Move LED_BUILTIN handling to BusManager class

- reduce max panels

wled00/FX.h

@@ -862,7 +862,7 @@ class WS2812FX {  // 96 bytes
       isMatrix;
 
 #ifndef WLED_DISABLE_2D
-    #define WLED_MAX_PANELS 64
+    #define WLED_MAX_PANELS 18
     uint8_t
       panels;
 

wled00/bus_manager.cpp

@@ -270,12 +270,6 @@ bool BusDigital::canShow() {
 
 void BusDigital::setBrightness(uint8_t b) {
   if (_bri == b) return;
-  //Fix for turning off onboard LED breaking bus
-  #ifdef LED_BUILTIN
-  if (_bri == 0) { // && b > 0, covered by guard if above
-    if (_pins[0] == LED_BUILTIN || _pins[1] == LED_BUILTIN) reinit();
-  }
-  #endif
   Bus::setBrightness(b);
   PolyBus::setBrightness(_busPtr, _iType, b);
 }
@@ -707,6 +701,7 @@ int BusManager::add(BusConfig &bc) {
 }
 
 void BusManager::useParallelOutput(void) {
+  _parallelOutputs = 8; // hardcoded since we use NPB I2S x8 methods
   PolyBus::setParallelI2S1Output();
 }
 
@@ -717,9 +712,81 @@ void BusManager::removeAll() {
   while (!canAllShow()) yield();
   for (unsigned i = 0; i < numBusses; i++) delete busses[i];
   numBusses = 0;
+  _parallelOutputs = 1;
   PolyBus::setParallelI2S1Output(false);
 }
 
+#ifdef ESP32_DATA_IDLE_HIGH
+// #2478
+// If enabled, RMT idle level is set to HIGH when off
+// to prevent leakage current when using an N-channel MOSFET to toggle LED power
+void BusManager::esp32RMTInvertIdle() {
+  bool idle_out;
+  unsigned rmt = 0;
+  for (unsigned u = 0; u < numBusses(); u++) {
+    #if defined(CONFIG_IDF_TARGET_ESP32C3)    // 2 RMT, only has 1 I2S but NPB does not support it ATM
+      if (u > 1) return;
+      rmt = u;
+    #elif defined(CONFIG_IDF_TARGET_ESP32S2)  // 4 RMT, only has 1 I2S bus, supported in NPB
+      if (u > 3) return;
+      rmt = u;
+    #elif defined(CONFIG_IDF_TARGET_ESP32S3)  // 4 RMT, has 2 I2S but NPB does not support them ATM
+      if (u > 3) return;
+      rmt = u;
+    #else
+      if (u < _parallelOutputs) continue;
+      if (u >= _parallelOutputs + 8) return; // only 8 RMT channels
+      rmt = u - _parallelOutputs;
+    #endif
+    if (busses[u]->getLength()==0 || !IS_DIGITAL(busses[u]->getType()) || IS_2PIN(busses[u]->getType())) continue;
+    //assumes that bus number to rmt channel mapping stays 1:1
+    rmt_channel_t ch = static_cast<rmt_channel_t>(rmt);
+    rmt_idle_level_t lvl;
+    rmt_get_idle_level(ch, &idle_out, &lvl);
+    if (lvl == RMT_IDLE_LEVEL_HIGH) lvl = RMT_IDLE_LEVEL_LOW;
+    else if (lvl == RMT_IDLE_LEVEL_LOW) lvl = RMT_IDLE_LEVEL_HIGH;
+    else continue;
+    rmt_set_idle_level(ch, idle_out, lvl);
+  }
+}
+#endif
+
+void BusManager::on() {
+  #ifdef ESP8266
+  //Fix for turning off onboard LED breaking bus
+  if (pinManager.getPinOwner(LED_BUILTIN) == PinOwner::BusDigital) {
+    for (unsigned i = 0; i < numBusses; i++) {
+      uint8_t pins[2] = {255,255};
+      if (IS_DIGITAL(busses[i]->getType()) && busses[i]->getPins(pins)) {
+        if (pins[0] == LED_BUILTIN || pins[1] == LED_BUILTIN) {
+          BusDigital *bus = static_cast<BusDigital*>(busses[i]);
+          bus->reinit();
+          break;
+        }
+      }
+    }
+  }
+  #endif
+  #ifdef ESP32_DATA_IDLE_HIGH
+  esp32RMTInvertIdle();
+  #endif
+}
+
+void BusManager::off() {
+  #ifdef ESP8266
+  // turn off built-in LED if strip is turned off
+  // this will break digital bus so will need to be re-initialised on On
+  if (pinManager.getPinOwner(LED_BUILTIN) == PinOwner::BusDigital) {
+    for (unsigned i = 0; i < numBusses; i++) if (busses[i]->isOffRefreshRequired()) return;
+    pinMode(LED_BUILTIN, OUTPUT);
+    digitalWrite(LED_BUILTIN, HIGH);
+  }
+  #endif
+  #ifdef ESP32_DATA_IDLE_HIGH
+  esp32RMTInvertIdle();
+  #endif
+}
+
 void BusManager::show() {
   _milliAmpsUsed = 0;
   for (unsigned i = 0; i < numBusses; i++) {
@@ -799,4 +866,5 @@ uint8_t       BusManager::numBusses = 0;
 Bus*          BusManager::busses[WLED_MAX_BUSSES+WLED_MIN_VIRTUAL_BUSSES];
 ColorOrderMap BusManager::colorOrderMap = {};
 uint16_t      BusManager::_milliAmpsUsed = 0;
-uint16_t      BusManager::_milliAmpsMax = ABL_MILLIAMPS_DEFAULT;
+uint16_t      BusManager::_milliAmpsMax = ABL_MILLIAMPS_DEFAULT;
+uint8_t       BusManager::_parallelOutputs = 1;

wled00/bus_manager.h

@@ -364,6 +364,9 @@ class BusManager {
     //do not call this method from system context (network callback)
     static void removeAll();
 
+    static void on(void);
+    static void off(void);
+
     static void show();
     static bool canAllShow();
     static void setStatusPixel(uint32_t c);
@@ -391,7 +394,11 @@ class BusManager {
     static ColorOrderMap colorOrderMap;
     static uint16_t _milliAmpsUsed;
     static uint16_t _milliAmpsMax;
+    static uint8_t _parallelOutputs;
 
+    #ifdef ESP32_DATA_IDLE_HIGH
+    static void    esp32RMTInvertIdle();
+    #endif
     static uint8_t getNumVirtualBusses() {
       int j = 0;
       for (int i=0; i<numBusses; i++) if (busses[i]->getType() >= TYPE_NET_DDP_RGB && busses[i]->getType() < 96) j++;

wled00/button.cpp

@@ -358,69 +358,35 @@ void handleButton()
   }
 }
 
-// If enabled, RMT idle level is set to HIGH when off
-// to prevent leakage current when using an N-channel MOSFET to toggle LED power
-#ifdef ESP32_DATA_IDLE_HIGH
-void esp32RMTInvertIdle()
-{
-  bool idle_out;
-  for (uint8_t u = 0; u < BusManager::getNumBusses(); u++)
-  {
-    if (u > 7) return; // only 8 RMT channels, TODO: ESP32 variants have less RMT channels
-    Bus *bus = BusManager::getBus(u);
-    if (!bus || bus->getLength()==0 || !IS_DIGITAL(bus->getType()) || IS_2PIN(bus->getType())) continue;
-    //assumes that bus number to rmt channel mapping stays 1:1
-    rmt_channel_t ch = static_cast<rmt_channel_t>(u);
-    rmt_idle_level_t lvl;
-    rmt_get_idle_level(ch, &idle_out, &lvl);
-    if (lvl == RMT_IDLE_LEVEL_HIGH) lvl = RMT_IDLE_LEVEL_LOW;
-    else if (lvl == RMT_IDLE_LEVEL_LOW) lvl = RMT_IDLE_LEVEL_HIGH;
-    else continue;
-    rmt_set_idle_level(ch, idle_out, lvl);
-  }
-}
-#endif
-
+// handleIO() happens *after* handleTransitions() (see wled.cpp) which may change bri/briT but *before* strip.service()
+// where actual LED painting occurrs
+// this is important for relay control and in the event of turning off on-board LED
 void handleIO()
 {
   handleButton();
 
-  //set relay when LEDs turn on
-  if (strip.getBrightness())
-  {
+  // if we want to control on-board LED (ESP8266) or relay we have to do it here as the final show() may not happen until
+  // next loop() cycle
+  if (strip.getBrightness()) {
     lastOnTime = millis();
-    if (offMode)
-    {
-      #ifdef ESP32_DATA_IDLE_HIGH
-      esp32RMTInvertIdle();
-      #endif
+    if (offMode) {
+      BusManager::on();
       if (rlyPin>=0) {
         pinMode(rlyPin, rlyOpenDrain ? OUTPUT_OPEN_DRAIN : OUTPUT);
         digitalWrite(rlyPin, rlyMde);
       }
       offMode = false;
     }
-  } else if (millis() - lastOnTime > 600)
-  {
+  } else if (millis() - lastOnTime > 600 && !strip.needsUpdate()) {
+    // for turning LED or relay off we need to wait until strip no longer needs updates (strip.trigger())
     if (!offMode) {
-      #ifdef ESP8266
-      // turn off built-in LED if strip is turned off
-      // this will break digital bus so will need to be re-initialised on On
-      PinOwner ledPinOwner = pinManager.getPinOwner(LED_BUILTIN);
-      if (!strip.isOffRefreshRequired() && (ledPinOwner == PinOwner::None || ledPinOwner == PinOwner::BusDigital)) {
-        pinMode(LED_BUILTIN, OUTPUT);
-        digitalWrite(LED_BUILTIN, HIGH);
-      }
-      #endif
-      #ifdef ESP32_DATA_IDLE_HIGH
-      esp32RMTInvertIdle();
-      #endif
+      BusManager::off();
       if (rlyPin>=0) {
         pinMode(rlyPin, rlyOpenDrain ? OUTPUT_OPEN_DRAIN : OUTPUT);
         digitalWrite(rlyPin, !rlyMde);
       }
+      offMode = true;
     }
-    offMode = true;
   }
 }
 

wled00/const.h

@@ -192,9 +192,9 @@
 #define CALL_MODE_INIT           0     //no updates on init, can be used to disable updates
 #define CALL_MODE_DIRECT_CHANGE  1
 #define CALL_MODE_BUTTON         2     //default button actions applied to selected segments
-#define CALL_MODE_NOTIFICATION   3
-#define CALL_MODE_NIGHTLIGHT     4
-#define CALL_MODE_NO_NOTIFY      5
+#define CALL_MODE_NOTIFICATION   3     //caused by incoming notification (UDP or DMX preset)
+#define CALL_MODE_NIGHTLIGHT     4     //nightlight progress
+#define CALL_MODE_NO_NOTIFY      5     //change state but do not send notifications (UDP)
 #define CALL_MODE_FX_CHANGED     6     //no longer used
 #define CALL_MODE_HUE            7
 #define CALL_MODE_PRESET_CYCLE   8     //no longer used

wled00/led.cpp

@@ -195,7 +195,7 @@ void handleTransitions()
       applyFinalBri();
       return;
     }
-    if (tper - tperLast < 0.004f) return;
+    if (tper - tperLast < 0.004f) return; // less than 1 bit change (1/255)
     tperLast = tper;
     briT = briOld + ((bri - briOld) * tper);