mirror
/
WLED
kopia lustrzana https://github.com/Aircoookie/WLED
1
0
Forkuj 0
Kod Zgłoszenia Packages Projekty Wydania Wiki Aktywność

improvements for new MCU support (-S3/-S2/-C3) 

- switch off debug messages to USBCDC, if WLED_DEBUG is not set
- ensure that analogread pins are valid - invalid pins cause lots of error messages and finally lead to watchdog reset on some MCUs.
pull/2943/head
Frank 2022-12-10 19:16:02 +01:00
rodzic cafa78c3f3
commit 7ac8f6dd19
3 zmienionych plików z 46 dodań i 16 usunięć
Pokaż statystyki Ściągnij plik aktualizacji Ściągnij plik porównania Expand all files Collapse all files

30
wled00/cfg.cpp
Wyświetl plik

@ -203,14 +203,28 @@ bool deserializeConfig(JsonObject doc, bool fromFS) {
int8_t pin = btn["pin"][0] | -1;
if (pin > -1 && pinManager.allocatePin(pin, false, PinOwner::Button)) {
btnPin[s] = pin;
if (disablePullUp) {
pinMode(btnPin[s], INPUT);
} else {
#ifdef ESP32
pinMode(btnPin[s], buttonType[s]==BTN_TYPE_PUSH_ACT_HIGH ? INPUT_PULLDOWN : INPUT_PULLUP);
#else
pinMode(btnPin[s], INPUT_PULLUP);
#endif
#ifdef ARDUINO_ARCH_ESP32
// ESP32 only: check that analog button pin is a valid ADC gpio
if (((buttonType[s] == BTN_TYPE_ANALOG) || (buttonType[s] == BTN_TYPE_ANALOG_INVERTED)) && (digitalPinToAnalogChannel(btnPin[s]) < 0))
{
// not an ADC analog pin
DEBUG_PRINTF("PIN ALLOC error: GPIO%d for analog button #%d is not an analog pin!\n", btnPin[s], s);
btnPin[s] = -1;
pinManager.deallocatePin(pin,PinOwner::Button);
}
else
#endif
{
if (disablePullUp) {
pinMode(btnPin[s], INPUT);
} else {
#ifdef ESP32
// first check that analog button is valid
pinMode(btnPin[s], buttonType[s]==BTN_TYPE_PUSH_ACT_HIGH ? INPUT_PULLDOWN : INPUT_PULLUP);
#else
pinMode(btnPin[s], INPUT_PULLUP);
#endif
}
}
} else {
btnPin[s] = -1;

29
wled00/set.cpp
Wyświetl plik

@ -169,14 +169,27 @@ void handleSettingsSet(AsyncWebServerRequest *request, byte subPage)
if (pinManager.allocatePin(hw_btn_pin,false,PinOwner::Button)) {
btnPin[i] = hw_btn_pin;
buttonType[i] = request->arg(be).toInt();
if (disablePullUp) {
pinMode(btnPin[i], INPUT);
} else {
#ifdef ESP32
pinMode(btnPin[i], buttonType[i]==BTN_TYPE_PUSH_ACT_HIGH ? INPUT_PULLDOWN : INPUT_PULLUP);
#else
pinMode(btnPin[i], INPUT_PULLUP);
#endif
#ifdef ARDUINO_ARCH_ESP32
// ESP32 only: check that analog button pin is a valid ADC gpio
if (((buttonType[i] == BTN_TYPE_ANALOG) || (buttonType[i] == BTN_TYPE_ANALOG_INVERTED)) && (digitalPinToAnalogChannel(btnPin[i]) < 0))
{
// not an ADC analog pin
DEBUG_PRINTF("PIN ALLOC error: GPIO%d for analog button #%d is not an analog pin!\n", btnPin[i], i);
btnPin[i] = -1;
pinManager.deallocatePin(hw_btn_pin,PinOwner::Button);
}
else
#endif
{
if (disablePullUp) {
pinMode(btnPin[i], INPUT);
} else {
#ifdef ESP32
pinMode(btnPin[i], buttonType[i]==BTN_TYPE_PUSH_ACT_HIGH ? INPUT_PULLDOWN : INPUT_PULLUP);
#else
pinMode(btnPin[i], INPUT_PULLUP);
#endif
}
}
} else {
btnPin[i] = -1;

3
wled00/wled.cpp
Wyświetl plik

@ -272,6 +272,9 @@ void WLED::setup()
#if defined(WLED_DEBUG) && defined(ARDUINO_ARCH_ESP32) && (defined(CONFIG_IDF_TARGET_ESP32S2) || defined(CONFIG_IDF_TARGET_ESP32C3) || ARDUINO_USB_CDC_ON_BOOT)
delay(2500); // allow CDC USB serial to initialise
#endif
#if !defined(WLED_DEBUG) && defined(ARDUINO_ARCH_ESP32) && !defined(WLED_DEBUG_HOST) && ARDUINO_USB_CDC_ON_BOOT
Serial.setDebugOutput(false); // switch off kernel messages when using USBCDC
#endif
DEBUG_PRINTLN();
DEBUG_PRINT(F("---WLED "));
DEBUG_PRINT(versionString);