // reduce memory footprint
      bool Enc_A      : 1;
      bool Enc_B      : 1;
      bool Enc_A_prev : 1;
    };

    bool currentEffectAndPaletteInitialized;
    uint8_t effectCurrentIndex;
    uint8_t effectPaletteIndex;
    uint8_t knownMode;
    uint8_t knownPalette;

    byte presetHigh;
    byte presetLow;

    bool applyToAll;

    bool initDone;
    bool enabled;

    bool usePcf8574;
    int8_t pinIRQ;

    // strings to reduce flash memory usage (used more than twice)
    static const char _name[];
    static const char _enabled[];
    static const char _DT_pin[];
    static const char _CLK_pin[];
    static const char _SW_pin[];
    static const char _presetHigh[];
    static const char _presetLow[];
    static const char _applyToAll[];
    static const char _pcf8574[];
    static const char _pcfAddress[];
    static const char _pcfINTpin[];

    /**
     * readPin() - read rotary encoder pin value
     */
    byte readPin(uint8_t pin);

    /**
     * Sort the modes and palettes to the index arrays
     * modes_alpha_indexes and palettes_alpha_indexes.
     */
    void sortModesAndPalettes();
    byte *re_initIndexArray(int numModes);

    /**
     * Return an array of mode or palette names from the JSON string.
     * They don't end in '\0', they end in '"'. 
     */
    const char **re_findModeStrings(const char json[], int numModes);

    /**
     * Sort either the modes or the palettes using quicksort.
     */
    void re_sortModes(const char **modeNames, byte *indexes, int count, int numSkip);

  public:

    RotaryEncoderUIUsermod()
      : fadeAmount(5)
      , buttonPressedTime(0)
      , buttonWaitTime(0)
      , buttonPressedBefore(false)
      , buttonLongPressed(false)
      , pinA(ENCODER_DT_PIN)
      , pinB(ENCODER_CLK_PIN)
      , pinC(ENCODER_SW_PIN)
      , select_state(0)
      , currentHue1(16)
      , currentSat1(255)
      , currentCCT(128)
      , display(nullptr)
      , modes_qstrings(nullptr)
      , modes_alpha_indexes(nullptr)
      , palettes_qstrings(nullptr)
      , palettes_alpha_indexes(nullptr)
      , currentEffectAndPaletteInitialized(false)
      , effectCurrentIndex(0)
      , effectPaletteIndex(0)
      , knownMode(0)
      , knownPalette(0)
      , presetHigh(0)
      , presetLow(0)
      , applyToAll(true)
      , initDone(false)
      , enabled(true)
      , usePcf8574(USE_PCF8574)
      , pinIRQ(PCF8574_INT_PIN)
    {}

    /*
     * getId() allows you to optionally give your V2 usermod an unique ID (please define it in const.h!).
     * This could be used in the future for the system to determine whether your usermod is installed.
     */
    uint16_t getId() override { return USERMOD_ID_ROTARY_ENC_UI; }
    /**
     * Enable/Disable the usermod
     */
    inline void enable(bool enable) { if (!(pinA<0 || pinB<0 || pinC<0)) enabled = enable; }

    /**
     * Get usermod enabled/disabled state
     */
    inline bool isEnabled() { return enabled; }

    /**
     * setup() is called once at boot. WiFi is not yet connected at this point.
     * You can use it to initialize variables, sensors or similar.
     */
    void setup() override;

    /**
     * connected() is called every time the WiFi is (re)connected
     * Use it to initialize network interfaces
     */
    //void connected();

    /**
     * loop() is called continuously. Here you can check for events, read sensors, etc.
     */
    void loop() override;

#ifndef WLED_DISABLE_MQTT
    //bool onMqttMessage(char* topic, char* payload) override;
    //void onMqttConnect(bool sessionPresent) override;
#endif

    /**
     * handleButton() can be used to override default button behaviour. Returning true
     * will prevent button working in a default way.
     * Replicating button.cpp
     */
    //bool handleButton(uint8_t b) override;

    /**
     * addToJsonInfo() can be used to add custom entries to the /json/info part of the JSON API.
     */
    //void addToJsonInfo(JsonObject &root) override;

    /**
     * addToJsonState() can be used to add custom entries to the /json/state part of the JSON API (state object).
     * Values in the state object may be modified by connected clients
     */
    //void addToJsonState(JsonObject &root) override;

    /**
     * readFromJsonState() can be used to receive data clients send to the /json/state part of the JSON API (state object).
     * Values in the state object may be modified by connected clients
     */
    //void readFromJsonState(JsonObject &root) override;

    /**
     * provide the changeable values
     */
    void addToConfig(JsonObject &root) override;

    void appendConfigData() override;

    /**
     * restore the changeable values
     * readFromConfig() is called before setup() to populate properties from values stored in cfg.json
     * 
     * The function should return true if configuration was successfully loaded or false if there was no configuration.
     */
    bool readFromConfig(JsonObject &root) override;

    // custom methods
    void displayNetworkInfo();
    void findCurrentEffectAndPalette();
    bool changeState(const char *stateName, byte markedLine, byte markedCol, byte glyph);
    void lampUdated();
    void changeBrightness(bool increase);
    void changeEffect(bool increase);
    void changeEffectSpeed(bool increase);
    void changeEffectIntensity(bool increase);
    void changeCustom(uint8_t par, bool increase);
    void changePalette(bool increase);
    void changeHue(bool increase);
    void changeSat(bool increase);
    void changePreset(bool increase);
    void changeCCT(bool increase);
};


/**
 * readPin() - read rotary encoder pin value
 */
byte RotaryEncoderUIUsermod::readPin(uint8_t pin) {
  if (usePcf8574) {
    if (pin >= 100) pin -= 100; // PCF I/O ports
    return (pcfPortData>>pin) & 1;
  } else {
    return digitalRead(pin);
  }
}

/**
 * Sort the modes and palettes to the index arrays
 * modes_alpha_indexes and palettes_alpha_indexes.
 */
void RotaryEncoderUIUsermod::sortModesAndPalettes() {
  DEBUG_PRINT(F("Sorting modes: ")); DEBUG_PRINTLN(strip.getModeCount());
  //modes_qstrings = re_findModeStrings(JSON_mode_names, strip.getModeCount());
  modes_qstrings = strip.getModeDataSrc();
  modes_alpha_indexes = re_initIndexArray(strip.getModeCount());
  re_sortModes(modes_qstrings, modes_alpha_indexes, strip.getModeCount(), MODE_SORT_SKIP_COUNT);

  DEBUG_PRINT(F("Sorting palettes: ")); DEBUG_PRINT(strip.getPaletteCount()); DEBUG_PRINT('/'); DEBUG_PRINTLN(strip.customPalettes.size());
  palettes_qstrings = re_findModeStrings(JSON_palette_names, strip.getPaletteCount());
  palettes_alpha_indexes = re_initIndexArray(strip.getPaletteCount());
  if (strip.customPalettes.size()) {
    for (int i=0; i<strip.customPalettes.size(); i++) {
      palettes_alpha_indexes[strip.getPaletteCount()-strip.customPalettes.size()+i] = 255-i;
      palettes_qstrings[strip.getPaletteCount()-strip.customPalettes.size()+i] = PSTR("~Custom~");
    }
  }
  // How many palette names start with '*' and should not be sorted?
  // (Also skipping the first one, 'Default').
  int skipPaletteCount = 1;
  while (pgm_read_byte_near(palettes_qstrings[skipPaletteCount]) == '*') skipPaletteCount++;
  re_sortModes(palettes_qstrings, palettes_alpha_indexes, strip.getPaletteCount()-strip.customPalettes.size(), skipPaletteCount);
}

byte *RotaryEncoderUIUsermod::re_initIndexArray(int numModes) {
  byte *indexes = (byte *)malloc(sizeof(byte) * numModes);
  for (byte i = 0; i < numModes; i++) {
    indexes[i] = i;
  }
  return indexes;
}

/**
 * Return an array of mode or palette names from the JSON string.
 * They don't end in '\0', they end in '"'. 
 */
const char **RotaryEncoderUIUsermod::re_findModeStrings(const char json[], int numModes) {
  const char **modeStrings = (const char **)malloc(sizeof(const char *) * numModes);
  uint8_t modeIndex = 0;
  bool insideQuotes = false;
  // advance past the mark for markLineNum that may exist.
  char singleJsonSymbol;

  // Find the mode name in JSON
  bool complete = false;
  for (size_t i = 0; i < strlen_P(json); i++) {
    singleJsonSymbol = pgm_read_byte_near(json + i);
    if (singleJsonSymbol == '\0') break;
    switch (singleJsonSymbol) {
      case '"':
        insideQuotes = !insideQuotes;
        if (insideQuotes) {
          // We have a new mode or palette
          modeStrings[modeIndex] = (char *)(json + i + 1);
        }
        break;
      case '[':
        break;
      case ']':
        if (!insideQuotes) complete = true;
        break;
      case ',':
        if (!insideQuotes) modeIndex++;
      default:
        if (!insideQuotes) break;
    }
    if (complete) break;
  }
  return modeStrings;
}

/**
 * Sort either the modes or the palettes using quicksort.
 */
void RotaryEncoderUIUsermod::re_sortModes(const char **modeNames, byte *indexes, int count, int numSkip) {
  if (!modeNames) return;
  listBeingSorted = modeNames;
  qsort(indexes + numSkip, count - numSkip, sizeof(byte), re_qstringCmp);
  listBeingSorted = nullptr;
}


// public methods


/*
  * setup() is called once at boot. WiFi is not yet connected at this point.
  * You can use it to initialize variables, sensors or similar.
  */
void RotaryEncoderUIUsermod::setup()
{
  DEBUG_PRINTLN(F("Usermod Rotary Encoder init."));

  if (usePcf8574) {
    if (i2c_sda < 0 || i2c_scl < 0 || pinA < 0 || pinB < 0 || pinC < 0) {
      DEBUG_PRINTLN(F("I2C and/or PCF8574 pins unused, disabling."));
      enabled = false;
      return;
    } else {
      if (pinIRQ >= 0 && pinManager.allocatePin(pinIRQ, false, PinOwner::UM_RotaryEncoderUI)) {
        pinMode(pinIRQ, INPUT_PULLUP);
        attachInterrupt(pinIRQ, i2cReadingISR, FALLING); // RISING, FALLING, CHANGE, ONLOW, ONHIGH
        DEBUG_PRINTLN(F("Interrupt attached."));
      } else {
        DEBUG_PRINTLN(F("Unable to allocate interrupt pin, disabling."));
        pinIRQ = -1;
        enabled = false;
        return;
      }
    }
  } else {
    PinManagerPinType pins[3] = { { pinA, false }, { pinB, false }, { pinC, false } };
    if (pinA<0 || pinB<0 || !pinManager.allocateMultiplePins(pins, 3, PinOwner::UM_RotaryEncoderUI)) {
      pinA = pinB = pinC = -1;
      enabled = false;
      return;
    }

    #ifndef USERMOD_ROTARY_ENCODER_GPIO
      #define USERMOD_ROTARY_ENCODER_GPIO INPUT_PULLUP
    #endif
    pinMode(pinA, USERMOD_ROTARY_ENCODER_GPIO);
    pinMode(pinB, USERMOD_ROTARY_ENCODER_GPIO);
    if (pinC>=0) pinMode(pinC, USERMOD_ROTARY_ENCODER_GPIO);
  }

  loopTime = millis();

  currentCCT = (approximateKelvinFromRGB(RGBW32(col[0], col[1], col[2], col[3])) - 1900) >> 5;

  if (!initDone) sortModesAndPalettes();

#ifdef USERMOD_FOUR_LINE_DISPLAY
  // This Usermod uses FourLineDisplayUsermod for the best experience.
  // But it's optional. But you want it.
  display = (FourLineDisplayUsermod*) usermods.lookup(USERMOD_ID_FOUR_LINE_DISP);
  if (display != nullptr) {
    display->setMarkLine(1, 0);
  }
#endif

  initDone = true;
  Enc_A = readPin(pinA); // Read encoder pins
  Enc_B = readPin(pinB);
  Enc_A_prev = Enc_A;
}

/*
  * loop() is called continuously. Here you can check for events, read sensors, etc.
  * 
  * Tips:
  * 1. You can use "if (WLED_CONNECTED)" to check for a successful network connection.
  *    Additionally, "if (WLED_MQTT_CONNECTED)" is available to check for a connection to an MQTT broker.
  * 
  * 2. Try to avoid using the delay() function. NEVER use delays longer than 10 milliseconds.
  *    Instead, use a timer check as shown here.
  */
void RotaryEncoderUIUsermod::loop()
{
  if (!enabled) return;
  unsigned long currentTime = millis(); // get the current elapsed time
  if (strip.isUpdating() && ((currentTime - loopTime) < ENCODER_MAX_DELAY_MS)) return;  // be nice, but not too nice

  // Initialize effectCurrentIndex and effectPaletteIndex to
  // current state. We do it here as (at least) effectCurrent
  // is not yet initialized when setup is called.
  
  if (!currentEffectAndPaletteInitialized) {
    findCurrentEffectAndPalette();
  }

  if (modes_alpha_indexes[effectCurrentIndex] != effectCurrent || palettes_alpha_indexes[effectPaletteIndex] != effectPalette) {
    DEBUG_PRINTLN(F("Current mode or palette changed."));
    currentEffectAndPaletteInitialized = false;
  }

  if (currentTime >= (loopTime + 2)) // 2ms since last check of encoder = 500Hz
  {
    bool buttonPressed = !readPin(pinC); //0=pressed, 1=released
    if (buttonPressed) {
      if (!buttonPressedBefore) buttonPressedTime = currentTime;
      buttonPressedBefore = true;
      if (currentTime-buttonPressedTime > 3000) {
        if (!buttonLongPressed) displayNetworkInfo(); //long press for network info
        buttonLongPressed = true;
      }
    } else if (!buttonPressed && buttonPressedBefore) {
      bool doublePress = buttonWaitTime;
      buttonWaitTime = 0;
      if (!buttonLongPressed) {
        if (doublePress) {
          toggleOnOff();
          lampUdated();
        } else {
          buttonWaitTime = currentTime;
        }
      }
      buttonLongPressed = false;
      buttonPressedBefore = false;
    }
    if (buttonWaitTime && currentTime-buttonWaitTime>350 && !buttonPressedBefore) { //same speed as in button.cpp
      buttonWaitTime = 0;
      char newState = select_state + 1;
      bool changedState = false;
      char lineBuffer[64];
      do {
        // find new state
        switch (newState) {
          case  0: strcpy_P(lineBuffer, PSTR("Brightness")); changedState = true; break;
          case  1: if (!extractModeSlider(effectCurrent, 0, lineBuffer, 63)) newState++; else changedState = true; break; // speed
          case  2: if (!extractModeSlider(effectCurrent, 1, lineBuffer, 63)) newState++; else changedState = true; break; // intensity
          case  3: strcpy_P(lineBuffer, PSTR("Color Palette")); changedState = true; break;
          case  4: strcpy_P(lineBuffer, PSTR("Effect")); changedState = true; break;
          case  5: strcpy_P(lineBuffer, PSTR("Main Color")); changedState = true; break;
          case  6: strcpy_P(lineBuffer, PSTR("Saturation")); changedState = true; break;
          case  7: 
            if (!(strip.getSegment(applyToAll ? strip.getFirstSelectedSegId() : strip.getMainSegmentId()).getLightCapabilities() & 0x04)) newState++;
            else { strcpy_P(lineBuffer, PSTR("CCT")); changedState = true; }
            break;
          case  8: if (presetHigh==0 || presetLow == 0) newState++; else { strcpy_P(lineBuffer, PSTR("Preset")); changedState = true; } break;
          case  9:
          case 10:
          case 11: if (!extractModeSlider(effectCurrent, newState-7, lineBuffer, 63)) newState++; else changedState = true; break; // custom
        }
        if (newState > LAST_UI_STATE) newState = 0;
      } while (!changedState);
      if (display != nullptr) {
        switch (newState) {
          case  0: changedState = changeState(lineBuffer,   1,   0,  1); break; //1  = sun
          case  1: changedState = changeState(lineBuffer,   1,   4,  2); break; //2  = skip forward
          case  2: changedState = changeState(lineBuffer,   1,   8,  3); break; //3  = fire
          case  3: changedState = changeState(lineBuffer,   2,   0,  4); break; //4  = custom palette
          case  4: changedState = changeState(lineBuffer,   3,   0,  5); break; //5  = puzzle piece
          case  5: changedState = changeState(lineBuffer, 255, 255,  7); break; //7  = brush
          case  6: changedState = changeState(lineBuffer, 255, 255,  8); break; //8  = contrast
          case  7: changedState = changeState(lineBuffer, 255, 255, 10); break; //10 = star
          case  8: changedState = changeState(lineBuffer, 255, 255, 11); break; //11 = heart
          case  9: changedState = changeState(lineBuffer, 255, 255, 10); break; //10 = star
          case 10: changedState = changeState(lineBuffer, 255, 255, 10); break; //10 = star
          case 11: changedState = changeState(lineBuffer, 255, 255, 10); break; //10 = star
        }
      }
      if (changedState) select_state = newState;
    }

    Enc_A = readPin(pinA); // Read encoder pins
    Enc_B = readPin(pinB);
    if ((Enc_A) && (!Enc_A_prev))
    { // A has gone from high to low
      if (Enc_B == LOW)    //changes to LOW so that then encoder registers a change at the very end of a pulse
      { // B is high so clockwise
        switch(select_state) {
          case  0: changeBrightness(true);      break;
          case  1: changeEffectSpeed(true);     break;
          case  2: changeEffectIntensity(true); break;
          case  3: changePalette(true);         break;
          case  4: changeEffect(true);          break;
          case  5: changeHue(true);             break;
          case  6: changeSat(true);             break;
          case  7: changeCCT(true);             break;
          case  8: changePreset(true);          break;
          case  9: changeCustom(1,true);        break;
          case 10: changeCustom(2,true);        break;
          case 11: changeCustom(3,true);        break;
        }
      }
      else if (Enc_B == HIGH)
      { // B is low so counter-clockwise
        switch(select_state) {
          case  0: changeBrightness(false);      break;
          case  1: changeEffectSpeed(false);     break;
          case  2: changeEffectIntensity(false); break;
          case  3: changePalette(false);         break;
          case  4: changeEffect(false);          break;
          case  5: changeHue(false);             break;
          case  6: changeSat(false);             break;
          case  7: changeCCT(false);             break;
          case  8: changePreset(false);          break;
          case  9: changeCustom(1,false);        break;
          case 10: changeCustom(2,false);        break;
          case 11: changeCustom(3,false);        break;
        }
      }
    }
    Enc_A_prev = Enc_A;     // Store value of A for next time
    loopTime = currentTime; // Updates loopTime
  }
}

void RotaryEncoderUIUsermod::displayNetworkInfo() {
  #ifdef USERMOD_FOUR_LINE_DISPLAY
  display->networkOverlay(PSTR("NETWORK INFO"), 10000);
  #endif
}

void RotaryEncoderUIUsermod::findCurrentEffectAndPalette() {
  DEBUG_PRINTLN(F("Finding current mode and palette."));
  currentEffectAndPaletteInitialized = true;

  effectCurrentIndex = 0;
  for (int i = 0; i < strip.getModeCount(); i++) {
    if (modes_alpha_indexes[i] == effectCurrent) {
      effectCurrentIndex = i;
      DEBUG_PRINTLN(F("Found current mode."));
      break;
    }
  }

  effectPaletteIndex = 0;
  DEBUG_PRINTLN(effectPalette);
  for (uint8_t i = 0; i < strip.getPaletteCount()+strip.customPalettes.size(); i++) {
    if (palettes_alpha_indexes[i] == effectPalette) {
      effectPaletteIndex = i;
      DEBUG_PRINTLN(F("Found palette."));
      break;
    }
  }
}

bool RotaryEncoderUIUsermod::changeState(const char *stateName, byte markedLine, byte markedCol, byte glyph) {
#ifdef USERMOD_FOUR_LINE_DISPLAY
  if (display != nullptr) {
    if (display->wakeDisplay()) {
      // Throw away wake up input
      display->redraw(true);
      return false;
    }
    display->overlay(stateName, 750, glyph);
    display->setMarkLine(markedLine, markedCol);
  }
#endif
  return true;
}

void RotaryEncoderUIUsermod::lampUdated() {
  //call for notifier -> 0: init 1: direct change 2: button 3: notification 4: nightlight 5: other (No notification)
  // 6: fx changed 7: hue 8: preset cycle 9: blynk 10: alexa
  //setValuesFromFirstSelectedSeg(); //to make transition work on main segment (should no longer be required)
  stateUpdated(CALL_MODE_BUTTON);
  updateInterfaces(CALL_MODE_BUTTON);
}

void RotaryEncoderUIUsermod::changeBrightness(bool increase) {
#ifdef USERMOD_FOUR_LINE_DISPLAY
  if (display && display->wakeDisplay()) {
    display->redraw(true);
    // Throw away wake up input
    return;
  }
  display->updateRedrawTime();
#endif
  //bri = max(min((increase ? bri+fadeAmount : bri-fadeAmount), 255), 0);
  if (bri < 40) bri = max(min((increase ? bri+fadeAmount/2 : bri-fadeAmount/2), 255), 0); // slower steps when brightness < 16%
  else bri = max(min((increase ? bri+fadeAmount : bri-fadeAmount), 255), 0);
  lampUdated();
#ifdef USERMOD_FOUR_LINE_DISPLAY
  display->updateBrightness();
#endif
}


void RotaryEncoderUIUsermod::changeEffect(bool increase) {
#ifdef USERMOD_FOUR_LINE_DISPLAY
  if (display && display->wakeDisplay()) {
    display->redraw(true);
    // Throw away wake up input
    return;
  }
  display->updateRedrawTime();
#endif
  effectCurrentIndex = max(min((increase ? effectCurrentIndex+1 : effectCurrentIndex-1), strip.getModeCount()-1), 0);
  effectCurrent = modes_alpha_indexes[effectCurrentIndex];
  stateChanged = true;
  if (applyToAll) {
    for (byte i=0; i<strip.getSegmentsNum(); i++) {
      Segment& seg = strip.getSegment(i);
      if (!seg.isActive()) continue;
      seg.setMode(effectCurrent);
    }
  } else {
    Segment& seg = strip.getSegment(strip.getMainSegmentId());
    seg.setMode(effectCurrent);
  }
  lampUdated();
#ifdef USERMOD_FOUR_LINE_DISPLAY
  display->showCurrentEffectOrPalette(effectCurrent, JSON_mode_names, 3);
#endif
}


void RotaryEncoderUIUsermod::changeEffectSpeed(bool increase) {
#ifdef USERMOD_FOUR_LINE_DISPLAY
  if (display && display->wakeDisplay()) {
    display->redraw(true);
    // Throw away wake up input
    return;
  }
  display->updateRedrawTime();
#endif
  effectSpeed = max(min((increase ? effectSpeed+fadeAmount : effectSpeed-fadeAmount), 255), 0);
  stateChanged = true;
  if (applyToAll) {
    for (byte i=0; i<strip.getSegmentsNum(); i++) {
      Segment& seg = strip.getSegment(i);
      if (!seg.isActive()) continue;
      seg.speed = effectSpeed;
    }
  } else {
    Segment& seg = strip.getSegment(strip.getMainSegmentId());
    seg.speed = effectSpeed;
  }
  lampUdated();
#ifdef USERMOD_FOUR_LINE_DISPLAY
  display->updateSpeed();
#endif
}


void RotaryEncoderUIUsermod::changeEffectIntensity(bool increase) {
#ifdef USERMOD_FOUR_LINE_DISPLAY
  if (display && display->wakeDisplay()) {
    display->redraw(true);
    // Throw away wake up input
    return;
  }
  display->updateRedrawTime();
#endif
  effectIntensity = max(min((increase ? effectIntensity+fadeAmount : effectIntensity-fadeAmount), 255), 0);
  stateChanged = true;
  if (applyToAll) {
    for (byte i=0; i<strip.getSegmentsNum(); i++) {
      Segment& seg = strip.getSegment(i);
      if (!seg.isActive()) continue;
      seg.intensity = effectIntensity;
    }
  } else {
    Segment& seg = strip.getSegment(strip.getMainSegmentId());
    seg.intensity = effectIntensity;
  }
  lampUdated();
#ifdef USERMOD_FOUR_LINE_DISPLAY
  display->updateIntensity();
#endif
}


void RotaryEncoderUIUsermod::changeCustom(uint8_t par, bool increase) {
  uint8_t val = 0;
#ifdef USERMOD_FOUR_LINE_DISPLAY
  if (display && display->wakeDisplay()) {
    display->redraw(true);
    // Throw away wake up input
    return;
  }
  display->updateRedrawTime();
#endif
  stateChanged = true;
  if (applyToAll) {
    uint8_t id = strip.getFirstSelectedSegId();
    Segment& sid = strip.getSegment(id);
    switch (par) {
      case 3:  val = sid.custom3 = max(min((increase ? sid.custom3+fadeAmount : sid.custom3-fadeAmount), 255), 0); break;
      case 2:  val = sid.custom2 = max(min((increase ? sid.custom2+fadeAmount : sid.custom2-fadeAmount), 255), 0); break;
      default: val = sid.custom1 = max(min((increase ? sid.custom1+fadeAmount : sid.custom1-fadeAmount), 255), 0); break;
    }
    for (byte i=0; i<strip.getSegmentsNum(); i++) {
      Segment& seg = strip.getSegment(i);
      if (!seg.isActive() || i == id) continue;
      switch (par) {
        case 3:  seg.custom3 = sid.custom3; break;
        case 2:  seg.custom2 = sid.custom2; break;
        default: seg.custom1 = sid.custom1; break;
      }
    }
  } else {
    Segment& seg = strip.getMainSegment();
    switch (par) {
      case 3:  val = seg.custom3 = max(min((increase ? seg.custom3+fadeAmount : seg.custom3-fadeAmount), 255), 0); break;
      case 2:  val = seg.custom2 = max(min((increase ? seg.custom2+fadeAmount : seg.custom2-fadeAmount), 255), 0); break;
      default: val = seg.custom1 = max(min((increase ? seg.custom1+fadeAmount : seg.custom1-fadeAmount), 255), 0); break;
    }
  }
  lampUdated();
#ifdef USERMOD_FOUR_LINE_DISPLAY
  char lineBuffer[64];
  sprintf(lineBuffer, "%d", val);
  display->overlay(lineBuffer, 500, 10); // use star
#endif
}


void RotaryEncoderUIUsermod::changePalette(bool increase) {
#ifdef USERMOD_FOUR_LINE_DISPLAY
  if (display && display->wakeDisplay()) {
    display->redraw(true);
    // Throw away wake up input
    return;
  }
  display->updateRedrawTime();
#endif
  effectPaletteIndex = max(min((unsigned)(increase ? effectPaletteIndex+1 : effectPaletteIndex-1), strip.getPaletteCount()+strip.customPalettes.size()-1), 0U);
  effectPalette = palettes_alpha_indexes[effectPaletteIndex];
  stateChanged = true;
  if (applyToAll) {
    for (byte i=0; i<strip.getSegmentsNum(); i++) {
      Segment& seg = strip.getSegment(i);
      if (!seg.isActive()) continue;
      seg.setPalette(effectPalette);
    }
  } else {
    Segment& seg = strip.getSegment(strip.getMainSegmentId());
    seg.setPalette(effectPalette);
  }
  lampUdated();
#ifdef USERMOD_FOUR_LINE_DISPLAY
  display->showCurrentEffectOrPalette(effectPalette, JSON_palette_names, 2);
#endif
}


void RotaryEncoderUIUsermod::changeHue(bool increase){
#ifdef USERMOD_FOUR_LINE_DISPLAY
  if (display && display->wakeDisplay()) {
    display->redraw(true);
    // Throw away wake up input
    return;
  }
  display->updateRedrawTime();
#endif
  currentHue1 = max(min((increase ? currentHue1+fadeAmount : currentHue1-fadeAmount), 255), 0);
  colorHStoRGB(currentHue1*256, currentSat1, col);
  stateChanged = true; 
  if (applyToAll) {
    for (byte i=0; i<strip.getSegmentsNum(); i++) {
      Segment& seg = strip.getSegment(i);
      if (!seg.isActive()) continue;
      seg.colors[0] = RGBW32(col[0], col[1], col[2], col[3]);
    }
  } else {
    Segment& seg = strip.getSegment(strip.getMainSegmentId());
    seg.colors[0] = RGBW32(col[0], col[1], col[2], col[3]);
  }
  lampUdated();
#ifdef USERMOD_FOUR_LINE_DISPLAY
  char lineBuffer[64];
  sprintf(lineBuffer, "%d", currentHue1);
  display->overlay(lineBuffer, 500, 7); // use brush
#endif
}

void RotaryEncoderUIUsermod::changeSat(bool increase){
#ifdef USERMOD_FOUR_LINE_DISPLAY
  if (display && display->wakeDisplay()) {
    display->redraw(true);
    // Throw away wake up input
    return;
  }
  display->updateRedrawTime();
#endif
  currentSat1 = max(min((increase ? currentSat1+fadeAmount : currentSat1-fadeAmount), 255), 0);
  colorHStoRGB(currentHue1*256, currentSat1, col);
  if (applyToAll) {
    for (byte i=0; i<strip.getSegmentsNum(); i++) {
      Segment& seg = strip.getSegment(i);
      if (!seg.isActive()) continue;
      seg.colors[0] = RGBW32(col[0], col[1], col[2], col[3]);
    }
  } else {
    Segment& seg = strip.getSegment(strip.getMainSegmentId());
    seg.colors[0] = RGBW32(col[0], col[1], col[2], col[3]);
  }
  lampUdated();
#ifdef USERMOD_FOUR_LINE_DISPLAY
  char lineBuffer[64];
  sprintf(lineBuffer, "%d", currentSat1);
  display->overlay(lineBuffer, 500, 8); // use contrast
#endif
}

void RotaryEncoderUIUsermod::changePreset(bool increase) {
#ifdef USERMOD_FOUR_LINE_DISPLAY
  if (display && display->wakeDisplay()) {
    display->redraw(true);
    // Throw away wake up input
    return;
  }
  display->updateRedrawTime();
#endif
  if (presetHigh && presetLow && presetHigh > presetLow) {
    StaticJsonDocument<64> root;
    char str[64];
    sprintf_P(str, PSTR("%d~%d~%s"), presetLow, presetHigh, increase?"":"-");
    root["ps"] = str;
    deserializeState(root.as<JsonObject>(), CALL_MODE_BUTTON_PRESET);
/*
    String apireq = F("win&PL=~");
    if (!increase) apireq += '-';
    apireq += F("&P1=");
    apireq += presetLow;
    apireq += F("&P2=");
    apireq += presetHigh;
    handleSet(nullptr, apireq, false);
*/
    lampUdated();
  #ifdef USERMOD_FOUR_LINE_DISPLAY
    sprintf(str, "%d", currentPreset);
    display->overlay(str, 500, 11); // use heart
  #endif
  }
}

void RotaryEncoderUIUsermod::changeCCT(bool increase){
#ifdef USERMOD_FOUR_LINE_DISPLAY
  if (display && display->wakeDisplay()) {
    display->redraw(true);
    // Throw away wake up input
    return;
  }
  display->updateRedrawTime();
#endif
  currentCCT = max(min((increase ? currentCCT+fadeAmount : currentCCT-fadeAmount), 255), 0);
//    if (applyToAll) {
    for (byte i=0; i<strip.getSegmentsNum(); i++) {
      Segment& seg = strip.getSegment(i);
      if (!seg.isActive()) continue;
      seg.setCCT(currentCCT);
    }
//    } else {
//      Segment& seg = strip.getSegment(strip.getMainSegmentId());
//      seg.setCCT(currentCCT, strip.getMainSegmentId());
//    }
  lampUdated();
#ifdef USERMOD_FOUR_LINE_DISPLAY
  char lineBuffer[64];
  sprintf(lineBuffer, "%d", currentCCT);
  display->overlay(lineBuffer, 500, 10); // use star
#endif
}

/*
  * addToJsonInfo() can be used to add custom entries to the /json/info part of the JSON API.
  * Creating an "u" object allows you to add custom key/value pairs to the Info section of the WLED web UI.
  * Below it is shown how this could be used for e.g. a light sensor
  */
/*
void RotaryEncoderUIUsermod::addToJsonInfo(JsonObject& root)
{
  int reading = 20;
  //this code adds "u":{"Light":[20," lux"]} to the info object
  JsonObject user = root["u"];
  if (user.isNull()) user = root.createNestedObject("u");
  JsonArray lightArr = user.createNestedArray("Light"); //name
  lightArr.add(reading); //value
  lightArr.add(" lux"); //unit
}
*/

/*
  * addToJsonState() can be used to add custom entries to the /json/state part of the JSON API (state object).
  * Values in the state object may be modified by connected clients
  */
/*
void RotaryEncoderUIUsermod::addToJsonState(JsonObject &root)
{
  //root["user0"] = userVar0;
}
*/

/*
  * readFromJsonState() can be used to receive data clients send to the /json/state part of the JSON API (state object).
  * Values in the state object may be modified by connected clients
  */
/*
void RotaryEncoderUIUsermod::readFromJsonState(JsonObject &root)
{
  //userVar0 = root["user0"] | userVar0; //if "user0" key exists in JSON, update, else keep old value
  //if (root["bri"] == 255) Serial.println(F("Don't burn down your garage!"));
}
*/

/**
 * addToConfig() (called from set.cpp) stores persistent properties to cfg.json
 */
void RotaryEncoderUIUsermod::addToConfig(JsonObject &root) {
  // we add JSON object: {"Rotary-Encoder":{"DT-pin":12,"CLK-pin":14,"SW-pin":13}}
  JsonObject top = root.createNestedObject(FPSTR(_name)); // usermodname
  top[FPSTR(_enabled)] = enabled;
  top[FPSTR(_DT_pin)]  = pinA;
  top[FPSTR(_CLK_pin)] = pinB;
  top[FPSTR(_SW_pin)]  = pinC;
  top[FPSTR(_presetLow)]  = presetLow;
  top[FPSTR(_presetHigh)] = presetHigh;
  top[FPSTR(_applyToAll)] = applyToAll;
  top[FPSTR(_pcf8574)]    = usePcf8574;
  top[FPSTR(_pcfAddress)] = addrPcf8574;
  top[FPSTR(_pcfINTpin)]  = pinIRQ;
  DEBUG_PRINTLN(F("Rotary Encoder config saved."));
}

void RotaryEncoderUIUsermod::appendConfigData() {
  oappend(SET_F("addInfo('Rotary-Encoder:PCF8574-address',1,'<i>(not hex!)</i>');"));
  oappend(SET_F("d.extra.push({'Rotary-Encoder':{pin:[['P0',100],['P1',101],['P2',102],['P3',103],['P4',104],['P5',105],['P6',106],['P7',107]]}});"));
}

/**
 * readFromConfig() is called before setup() to populate properties from values stored in cfg.json
 *
 * The function should return true if configuration was successfully loaded or false if there was no configuration.
 */
bool RotaryEncoderUIUsermod::readFromConfig(JsonObject &root) {
  // we look for JSON object: {"Rotary-Encoder":{"DT-pin":12,"CLK-pin":14,"SW-pin":13}}
  JsonObject top = root[FPSTR(_name)];
  if (top.isNull()) {
    DEBUG_PRINT(FPSTR(_name));
    DEBUG_PRINTLN(F(": No config found. (Using defaults.)"));
    return false;
  }
  int8_t newDTpin  = top[FPSTR(_DT_pin)]  | pinA;
  int8_t newCLKpin = top[FPSTR(_CLK_pin)] | pinB;
  int8_t newSWpin  = top[FPSTR(_SW_pin)]  | pinC;
  int8_t newIRQpin = top[FPSTR(_pcfINTpin)] | pinIRQ;
  bool   oldPcf8574 = usePcf8574;

  presetHigh = top[FPSTR(_presetHigh)] | presetHigh;
  presetLow  = top[FPSTR(_presetLow)]  | presetLow;
  presetHigh = MIN(250,MAX(0,presetHigh));
  presetLow  = MIN(250,MAX(0,presetLow));

  enabled    = top[FPSTR(_enabled)] | enabled;
  applyToAll = top[FPSTR(_applyToAll)] | applyToAll;

  usePcf8574 = top[FPSTR(_pcf8574)] | usePcf8574;
  addrPcf8574 = top[FPSTR(_pcfAddress)] | addrPcf8574;

  DEBUG_PRINT(FPSTR(_name));
  if (!initDone) {
    // first run: reading from cfg.json
    pinA = newDTpin;
    pinB = newCLKpin;
    pinC = newSWpin;
    DEBUG_PRINTLN(F(" config loaded."));
  } else {
    DEBUG_PRINTLN(F(" config (re)loaded."));
    // changing parameters from settings page
    if (pinA!=newDTpin || pinB!=newCLKpin || pinC!=newSWpin || pinIRQ!=newIRQpin) {
      if (oldPcf8574) {
        if (pinIRQ >= 0) {
          detachInterrupt(pinIRQ);
          pinManager.deallocatePin(pinIRQ, PinOwner::UM_RotaryEncoderUI);
          DEBUG_PRINTLN(F("Deallocated old IRQ pin."));
        }
        pinIRQ = newIRQpin<100 ? newIRQpin : -1; // ignore PCF8574 pins
      } else {
        pinManager.deallocatePin(pinA, PinOwner::UM_RotaryEncoderUI);
        pinManager.deallocatePin(pinB, PinOwner::UM_RotaryEncoderUI);
        pinManager.deallocatePin(pinC, PinOwner::UM_RotaryEncoderUI);
        DEBUG_PRINTLN(F("Deallocated old pins."));
      }
      pinA = newDTpin;
      pinB = newCLKpin;
      pinC = newSWpin;
      if (pinA<0 || pinB<0 || pinC<0) {
        enabled = false;
        return true;
      }
      setup();
    }
  }
  // use "return !top["newestParameter"].isNull();" when updating Usermod with new features
  return !top[FPSTR(_pcfINTpin)].isNull();
}


// strings to reduce flash memory usage (used more than twice)
const char RotaryEncoderUIUsermod::_name[]       PROGMEM = "Rotary-Encoder";
const char RotaryEncoderUIUsermod::_enabled[]    PROGMEM = "enabled";
const char RotaryEncoderUIUsermod::_DT_pin[]     PROGMEM = "DT-pin";
const char RotaryEncoderUIUsermod::_CLK_pin[]    PROGMEM = "CLK-pin";
const char RotaryEncoderUIUsermod::_SW_pin[]     PROGMEM = "SW-pin";
const char RotaryEncoderUIUsermod::_presetHigh[] PROGMEM = "preset-high";
const char RotaryEncoderUIUsermod::_presetLow[]  PROGMEM = "preset-low";
const char RotaryEncoderUIUsermod::_applyToAll[] PROGMEM = "apply-2-all-seg";
const char RotaryEncoderUIUsermod::_pcf8574[]    PROGMEM = "use-PCF8574";
const char RotaryEncoderUIUsermod::_pcfAddress[] PROGMEM = "PCF8574-address";
const char RotaryEncoderUIUsermod::_pcfINTpin[]  PROGMEM = "PCF8574-INT-pin";