Hamlib/yaesu/frg8800.c

255 wiersze
7.0 KiB
C

/*
* frg8800.c - (C) Stephane Fillod 2002-2004
*
* This shared library provides an API for communicating
* via serial interface to an FRG-8800 using the "CAT" interface
*
*
* This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU Lesser General Public
* License as published by the Free Software Foundation; either
* version 2.1 of the License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* Lesser General Public License for more details.
*
* You should have received a copy of the GNU Lesser General Public
* License along with this library; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
*
*/
#ifdef HAVE_CONFIG_H
#include "config.h"
#endif
#include <stdlib.h>
#include <string.h> /* String function definitions */
#include <unistd.h> /* UNIX standard function definitions */
#include "hamlib/rig.h"
#include "serial.h"
#include "misc.h"
#include "yaesu.h"
/* Private helper function prototypes */
#define FRG8800_MODES (RIG_MODE_CW|RIG_MODE_SSB|RIG_MODE_AM|RIG_MODE_FM|RIG_MODE_WFM)
#define FRG8800_VFOS (RIG_VFO_A)
#define FRG8800_ANTS 0
static int frg8800_open(RIG *rig);
static int frg8800_close(RIG *rig);
static int frg8800_set_freq(RIG *rig, vfo_t vfo, freq_t freq);
static int frg8800_set_mode(RIG *rig, vfo_t vfo, rmode_t mode, pbwidth_t width);
static int frg8800_set_powerstat(RIG *rig, powerstat_t status);
/*
* frg8800 rigs capabilities.
* Also this struct is READONLY!
*
*/
const struct rig_caps frg8800_caps =
{
.rig_model = RIG_MODEL_FRG8800,
.model_name = "FRG-8800",
.mfg_name = "Yaesu",
.version = "0.2",
.copyright = "LGPL",
.status = RIG_STATUS_UNTESTED,
.rig_type = RIG_TYPE_RECEIVER,
.ptt_type = RIG_PTT_NONE,
.dcd_type = RIG_DCD_NONE,
.port_type = RIG_PORT_SERIAL,
.serial_rate_min = 4800,
.serial_rate_max = 4800,
.serial_data_bits = 8,
.serial_stop_bits = 2,
.serial_parity = RIG_PARITY_NONE,
.serial_handshake = RIG_HANDSHAKE_NONE,
.write_delay = 0,
.post_write_delay = 300,
.timeout = 2000,
.retry = 0,
.has_get_func = RIG_FUNC_NONE,
.has_set_func = RIG_FUNC_NONE,
.has_get_level = RIG_LEVEL_NONE,
.has_set_level = RIG_LEVEL_NONE,
.has_get_parm = RIG_PARM_NONE,
.has_set_parm = RIG_PARM_NONE,
.vfo_ops = RIG_OP_NONE,
.preamp = { RIG_DBLST_END, },
.attenuator = { RIG_DBLST_END, },
.max_rit = Hz(0),
.max_xit = Hz(0),
.max_ifshift = Hz(0),
.targetable_vfo = RIG_TARGETABLE_FREQ,
.transceive = RIG_TRN_OFF,
.bank_qty = 0,
.chan_desc_sz = 0,
.chan_list = {
RIG_CHAN_END,
},
.rx_range_list1 = {
{kHz(150), MHz(29.999), FRG8800_MODES, -1, -1, FRG8800_VFOS, FRG8800_ANTS },
{MHz(118), MHz(173.999), FRG8800_MODES, -1, -1, FRG8800_VFOS, FRG8800_ANTS },
RIG_FRNG_END,
}, /* Region 1 rx ranges */
.tx_range_list1 = {
RIG_FRNG_END,
}, /* region 1 TX ranges */
.rx_range_list2 = {
{kHz(150), MHz(29.999), FRG8800_MODES, -1, -1, FRG8800_VFOS, FRG8800_ANTS },
{MHz(118), MHz(173.999), FRG8800_MODES, -1, -1, FRG8800_VFOS, FRG8800_ANTS },
RIG_FRNG_END,
}, /* Region 2 rx ranges */
.tx_range_list2 = {
RIG_FRNG_END,
}, /* region 2 TX ranges */
.tuning_steps = {
{FRG8800_MODES, Hz(25)},
RIG_TS_END,
},
/* mode/filter list, remember: order matters! */
.filters = {
{RIG_MODE_AM, kHz(6)},
{RIG_MODE_SSB | RIG_MODE_CW | RIG_MODE_AM, kHz(2.7)},
{RIG_MODE_CW, Hz(500)},
{RIG_MODE_FM, kHz(12.5)},
{RIG_MODE_WFM, kHz(230)}, /* optional unit */
RIG_FLT_END,
},
.rig_open = frg8800_open,
.rig_close = frg8800_close,
.set_freq = frg8800_set_freq,
.set_mode = frg8800_set_mode,
.set_powerstat = frg8800_set_powerstat,
};
#define MODE_SET_AM 0x00
#define MODE_SET_LSB 0x01
#define MODE_SET_USB 0x02
#define MODE_SET_CW 0x03
#define MODE_SET_FM 0x0c
#define MODE_SET_FMW 0x04
/*
* frg8800_open routine
*
*/
int frg8800_open(RIG *rig)
{
unsigned char cmd[YAESU_CMD_LENGTH] = { 0x00, 0x00, 0x00, 0x00, 0x00};
rig_debug(RIG_DEBUG_TRACE, "%s: called\n", __func__);
/* send Ext Cntl ON: Activate CAT */
return write_block(&rig->state.rigport, (char *) cmd, YAESU_CMD_LENGTH);
}
int frg8800_close(RIG *rig)
{
unsigned char cmd[YAESU_CMD_LENGTH] = { 0x00, 0x00, 0x00, 0x80, 0x00};
rig_debug(RIG_DEBUG_TRACE, "%s: called\n", __func__);
/* send Ext Cntl OFF: Deactivate CAT */
return write_block(&rig->state.rigport, (char *) cmd, YAESU_CMD_LENGTH);
}
int frg8800_set_freq(RIG *rig, vfo_t vfo, freq_t freq)
{
unsigned char cmd[YAESU_CMD_LENGTH] = { 0x00, 0x00, 0x00, 0x00, 0x01};
rig_debug(RIG_DEBUG_TRACE, "%s: called\n", __func__);
/* store bcd format in cmd (LSB) */
to_bcd(cmd, freq / 10, 8);
/* Byte1: 100Hz's and 25Hz step code */
cmd[0] = (cmd[0] & 0xf0) | (1 << ((((long long)freq) % 100) / 25));
/* Frequency set */
return write_block(&rig->state.rigport, (char *) cmd, YAESU_CMD_LENGTH);
}
int frg8800_set_mode(RIG *rig, vfo_t vfo, rmode_t mode, pbwidth_t width)
{
unsigned char cmd[YAESU_CMD_LENGTH] = { 0x00, 0x00, 0x00, 0x00, 0x80};
unsigned char md;
rig_debug(RIG_DEBUG_TRACE, "%s: frg8800_set_mode called %s\n", __func__,
rig_strrmode(mode));
/*
* translate mode from generic to frg8800 specific
*/
switch (mode)
{
case RIG_MODE_AM: md = MODE_SET_AM; break;
case RIG_MODE_CW: md = MODE_SET_CW; break;
case RIG_MODE_USB: md = MODE_SET_USB; break;
case RIG_MODE_LSB: md = MODE_SET_LSB; break;
case RIG_MODE_FM: md = MODE_SET_FM; break;
case RIG_MODE_WFM: md = MODE_SET_FMW; break;
default:
return -RIG_EINVAL; /* sorry, wrong MODE */
}
if (width != RIG_PASSBAND_NOCHANGE
&& width != RIG_PASSBAND_NORMAL
&& width < rig_passband_normal(rig, mode))
{
md |= 0x08;
}
cmd[3] = md;
/* Mode set */
return write_block(&rig->state.rigport, (char *) cmd, YAESU_CMD_LENGTH);
}
int frg8800_set_powerstat(RIG *rig, powerstat_t status)
{
unsigned char cmd[YAESU_CMD_LENGTH] = { 0x00, 0x00, 0x00, 0x00, 0x80};
rig_debug(RIG_DEBUG_TRACE, "%s: called\n", __func__);
cmd[3] = status == RIG_POWER_OFF ? 0xff : 0xfe;
/* Frequency set */
return write_block(&rig->state.rigport, (char *) cmd, YAESU_CMD_LENGTH);
}