fixed touch buttons for ESP32 S2 and S3

touch is implemented differently on S2 and S3, these changes make touch buttons work on S2 and S3

wled00/button.cpp

@@ -99,11 +99,21 @@ bool isButtonPressed(uint8_t i)
     case BTN_TYPE_TOUCH:
     case BTN_TYPE_TOUCH_SWITCH:
       #if defined(ARDUINO_ARCH_ESP32) && !defined(CONFIG_IDF_TARGET_ESP32C3)
-      if (digitalPinToTouchChannel(btnPin[i]) >= 0 && touchRead(pin) <= touchThreshold) return true;
+        #ifdef SOC_TOUCH_VERSION_2 //ESP32 S2 and S3 provide a function to check touch state (state is updated in interrupt)
+          if (touchInterruptGetLastStatus(pin))
+          {
+            return true;
+          }
+        #else
+          if (digitalPinToTouchChannel(btnPin[i]) >= 0 && touchRead(pin) <= touchThreshold)
+          {
+                return true;
+          }
+        #endif
       #endif
-      break;
-  }
-  return false;
+     break;
+    }
+    return false;
 }
 
 void handleSwitch(uint8_t b)
@@ -406,3 +416,12 @@ void handleIO()
     offMode = true;
   }
 }
+
+void IRAM_ATTR touchButtonISR()
+{
+  
+#if defined SOC_TOUCH_VERSION_1 //ESP32 original
+  touchInterruptSetThresholdDirection(flase); //todo: need to flip direction, for that proably need to read current state or something.  
+#endif
+  // For S2 and S3: nothing to do, ISR is just used to update registers of HAL driver
+}

wled00/cfg.cpp

@@ -228,6 +228,7 @@ bool deserializeConfig(JsonObject doc, bool fromFS) {
 
   // read multiple button configuration
   JsonObject btn_obj = hw["btn"];
+  CJSON(touchThreshold, btn_obj[F("tt")]);
   bool pull = btn_obj[F("pull")] | (!disablePullUp); // if true, pullup is enabled
   disablePullUp = !pull;
   JsonArray hw_btn_ins = btn_obj["ins"];
@@ -252,8 +253,16 @@ bool deserializeConfig(JsonObject doc, bool fromFS) {
           btnPin[s] = -1;
           pinManager.deallocatePin(pin,PinOwner::Button);
         }
+        //if touch pin, enable the touch interrupt on ESP32 S2 & S3
+        #ifdef SOC_TOUCH_VERSION_2    // ESP32 S2 and S3 have a fucntion to check touch state but need to attach an interrupt to do so
+          else if ((buttonType[s] == BTN_TYPE_TOUCH || buttonType[s] == BTN_TYPE_TOUCH_SWITCH)) 
+          {
+            touchAttachInterrupt(btnPin[s], touchButtonISR, touchThreshold<<2); //threshold on Touch V2 is much higher (TODO: may need shift by 3 if very noisy)
+          }
+        #endif 
+
         else
-      #endif
+        #endif
         {
           if (disablePullUp) {
             pinMode(btnPin[s], INPUT);
@@ -299,7 +308,7 @@ bool deserializeConfig(JsonObject doc, bool fromFS) {
       }
     }
   }
-  CJSON(touchThreshold,btn_obj[F("tt")]);
+
   CJSON(buttonPublishMqtt,btn_obj["mqtt"]);
 
   int hw_ir_pin = hw["ir"]["pin"] | -2; // 4

wled00/fcn_declare.h

@@ -20,6 +20,7 @@ void doublePressAction(uint8_t b=0);
 bool isButtonPressed(uint8_t b=0);
 void handleButton();
 void handleIO();
+void IRAM_ATTR touchButtonISR();
 
 //cfg.cpp
 bool deserializeConfig(JsonObject doc, bool fromFS = false);