Hamlib/rigs/rft/ekd500.c

130 wiersze
3.3 KiB
C

/*
* Hamlib RFT backend - EKD-500 description
* Copyright (c) 2003-2009 by Thomas B. Ruecker
*
*
* This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU Lesser General Public
* License as published by the Free Software Foundation; either
* version 2.1 of the License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* Lesser General Public License for more details.
*
* You should have received a copy of the GNU Lesser General Public
* License along with this library; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
*
*/
#ifdef HAVE_CONFIG_H
#include "config.h"
#endif
#include <stdlib.h>
#include <hamlib/rig.h>
#include "rft.h"
#define EKD500_MODES (RIG_MODE_SSB|RIG_MODE_CW|RIG_MODE_RTTY|RIG_MODE_AM|RIG_MODE_FM)
#define EKD500_FUNC (RIG_FUNC_NONE)
#define EKD500_LEVEL_ALL (RIG_LEVEL_NONE)
#define EKD500_PARM_ALL (RIG_PARM_NONE)
#define EKD500_VFO (RIG_VFO_A)
#define EKD500_VFO_OPS (RIG_OP_NONE)
/*
* EKD-500 rig capabilities.
*
* Documentation:
* http://www.premium-rx.org/ekd500.htm
*/
const struct rig_caps ekd500_caps =
{
RIG_MODEL(RIG_MODEL_EKD500),
.model_name = "EKD-500",
.mfg_name = "RFT",
.version = BACKEND_VER ".0",
.copyright = "LGPL",
.status = RIG_STATUS_ALPHA,
.rig_type = RIG_TYPE_RECEIVER,
.ptt_type = RIG_PTT_NONE,
.dcd_type = RIG_DCD_NONE,
.port_type = RIG_PORT_SERIAL,
.serial_rate_min = 300,
.serial_rate_max = 2400,
.serial_data_bits = 7,
.serial_stop_bits = 2,
.serial_parity = RIG_PARITY_EVEN,
.serial_handshake = RIG_HANDSHAKE_HARDWARE,
.write_delay = 0,
.post_write_delay = 1,
.timeout = 200,
.retry = 3,
.has_get_func = EKD500_FUNC,
.has_set_func = EKD500_FUNC,
.has_get_level = EKD500_LEVEL_ALL,
.has_set_level = RIG_LEVEL_SET(EKD500_LEVEL_ALL),
.has_get_parm = EKD500_PARM_ALL,
.has_set_parm = RIG_PARM_SET(EKD500_PARM_ALL),
.level_gran = {},
.parm_gran = {},
.ctcss_list = NULL,
.dcs_list = NULL,
.preamp = { RIG_DBLST_END },
.attenuator = { RIG_DBLST_END },
.max_rit = Hz(0),
.max_xit = Hz(0),
.max_ifshift = Hz(0),
.targetable_vfo = 0,
.transceive = RIG_TRN_OFF,
.bank_qty = 0,
.chan_desc_sz = 7,
.vfo_ops = EKD500_VFO_OPS,
.chan_list = {
RIG_CHAN_END, /* FIXME */
},
.rx_range_list1 = {
{kHz(10), MHz(30), EKD500_MODES, -1, -1, EKD500_VFO},
RIG_FRNG_END,
},
.tx_range_list1 = { RIG_FRNG_END, },
.rx_range_list2 = {
{kHz(10), MHz(30), EKD500_MODES, -1, -1, EKD500_VFO},
RIG_FRNG_END,
},
.tx_range_list2 = { RIG_FRNG_END, },
.tuning_steps = {
{EKD500_MODES, 10},
RIG_TS_END,
},
/* mode/filter list, remember: order matters! */
.filters = {
{RIG_MODE_SSB | RIG_MODE_CW | RIG_MODE_RTTY | RIG_MODE_AM, kHz(2.2)},
{RIG_MODE_FM, kHz(12)},
RIG_FLT_END,
},
.priv = NULL,
.set_freq = rft_set_freq,
};
/*
* Function definitions below
*/