From 6f89cddcde7152b84f7afc1831b6a1dee1fc3206 Mon Sep 17 00:00:00 2001 From: lewisxhe Date: Thu, 20 Feb 2025 16:56:20 +0800 Subject: [PATCH] Update README --- README.MD | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/README.MD b/README.MD index f1d6a7e..b9892ee 100644 --- a/README.MD +++ b/README.MD @@ -5,9 +5,10 @@ 1. **Install USB driver**, [CHxxx Series MAC driver](http://www.wch-ic.com/downloads/CH34XSER_MAC_ZIP.html) , [CHxxx Series Windows driver](http://www.wch-ic.com/downloads/CH343SER_ZIP.html),[CP21xx Series driver](https://www.silabs.com/developers/usb-to-uart-bridge-vcp-drivers?tab=downloads) 2. Copy **TFT_eSPI** to the **** directory 3. Open **Arduino IDE,** find **TFT_eSPI** in the file and example, the **T-Display** factory test program is located at **TFT_eSPI -> FactoryTest**, you can also use other sample programs provided by TFT_eSPI -3 In the **Arduino IDE** tool options, select the development board **ESP32 Dev Module**, **select Disable in the PSRAM option**, **select 4MB in the Flash Size option**, Other keep the default -1. Select the corresponding serial port. If you are not sure, please remove all the serial ports, leaving the board in the USB connection state, just select that one -2. Finally, click upload, the right arrow next to the tick +4. In the **Arduino IDE** tool options, select the development board **ESP32 Dev Module**, **select Disable in the PSRAM option**, **select 4MB in the Flash Size option**, Other keep the default +5. Select the corresponding serial port. If you are not sure, please remove all the serial ports, leaving the board in the USB connection state, just select that one +6. Finally, click upload, the right arrow next to the tick +7. Please note that the highest version currently supported by TFT_eSPI is 2.0.14. Compiling with a version higher than 2.0.14 will result in an error. Please pay attention to the selection of esp32 version. `Tools -> Board -> Boards Manage -> Search esp32 -> 2.0.14 -> Install` ------------------------- 1. **安装 USB 驱动**, [CHxxx Series MAC driver](http://www.wch-ic.com/downloads/CH34XSER_MAC_ZIP.html) , [CHxxx Series Windows driver](http://www.wch-ic.com/downloads/CH343SER_ZIP.html), [CP21xx Series driver](https://www.silabs.com/developers/usb-to-uart-bridge-vcp-drivers?tab=downloads) @@ -16,6 +17,7 @@ 4. 在**Arduino IDE** 工具选项中 ， 开发板选择 **ESP32 Dev Module**,**在PSRAM选项中选择Disable**， **Flash Size 选项中选择4MB** ，其它保持默认 5. 选择对应的串行端口，如果不清楚请移除所有串行端口，之保留板子处于USB连接状态，选择那一个即可 6. 最后可点击上传即可，勾号旁边的向右箭头 +7. 请注意，TFT_eSPI 目前支持最高版本为2.0.14 ，高于 2.0.14 编译则会报错，请注意esp32 版本的选择:`Tools -> Board -> Boards Manage ->Search esp32 -> 2.0.14 -> Install` ------------------------- ## SD card connection