mirror
/
SP8EBC-ParaTNC
kopia lustrzana https://github.com/SP8EBC/ParaTNC
1
0
Forkuj 0
Kod Zgłoszenia Projekty Wydania Wiki Aktywność

new configuration for magurka wilkowicka

tatry_variant EA14
Mateusz Lubecki 2022-08-06 07:45:03 +02:00
rodzic 1a59d092ff
commit 3bc8608b23
1 zmienionych plików z 174 dodań i 17 usunięć
Pokaż statystyki Ściągnij plik aktualizacji Ściągnij plik porównania Expand all files Collapse all files

191
include/backups/sr9wxm.config
Wyświetl plik

@ -8,30 +8,52 @@
#ifndef STATION_CONFIG_H_
#define STATION_CONFIG_H_
//#define _POWERSAVE_NORMAL
//#define _POWERSAVE_AGGRESIVE
/* ------------------ */
/* MODES OF OPERATION */
#define _METEO // Enable meteo station
#define _DIGI // Enable WIDE1-1 digipeater
#define _DIGI_ONLY_789 // Limit digipeater to handle only -7, -8 and -9 SSIDs
//#define _DIGI // Enable WIDE1-1 digipeater
#define _DIGI_VISCOUS
//#define _DIGI_ONLY_789 // Limit digipeater to handle only -7, -8 and -9 SSIDs
//#define _VICTRON // Enable support for Victron VE.Direct protocol
//#define _UMB_MASTER
//#define _GSM // only for ParaMETEO
#define _WX_DOUBLE_TRANSMIT
/* MODES OF OPERATION */
/* ------------------ */
//#define PARATNC_HWREV_A
//#define PARATNC_HWREV_B
#define PARATNC_HWREV_C
//#define PARAMETEO
/* ---------------------------- */
/* WEATHER/METEO CONFIGURATION */
// If none of those three sources are chosen (uncommented) the software will use internal sensors
//#define _UMB_MASTER
//#define _DAVIS_SERIAL
//#define _MODBUS_RTU // use Modbus RTU slave devices as a external meteo data source. For more configuration
// (slave ids, registers...) please look into MODBUS RTU CONFIGURATION section of this file
#define _INTERNAL_AS_BACKUP // if defined ParaTNC will switch to internal sensors in case of
// the communication with UMB/Dallas Serial/Modbus external sensors will hang up
//#define _DALLAS_AS_TELEM // Use Dallas one-wire thermometer as a 5th telemetry channel
// May be used even if _METEO is not enabled
#define _DALLAS_SPLIT_PIN
//#define _ANEMOMETER_TX20
#define _ANEMOMETER_ANALOGUE
#define _DALLAS_SPLIT_PIN // Must be enabled for all ParaTNC hardware revisions
/******** INTERNAL SENSORS CONFIGURATION *****************/
//#define _ANEMOMETER_TX20 // Use TX20 as an internal anemometer
#define _ANEMOMETER_ANALOGUE // Use analogue/mechanical (like Davis 6410) as an internal anemometr
#define _ANEMOMETER_PULSES_IN_10SEC_PER_ONE_MS_OF_WINDSPEED 10
//#define _SENSOR_MS5611
@ -45,6 +67,33 @@
#define _UMB_CHANNEL_TEMPERATURE 100
#define _UMB_CHANNEL_QFE 300
/******** INTERNAL SENSORS CONFIGURATION *****************/
/*************** DATA SOURCES CONFIG ***********************/
#define _TEMPERATURE_INTERNAL
//#define _TEMPERATURE_UMB
//#define _TEMPERATURE_RTU
//#define _TEMPERATURE_DAVIS
//
#define _PRESSURE_INTERNAL
//#define _PRESSURE_UMB
//#define _PRESSURE_RTU
//#define _PRESSURE_DAVIS
//
#define _HUMIDITY_INTERNAL
//#define _HUMIDITY_UMB
//#define _HUMIDITY_RTU
//#define _HUMIDITY_DAVIS
//
//
#define _WIND_INTERNAL
//#define _WIND_UMB
//#define _WIND_RTU
//#define _WIND_FULL_RTU
//#define _WIND_DAVIS
/*************** DATA SOURCES CONFIG ***********************/
/* WEATHER/METEO CONFIGURATION */
/* ---------------------------- */
@ -59,7 +108,7 @@
#define _LATNS 'N'
#define _LON 01907.85
#define _LONWE 'E'
#define _COMMENT "WX + DigiW1 SSID789 only - GOSIR Magurka Wilkowicka - sp8ebc@interia.pl"
#define _COMMENT "WX + DigiW1 Viscous - GOSIR Magurka Wilkowicka - sp8ebc@interia.pl"
// You can use only one of these below defines to choose symbol. Meteo data are are always transmitted with blue WX symbol
//#define _SYMBOL_DIGI // uncomment if you want digi symbol(green star with D inside)
@ -67,6 +116,7 @@
//#define _SYMBOL_HOUSE // uncomment if you want house symbol
//#define _SYMBOL_RXIGATE // uncomment if you want rxigate symbol (black diamond with R)
//#define _SYMBOL_IGATE // uncomment if you want igate symol (black diamond with I)
//#define _SYMBOL_SAILBOAT
// Or you can keep commented all symbol defines and choose custom one based on data from APRS symbols table
//#define _SYMBOL_F '/'
@ -75,19 +125,21 @@
// Uncomment one of these two defines to choose what path You want. If you uncommend both of them or
// if you keep both commended path will be completely disabled. CALL-S>AKLPRZ:data
//#define _WIDE1_PATH // CALL-S>AKLPRZ,WIDE1-1:data
#define _WIDE21_PATH // CALL-S>AKLPRZ,WIDE2-1:data
//#define _WIDE21_PATH // CALL-S>AKLPRZ,WIDE2-1:data
// Comment this to disable beacon auto sending during startup (this can be risky if RF feedback occur)
//#define _BCN_ON_STARTUP
#define _BCN_ON_STARTUP
#define _WX_INTERVAL 4 // WX packet interval in minutes
#define _BCN_INTERVAL 29 // Own beacon interval in minutes
#define _BCN_INTERVAL 125 // Own beacon interval in minutes
#define _PTT_PUSHPULL // Uncomment this if you want PTT line to work as Push-pull instead of Open Drain
#define _SERIAL_BAUDRATE 19200
#define _SERIAL_BAUDRATE 9600
#define _DIGI_VISCOUS_DEALY 2
// Transmitting delay
#define _DELAY_BASE 22 // * 50ms. For example setting 10 gives 500msec delay. Maximum value is 20
#define _DELAY_BASE 20 // * 50ms. For example setting 10 gives 500msec delay. Maximum value is 20
//#define _RANDOM_DELAY // adds random delay TO fixed time set by _DELAY_BASE. This additional time can be
// from 100ms up to 1 sec in 100ms steps. Values are drawn from samples going from ADC
// so it is better to use Unsquelched output in radio to provide much more randomness
@ -108,6 +160,103 @@
// various lenght of preamble, some of them produce signal which might be impossible to decode by ParaTNC, so DCD
// is only one part of effective multiaccess to medium.
/* ---------------------------- */
/* MODBUS RTU CONFIGURATION */
// scaling coefficients are used as follows
//
// A * x ^ 2 + B * x + C
// real value = ---------------------------
// D
//
// because of that D cannot be set to zero
#define _RTU_SLAVE_SPEED 9600u
#define _RTU_SLAVE_PARITY 0
#define _RTU_SLAVE_STOP_BITS 2
#define _RTU_SLAVE_ID_1 0x01
#define _RTU_SLAVE_FUNC_1 0x03
#define _RTU_SLAVE_ADDR_1 0x00
#define _RTU_SLAVE_LENGHT_1 0x01
#define _RTU_SLAVE_SCALING_A_1 0
#define _RTU_SLAVE_SCALING_B_1 1
#define _RTU_SLAVE_SCALING_C_1 0
#define _RTU_SLAVE_SCALING_D_1 10
#define _RTU_SLAVE_ID_2 0x01
#define _RTU_SLAVE_FUNC_2 0x03
#define _RTU_SLAVE_ADDR_2 0x01
//#define _RTU_SLAVE_LENGHT_2 0x01
#define _RTU_SLAVE_SCALING_A_2 0
#define _RTU_SLAVE_SCALING_B_2 1
#define _RTU_SLAVE_SCALING_C_2 0
#define _RTU_SLAVE_SCALING_D_2 1
#define _RTU_SLAVE_ID_3 0x01
#define _RTU_SLAVE_FUNC_3 0x03
#define _RTU_SLAVE_ADDR_3 0x02
//#define _RTU_SLAVE_LENGHT_3 0x01
#define _RTU_SLAVE_SCALING_A_3 0
#define _RTU_SLAVE_SCALING_B_3 1
#define _RTU_SLAVE_SCALING_C_3 0
#define _RTU_SLAVE_SCALING_D_3 1
#define _RTU_SLAVE_ID_4 0x01
#define _RTU_SLAVE_FUNC_4 0x03
#define _RTU_SLAVE_ADDR_4 0x03
//#define _RTU_SLAVE_LENGHT_4 0x01
#define _RTU_SLAVE_SCALING_A_4 0
#define _RTU_SLAVE_SCALING_B_4 1
#define _RTU_SLAVE_SCALING_C_4 0
#define _RTU_SLAVE_SCALING_D_4 1
#define _RTU_SLAVE_ID_5 0x00
#define _RTU_SLAVE_FUNC_5 0x00
#define _RTU_SLAVE_ADDR_5 0x03
//#define _RTU_SLAVE_LENGHT_4 0x01
#define _RTU_SLAVE_SCALING_A_5 0
#define _RTU_SLAVE_SCALING_B_5 1
#define _RTU_SLAVE_SCALING_C_5 0
#define _RTU_SLAVE_SCALING_D_5 1
#define _RTU_SLAVE_ID_6 0x00
#define _RTU_SLAVE_FUNC_6 0x00
#define _RTU_SLAVE_ADDR_6 0x00
//#define _RTU_SLAVE_LENGHT_4 0x01
#define _RTU_SLAVE_SCALING_A_6 0
#define _RTU_SLAVE_SCALING_B_6 1
#define _RTU_SLAVE_SCALING_C_6 0
#define _RTU_SLAVE_SCALING_D_6 1
//#define _RTU_SLAVE_TEMPERATURE_SOURCE 1
#define _RTU_SLAVE_HUMIDITY_SOURCE 2
//#define _RTU_SLAVE_PRESSURE_SOURCE 3
//#define _RTU_SLAVE_WIND_DIRECTION_SORUCE 4
//#define _RTU_SLAVE_WIND_SPEED_SOURCE 4
/* MODBUS RTU CONFIGURATION */
/* ---------------------------- */
/* ---------------------------- */
/* GSM and APRS-IS and API */
#define _GSM_APN_NAME "internet\0"
#define _GSM_APN_USER "internet\0"
#define _GSM_APN_PASS "internet\0"
//#define _GSM_API_ENABLE
#define _GSM_API_BASE_URL "http://78.88.56.14:8080/meteo_backend"
#define _GSM_API_STATION_NAME "pilsko"
//#define _GSM_APRSIS_ENABLE
#define _GSM_APRSIS_PASSCODE 16823
#define _GSM_APRSIS_PORT 14580
#define _GSM_APRSIS_ADDRES "euro.aprs2.net\0"
/* GSM and APRS-IS and API */
/* ---------------------------- */
// Do not touch this
#if defined (_SYMBOL_DIGI) && !defined (_SYMBOL_WIDE1_DIGI) && !defined (_SYMBOL_HOUSE) && !defined (_SYMOL_RXIGATE) &&\
@ -130,15 +279,19 @@
defined (_SYMBOL_IGATE)
#define _SYMBOL_F 'R'
#define _SYMBOL_S '&'
#elif !defined (_SYMBOL_DIGI) && !defined (_SYMBOL_WIDE1_DIGI) && !defined (_SYMBOL_HOUSE) && !defined (_SYMOL_RXIGATE) &&\
!defined (_SYMBOL_IGATE) && defined(_SYMBOL_SAILBOAT)
#define _SYMBOL_F '/'
#define _SYMBOL_S 'Y'
#elif !defined (_SYMBOL_F) && !defined (_SYMBOL_S)
#error "Missing symbol configuration in station_config.h"
#elif defined (_SYMBOL_F) && defined (_SYMBOL_S)
#else
#error "Wrong symbol configuration in station_config.h"
#endif
#if defined (_METEO) && !defined (_DIGI)
#define _DIGI
#endif
//#if defined (_METEO) && !defined (_DIGI)
//#define _DIGI
//#endif
#if defined(PARATNC_HWREV_A) && (defined (_METEO) || defined (_DALLAS_AS_TELEM)) && !defined(_DALLAS_SPLIT_PIN)
#define _DALLAS_SPLIT_PIN
@ -152,6 +305,10 @@
#error "You cannot use two anemometers at once!!!"
#endif
#if defined(_MOBUS_RTU) && defined(_DAVIS_SERIAL)
#error "You cannot use modbus RTU devices and Davis weather station at once!!!"
#endif
#if !defined(_ANEMOMETER_TX20) && !defined(_ANEMOMETER_ANALOGUE) && !defined(_UMB_MASTER) && defined(_METEO)
#define _ANEMOMETER_TX20
#endif