OpenBuilds CONTROL

	X WORK 0.000	Goto X0 (Work Coord) (G0 X0) Goto X0 (Machine Coord) (G53 G0 X0) Probe X-Zero Wizard New! Probe XYZ-Zero Wizard New!
	Y WORK 0.000	Goto Y0 (Work Coord) (G0 Y0) Goto Y0 (Machine Coord) (G53 G0 Y0) Probe Y-Zero Wizard New! Probe XYZ-Zero Wizard New!
	Z WORK 0.000	Goto Z0 (Work Coord) (G0 Z0) Goto Z0 (Machine Coord) (G53 G0 Z0) Probe Z-Zero Wizard New! Probe XYZ-Zero Wizard New!
	GOTOZERO (Work Coord) (G0 Z5, G0 X0 Y0, G0 Z0) (Retract Z to Work Coord Z5) GOTOZERO (Z Machine Coord, XY Work Coord) (G53 G0 Z0, G0 X0 Y0, G0 Z0) (Retract Z to Machine Coord) GOTOZERO (Machine Coord) (G53 G0 Z0, G53 G0 X0 Y0)	Go to Pre-Defined Position (G28) Set Pre-Defined Position (G28.1) Go to Pre-Defined Position (G30) Set Pre-Defined Position (G30.1)

Incremental Jog

app-notifition

Continuous Jog

Inputs / Endstops

PIN	Status
X-Limit	NOCOMM
Y-Limit	NOCOMM
Z-Limit	NOCOMM
Probe	NOCOMM
Door Sensor	NOCOMM
Buttons	NOCOMM NOCOMM NOCOMM

Communications

Value	Status
Installed Version	NOCOMM
Backend Queue Blocked	NOCOMM
Connection Status	NOCOMM
Connected To	NOCOMM
Serial Queue	NOCOMM
Websocket Status	NOCOMM

Firmware Parameters

Value	Status
Variable Spindle	OFF
Laser Mode Enabled ($32 Setting)	OFF
Grbl-Servo Installed	OFF
Line Numbers Enabled	OFF
Mist Cooling Enabled	OFF
CoreXY Enabled	OFF
Parking Motion Enabled	OFF
Homing Force Origin Enabled	OFF
Single Axis Homing	OFF
Two Limit Switches on Axis Enabled	OFF
Allow Feed Override in Probe	OFF
Restore EEPROM $-settings Disabled	OFF
Restore EEPROM parameter Disabled	OFF
Build Info Write Disabled	OFF
Force Sync on EEPROM write Disabled	OFF
Force Sync on WCO Disabled	OFF
Homing Init Lock	OFF

Power Settings

Setting	Status
USB Selective Suspend on AC Power	NOCOMM
USB Selective Suspend on Battery Power	NOCOMM
We recommend USB Selective Suspend be Disabled to avoid USB issues

Changelog

Not Connected

Job Queue: 0

Firmware Flashing Tool

You can use this wizard to flash Firmware onto compatible controllers
Only use with care, or when instructed by Support

Controller Type

Machine Style

Door Interlock

Port

Flattening / Surfacing Tool

Router Bit Diameter

Diameter of your bit / endmill

Stepover

Stepover between passes

Feedrate

Cutting speed

Width
X-Axis

Length
Y-Axis

Width and Length of the area to machine flat

Skim Depth

How much material to remove

Spindle RPM

Spindle RPM for variable spindles

NB: make sure your spindle is 100% perpendicular (trammed) to your bed, before running a Surfacing operation. Incorrectly trammed spindles will cause uneven machining of the surface, leading to pitting and uneven surface finish

You can use the Surfacing Tool to

Prepare / flatten your spoilboard
Level off stock

Update Ready

Updated version 1.0.100 has finished downloading and is ready to be installed!
Note that proceeding will:

Stop any running jobs
Shut down this instance of OpenBuilds CONTROL
Launch the installer for the new version

You may want to wait until your machine is idle, and it it's a convenient time for you to do this, before continuing

Jog Widget

You can use your mobile device as an handheld Jog interface. To get started, open a web-browser on your Mobile device and navigate to
http://0.0.0.0:3000/jog.html
or scan the QR Code below

Probing Wizard

Automatic Probe Routine: This routine is used to find the XYZ origins, as well as automatically determine endmill diameter.

Position the endmill above the hole in the probe plate as shown to the left just above the plate, clip on the magnetic connecting clip, then click the Confirm Probe Position button to continue...

XYZ Probe Routine: This routine is used to find the XYZ origins

Position the endmill above the hole in the probe plate as shown to the left just above the plate, clip on the magnetic connecting clip, then click the Confirm Probe Position button to continue...

X Probe Routine: This routine is used to find the X origin

Position the endmill to the left of the probe plate as shown, clip on the magnetic connecting clip, then click the Confirm Probe Position button to continue...

Y Probe Routine: This routine is used to find the Y origin

Position the endmill in front of the probe plate as shown, clip on the magnetic connecting clip, then click the Confirm Probe Position button to continue...

Z Probe Routine: This routine is used to find the Z origin

Position the endmill above the probe plate as shown, clip on the magnetic connecting clip, then click the Confirm Probe Position button to continue...

Endmill Probe Routine: This routine is used to find the Endmill Diameter

Position the endmill above the hole in the probe plate as shown to the left just above the plate, clip on the magnetic connecting clip, then click the Confirm Probe Position button to continue...

This operation will perform an XYZ probe to establish the plate position, then using the hole in the plate, it will measure and calculate the Endmill Diameter and display it onscreen.
This operation will NOT set any work-coordinates!



Or use the Keyboard to Jog

Endmill Diameter

Plate Thickness

Where is the XY Zero Datum / Origin in your CAM setup, relative to the front-left corner we are probing?

If the origin is not Front, Left (Default): Then provide stock dimensions to calculate correct offset of X0, Y0:
Width Length

Probe Type:

OpenBuilds XYZ Probe Plus

Edit Custom Probe

Completed