kopia lustrzana https://github.com/SP8EBC/ParaTNC
opole config
rodzic
2637371ee4
commit
fad8ef5d17
|
@ -0,0 +1,239 @@
|
|||
/*
|
||||
* config.h
|
||||
*
|
||||
* Created on: 03.07.2017
|
||||
* Author: mateusz
|
||||
*/
|
||||
|
||||
#ifndef STATION_CONFIG_H_
|
||||
#define STATION_CONFIG_H_
|
||||
|
||||
/* ------------------ */
|
||||
/* MODES OF OPERATION */
|
||||
|
||||
#define _METEO // Enable meteo station
|
||||
#define _DIGI // Enable WIDE1-1 digipeater
|
||||
//#define _DIGI_ONLY_789 // Limit digipeater to handle only -7, -8 and -9 SSIDs
|
||||
//#define _VICTRON // Enable support for Victron VE.Direct protocol
|
||||
|
||||
|
||||
/* MODES OF OPERATION */
|
||||
/* ------------------ */
|
||||
|
||||
//#define PARATNC_HWREV_A
|
||||
//#define PARATNC_HWREV_B
|
||||
#define PARATNC_HWREV_C
|
||||
|
||||
/* ---------------------------- */
|
||||
/* WEATHER/METEO CONFIGURATION */
|
||||
|
||||
// If none of those three sources are chosen (uncommented) the software will use internal sensors
|
||||
|
||||
//#define _UMB_MASTER
|
||||
//#define _DAVIS_SERIAL
|
||||
#define _MODBUS_RTU // use Modbus RTU slave devices as a external meteo data source. For more configuration
|
||||
// (slave ids, registers...) please look into MODBUS RTU CONFIGURATION section of this file
|
||||
|
||||
#define _INTERNAL_AS_BACKUP // if defined ParaTNC will switch to internal sensors in case of
|
||||
// the communication with UMB/Dallas Serial/Modbus external sensors will hang up
|
||||
|
||||
|
||||
//#define _DALLAS_AS_TELEM // Use Dallas one-wire thermometer as a 5th telemetry channel
|
||||
// May be used even if _METEO is not enabled
|
||||
#define _DALLAS_SPLIT_PIN // Must be enabled for all ParaTNC hardware revisions
|
||||
|
||||
|
||||
/******** INTERNAL SENSORS CONFIGURATION *****************/
|
||||
|
||||
#define _ANEMOMETER_TX20 // Use TX20 as an internal anemometer
|
||||
//#define _ANEMOMETER_ANALOGUE // Use analogue/mechanical (like Davis 6410) as an internal anemometr
|
||||
//#define _ANEMOMETER_PULSES_IN_10SEC_PER_ONE_MS_OF_WINDSPEED 10
|
||||
|
||||
//#define _SENSOR_MS5611
|
||||
#define _SENSOR_BME280
|
||||
|
||||
#define _UMB_SLAVE_ID 1
|
||||
#define _UMB_SLAVE_CLASS 8
|
||||
#define _UMB_CHANNEL_WINDSPEED 460
|
||||
#define _UMB_CHANNEL_WINDGUSTS 440
|
||||
#define _UMB_CHANNEL_WINDDIRECTION 580
|
||||
#define _UMB_CHANNEL_TEMPERATURE 100
|
||||
#define _UMB_CHANNEL_QFE 300
|
||||
|
||||
/******** INTERNAL SENSORS CONFIGURATION *****************/
|
||||
|
||||
/* WEATHER/METEO CONFIGURATION */
|
||||
/* ---------------------------- */
|
||||
|
||||
//#define _MUTE_RF // TODO: Not yet implemented - This will make station RXonly and disable all data transmission
|
||||
//#define _MUTE_OWN // TODO: Not yet implemented - This will disable all self-generated packets (wx, telemetry, beacon)
|
||||
// and switch device to "pure" kiss TNC operation. Packets from PC will be transmitted normally.
|
||||
|
||||
// Coordines should be in APRS decimal format DDDMM.SS for Longitude and DDMM.SS for latitude
|
||||
#define _CALL "SR6WXP"
|
||||
#define _SSID 0
|
||||
#define _LAT 5038.00
|
||||
#define _LATNS 'N'
|
||||
#define _LON 01747.00
|
||||
#define _LONWE 'E'
|
||||
#define _COMMENT "DigiW1 + WX ~ Lotnisko Polska Nowa Wies ~ https://www.facebook.com/aeroklub.opolski"
|
||||
|
||||
// You can use only one of these below defines to choose symbol. Meteo data are are always transmitted with blue WX symbol
|
||||
//#define _SYMBOL_DIGI // uncomment if you want digi symbol(green star with D inside)
|
||||
#define _SYMBOL_WIDE1_DIGI // uncomment if you want 'little' digi symbol (green star with digit 1 overlaid)
|
||||
//#define _SYMBOL_HOUSE // uncomment if you want house symbol
|
||||
//#define _SYMBOL_RXIGATE // uncomment if you want rxigate symbol (black diamond with R)
|
||||
//#define _SYMBOL_IGATE // uncomment if you want igate symol (black diamond with I)
|
||||
|
||||
// Or you can keep commented all symbol defines and choose custom one based on data from APRS symbols table
|
||||
//#define _SYMBOL_F '/'
|
||||
//#define _SYMBOL_S '#'
|
||||
|
||||
// Uncomment one of these two defines to choose what path You want. If you uncommend both of them or
|
||||
// if you keep both commended path will be completely disabled. CALL-S>AKLPRZ:data
|
||||
//#define _WIDE1_PATH // CALL-S>AKLPRZ,WIDE1-1:data
|
||||
#define _WIDE21_PATH // CALL-S>AKLPRZ,WIDE2-1:data
|
||||
|
||||
// Comment this to disable beacon auto sending during startup (this can be risky if RF feedback occur)
|
||||
//#define _BCN_ON_STARTUP
|
||||
|
||||
#define _WX_INTERVAL 4 // WX packet interval in minutes
|
||||
#define _BCN_INTERVAL 35 // Own beacon interval in minutes
|
||||
|
||||
#define _PTT_PUSHPULL // Uncomment this if you want PTT line to work as Push-pull instead of Open Drain
|
||||
#define _SERIAL_BAUDRATE 9600
|
||||
|
||||
// Transmitting delay
|
||||
#define _DELAY_BASE 8 // * 50ms. For example setting 10 gives 500msec delay. Maximum value is 20
|
||||
//#define _RANDOM_DELAY // adds random delay TO fixed time set by _DELAY_BASE. This additional time can be
|
||||
// from 100ms up to 1 sec in 100ms steps. Values are drawn from samples going from ADC
|
||||
// so it is better to use Unsquelched output in radio to provide much more randomness
|
||||
//After waiting time declared above ParaTNC will check DCD (Data Carrier Detect) flag, which works as some
|
||||
//kind of semaphore. If radio channel is not occupied by any other transmission TX will be keyed up immediately,
|
||||
//otherwise software will wait for clear conditions.
|
||||
|
||||
// Few IMPORTANT hints about setting transmit delay properly.
|
||||
//
|
||||
// Transmit delay is key parameter to maintain RF network free from packet losses and collisions. If your station will be
|
||||
// installed on tall object, without any other digi's close to it, you can set _DELAY_BASE to very low value and disable
|
||||
// _RANDOM_DELAY. If you wanna rather auxiliary station, witch should only fill gap in RF coverage in small area, then
|
||||
// _DELAY_BASE parameter should be not less than 12 (600msec), the smallest range the higher _DELAY_BASE should be.
|
||||
// Additionally for gapfillers (auxiliary stations) _RANDOM_DELAY schould be enabled.
|
||||
//
|
||||
// This delay will ensure that while other station will be transmitting repeated packets from mobile, Yours will keep
|
||||
// always quiet and won't jam RF network. This greatly improve DCD based access to channel. Various controllers uses
|
||||
// various lenght of preamble, some of them produce signal which might be impossible to decode by ParaTNC, so DCD
|
||||
// is only one part of effective multiaccess to medium.
|
||||
|
||||
/* ---------------------------- */
|
||||
/* MODBUS RTU CONFIGURATION */
|
||||
|
||||
// scaling coefficients are used as follows
|
||||
//
|
||||
// A * x ^ 2 + B * x + C
|
||||
// real value = ---------------------------
|
||||
// D
|
||||
//
|
||||
// because of that D cannot be set to zero
|
||||
#define _RTU_SLAVE_SPEED 9600u
|
||||
#define _RTU_SLAVE_PARITY 0
|
||||
#define _RTU_SLAVE_STOP_BITS 2
|
||||
|
||||
#define _RTU_SLAVE_ID_1 0x01
|
||||
#define _RTU_SLAVE_FUNC_1 0x03
|
||||
#define _RTU_SLAVE_ADDR_1 0x00
|
||||
#define _RTU_SLAVE_LENGHT_1 0x04
|
||||
#define _RTU_SLAVE_SCALING_A_1 0
|
||||
#define _RTU_SLAVE_SCALING_B_1 1
|
||||
#define _RTU_SLAVE_SCALING_C_1 0
|
||||
#define _RTU_SLAVE_SCALING_D_1 10
|
||||
|
||||
#define _RTU_SLAVE_ID_2 0x01
|
||||
#define _RTU_SLAVE_FUNC_2 0x03
|
||||
#define _RTU_SLAVE_ADDR_2 0x01
|
||||
//#define _RTU_SLAVE_LENGHT_2 0x01
|
||||
#define _RTU_SLAVE_SCALING_A_2 0
|
||||
#define _RTU_SLAVE_SCALING_B_2 1
|
||||
#define _RTU_SLAVE_SCALING_C_2 0
|
||||
#define _RTU_SLAVE_SCALING_D_2 1
|
||||
|
||||
#define _RTU_SLAVE_ID_3 0x01
|
||||
#define _RTU_SLAVE_FUNC_3 0x03
|
||||
#define _RTU_SLAVE_ADDR_3 0x02
|
||||
//#define _RTU_SLAVE_LENGHT_3 0x01
|
||||
#define _RTU_SLAVE_SCALING_A_3 0
|
||||
#define _RTU_SLAVE_SCALING_B_3 1
|
||||
#define _RTU_SLAVE_SCALING_C_3 0
|
||||
#define _RTU_SLAVE_SCALING_D_3 1
|
||||
|
||||
#define _RTU_SLAVE_ID_4 0x01
|
||||
#define _RTU_SLAVE_FUNC_4 0x03
|
||||
#define _RTU_SLAVE_ADDR_4 0x03
|
||||
//#define _RTU_SLAVE_LENGHT_4 0x01
|
||||
#define _RTU_SLAVE_SCALING_A_4 0
|
||||
#define _RTU_SLAVE_SCALING_B_4 1
|
||||
#define _RTU_SLAVE_SCALING_C_4 0
|
||||
#define _RTU_SLAVE_SCALING_D_4 1
|
||||
|
||||
//#define _RTU_SLAVE_TEMPERATURE_SOURCE 1
|
||||
#define _RTU_SLAVE_HUMIDITY_SOURCE 2
|
||||
//#define _RTU_SLAVE_PRESSURE_SOURCE 3
|
||||
//#define _RTU_SLAVE_WIND_DIRECTION_SORUCE 4
|
||||
//#define _RTU_SLAVE_WIND_SPEED_SOURCE 4
|
||||
|
||||
|
||||
/* MODBUS RTU CONFIGURATION */
|
||||
/* ---------------------------- */
|
||||
|
||||
// Do not touch this
|
||||
#if defined (_SYMBOL_DIGI) && !defined (_SYMBOL_WIDE1_DIGI) && !defined (_SYMBOL_HOUSE) && !defined (_SYMOL_RXIGATE) &&\
|
||||
!defined (_SYMBOL_IGATE)
|
||||
#define _SYMBOL_F '/'
|
||||
#define _SYMBOL_S '#'
|
||||
#elif !defined (_SYMBOL_DIGI) && defined (_SYMBOL_WIDE1_DIGI) && !defined (_SYMBOL_HOUSE) && !defined (_SYMOL_RXIGATE) &&\
|
||||
!defined (_SYMBOL_IGATE)
|
||||
#define _SYMBOL_F '1'
|
||||
#define _SYMBOL_S '#'
|
||||
#elif !defined (_SYMBOL_DIGI) && !defined (_SYMBOL_WIDE1_DIGI) && defined (_SYMBOL_HOUSE) && !defined (_SYMOL_RXIGATE) &&\
|
||||
!defined (_SYMBOL_IGATE)
|
||||
#define _SYMBOL_F '/'
|
||||
#define _SYMBOL_S '-'
|
||||
#elif !defined (_SYMBOL_DIGI) && !defined (_SYMBOL_WIDE1_DIGI) && !defined (_SYMBOL_HOUSE) && defined (_SYMOL_RXIGATE) &&\
|
||||
!defined (_SYMBOL_IGATE)
|
||||
#define _SYMBOL_F 'I'
|
||||
#define _SYMBOL_S '&'
|
||||
#elif !defined (_SYMBOL_DIGI) && !defined (_SYMBOL_WIDE1_DIGI) && !defined (_SYMBOL_HOUSE) && !defined (_SYMOL_RXIGATE) &&\
|
||||
defined (_SYMBOL_IGATE)
|
||||
#define _SYMBOL_F 'R'
|
||||
#define _SYMBOL_S '&'
|
||||
#elif !defined (_SYMBOL_F) && !defined (_SYMBOL_S)
|
||||
#error "Missing symbol configuration in station_config.h"
|
||||
#elif defined (_SYMBOL_F) && defined (_SYMBOL_S)
|
||||
#else
|
||||
#error "Wrong symbol configuration in station_config.h"
|
||||
#endif
|
||||
#if defined (_METEO) && !defined (_DIGI)
|
||||
#define _DIGI
|
||||
#endif
|
||||
|
||||
#if defined(PARATNC_HWREV_A) && (defined (_METEO) || defined (_DALLAS_AS_TELEM)) && !defined(_DALLAS_SPLIT_PIN)
|
||||
#define _DALLAS_SPLIT_PIN
|
||||
#endif
|
||||
|
||||
#if defined(PARATNC_HWREV_B) && (defined (_METEO) || defined (_DALLAS_AS_TELEM)) && !defined(_DALLAS_SPLIT_PIN)
|
||||
#define _DALLAS_SPLIT_PIN
|
||||
#endif
|
||||
|
||||
#if defined(_ANEMOMETER_TX20) && defined(_ANEMOMETER_ANALOGUE)
|
||||
#error "You cannot use two anemometers at once!!!"
|
||||
#endif
|
||||
|
||||
#if defined(_MOBUS_RTU) && defined(_DAVIS_SERIAL)
|
||||
#error "You cannot use modbus RTU devices and Davis weather station at once!!!"
|
||||
#endif
|
||||
|
||||
#if !defined(_ANEMOMETER_TX20) && !defined(_ANEMOMETER_ANALOGUE) && !defined(_UMB_MASTER) && defined(_METEO)
|
||||
#define _ANEMOMETER_TX20
|
||||
#endif
|
||||
|
||||
#endif /* STATION_CONFIG_H_ */
|
Ładowanie…
Reference in New Issue