Hamlib/icom/icom_defs.h

395 wiersze
14 KiB
C

/*
* Hamlib CI-V backend - defines for the ICOM "CI-V" interface.
* Copyright (c) 2000-2010 by Stephane Fillod
*
*
* This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU Lesser General Public
* License as published by the Free Software Foundation; either
* version 2.1 of the License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* Lesser General Public License for more details.
*
* You should have received a copy of the GNU Lesser General Public
* License along with this library; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
*
*/
#ifndef _ICOM_DEFS_H
#define _ICOM_DEFS_H 1
/*
* CI-V frame codes
*/
#define PR 0xfe /* Preamble code */
#define CTRLID 0xe0 /* Controllers's default address */
#define BCASTID 0x00 /* Broadcast address */
#define FI 0xfd /* End of message code */
#define ACK 0xfb /* OK code */
#define NAK 0xfa /* NG code */
#define COL 0xfc /* CI-V bus collision detected */
#define PAD 0xff /* Transmit padding */
#define ACKFRMLEN 6 /* reply frame length */
#define S_NONE -1
/*
* Arguments length in bytes
*/
#define CHAN_NB_LEN 2
#define BANK_NB_LEN 2
#define OFFS_LEN 3
/*
* Cn controller commands
*
Most radios have 2 or 3 recieve passbands available. Where only 2 are available they
are selected by 01 for wide and 02 for narrow Actual bandwidth is determined by the filters
installed. With the newer DSP rigs there are 3 presets 01 = wide 02 = middle and 03 = narrow.
Acutally you can set change any of these presets to any thing you want.
* Notes:
* The following only applies to IC-706.
* 1. When wide or normal op available: add "00" for wide, "01" normal
* Normal or narrow op: add "00" for normal, "01" for narrow
* Wide, normal or narrow op: add "00" for wide, "01" normal, "02" narrow
* 2. Memory channel number 1A=0100/1b=0101, 2A=0102/2b=0103,
* 3A=0104/3b=0105, C1=0106, C2=0107
*/
#define C_SND_FREQ 0x00 /* Send frequency data trancieve mode does not ack*/
#define C_SND_MODE 0x01 /* Send mode data, Sc for trancieve mode does not ack */
#define C_RD_BAND 0x02 /* Read band edge frequencies */
#define C_RD_FREQ 0x03 /* Read display frequency */
#define C_RD_MODE 0x04 /* Read display mode */
#define C_SET_FREQ 0x05 /* Set frequency data(1) */
#define C_SET_MODE 0x06 /* Set mode data, Sc */
#define C_SET_VFO 0x07 /* Set VFO */
#define C_SET_MEM 0x08 /* Set channel, Sc(2) */
#define C_WR_MEM 0x09 /* Write memory */
#define C_MEM2VFO 0x0a /* Memory to VFO */
#define C_CLR_MEM 0x0b /* Memory clear */
#define C_RD_OFFS 0x0c /* Read duplex offset frequency; default changes with HF/6M/2M */
#define C_SET_OFFS 0x0d /* Set duplex offset frequency */
#define C_CTL_SCAN 0x0e /* Control scan, Sc */
#define C_CTL_SPLT 0x0f /* Control split, and duplex mode Sc */
#define C_SET_TS 0x10 /* Set tuning step, Sc */
#define C_CTL_ATT 0x11 /* Set/get attenuator, Sc */
#define C_CTL_ANT 0x12 /* Set/get antenna, Sc */
#define C_CTL_ANN 0x13 /* Control announce (speech synth.), Sc */
#define C_CTL_LVL 0x14 /* Set AF/RF/squelch, Sc */
#define C_RD_SQSM 0x15 /* Read squelch condiction/S-meter level, Sc */
#define C_CTL_FUNC 0x16 /* Function settings (AGC,NB,etc.), Sc */
#define C_SND_CW 0x17 /* Send CW message */
#define C_SET_PWR 0x18 /* Set Power ON/OFF, Sc */
#define C_RD_TRXID 0x19 /* Read transceiver ID code */
#define C_CTL_MEM 0x1a /* Misc memory/bank/rig control functions, Sc */
#define C_SET_TONE 0x1b /* Set tone frequency */
#define C_CTL_PTT 0x1c /* Control Transmit On/Off, Sc */
#define C_CTL_MISC 0x7f /* Miscellaneous control, Sc */
/*
* Sc controller sub commands
*/
/*
* Set mode data (C_SET_MODE) sub commands
*/
#define S_LSB 0x00 /* Set to LSB */
#define S_USB 0x01 /* Set to USB */
#define S_AM 0x02 /* Set to AM */
#define S_CW 0x03 /* Set to CW */
#define S_RTTY 0x04 /* Set to RTTY */
#define S_FM 0x05 /* Set to FM */
#define S_WFM 0x06 /* Set to Wide FM */
#define S_CWR 0x07 /* Set to CW Reverse */
#define S_RTTYR 0x08 /* Set to RTTY Reverse */
#define S_AMS 0x11 /* Set to AMS */
#define S_PSK 0x12 /* 7800 PSK USB */
#define S_PSKR 0x13 /* 7800 PSK LSB */
#define S_R7000_SSB 0x05 /* Set to SSB on R-7000 */
/* filter width coding for older ICOM rigs with 2 filter width */
/* there is no special 'wide' for that rigs */
#define PD_MEDIUM_2 0x01 /* Medium */
#define PD_NARROW_2 0x02 /* Narrow */
/* filter width coding for newer ICOM rigs with 3 filter width */
#define PD_WIDE_3 0x01 /* Wide */
#define PD_MEDIUM_3 0x02 /* Medium */
#define PD_NARROW_3 0x03 /* Narrow */
/*
* Set VFO (C_SET_VFO) sub commands
*/
#define S_VFOA 0x00 /* Set to VFO A */
#define S_VFOB 0x01 /* Set to VFO B */
#define S_BTOA 0xa0 /* VFO A=B */
#define S_XCHNG 0xb0 /* Switch VFO A and B */
#define S_SUBTOMAIN 0xb1 /* MAIN = SUB */
#define S_DUAL_OFF 0xc0 /* Dual watch off */
#define S_DUAL_ON 0xc1 /* Dual watch on */
#define S_MAIN 0xd0 /* Select MAIN band */
#define S_SUB 0xd1 /* Select SUB band */
#define S_FRONTWIN 0xe0 /* Select front window */
/*
* Set MEM (C_SET_MEM) sub commands
*/
#define S_BANK 0xa0 /* Select memory bank */
/*
* Scan control (C_CTL_SCAN) subcommands
*/
#define S_SCAN_STOP 0x00 /* Stop scan/window scan */
#define S_SCAN_START 0x01 /* Programmed/Memory scan */
#define S_SCAN_PROG 0x02 /* Programmed scan */
#define S_SCAN_DELTA 0x03 /* Delta-f scan */
#define S_SCAN_WRITE 0x04 /* auto memory-write scan */
#define S_SCAN_FPROG 0x12 /* Fine programmed scan */
#define S_SCAN_FDELTA 0x13 /* Fine delta-f scan */
#define S_SCAN_MEM2 0x22 /* Memory scan */
#define S_SCAN_SLCTN 0x23 /* Selected number memory scan */
#define S_SCAN_SLCTM 0x24 /* Selected mode memory scan */
#define S_SCAN_PRIO 0x42 /* Priority / window scan */
#define S_SCAN_NSLCT 0xB0 /* Set as non select channel */
#define S_SCAN_SLCT 0xB1 /* Set as select channel */
#define S_SCAN_SL_NUM 0xB2 /* select programed mem scan 7800 only */
#define S_SCAN_RSMOFF 0xD0 /* Set scan resume OFF */
#define S_SCAN_RSMON 0xD3 /* Set scan resume ON */
/*
* Split control (S_CTL_SPLT) subcommands
*/
#define S_SPLT_OFF 0x00 /* Split OFF */
#define S_SPLT_ON 0x01 /* Split ON */
#define S_DUP_OFF 0x10 /* Simplex mode */
#define S_DUP_M 0x11 /* Duplex - mode */
#define S_DUP_P 0x12 /* Duplex + mode */
/*
* Set Attenuator (C_CTL_ATT) subcommands
*/
#define S_ATT_RD -1 /* Without subcommand, reads out setting */
#define S_ATT_OFF 0x00 /* Off */
#define S_ATT_6dB 0x06 /* 6 dB, IC-756Pro */
#define S_ATT_10dB 0x10 /* 10 dB */
#define S_ATT_12dB 0x12 /* 12 dB, IC-756Pro */
#define S_ATT_18dB 0x18 /* 18 dB, IC-756Pro */
#define S_ATT_20dB 0x20 /* 20 dB */
#define S_ATT_30dB 0x30 /* 30 dB, or Att on for IC-R75 */
/*
* Set Preamp (S_FUNC_PAMP) data
*/
#define D_PAMP_OFF 0x00
#define D_PAMP1 0x01
#define D_PAMP2 0x02
/*
* Set AGC (S_FUNC_AGC) data
*/
#define D_AGC_FAST 0x00
#define D_AGC_MID 0x01
#define D_AGC_SLOW 0x02
#define D_AGC_SUPERFAST 0x03 /* IC746 pro */
/*
* Set antenna (C_SET_ANT) subcommands
*/
#define S_ANT_RD -1 /* Without subcommand, reads out setting */
#define S_ANT1 0x00 /* Antenna 1 */
#define S_ANT2 0x01 /* Antenna 2 */
/*
* Announce control (C_CTL_ANN) subcommands
*/
#define S_ANN_ALL 0x00 /* Announce all */
#define S_ANN_FREQ 0x01 /* Announce freq */
#define S_ANN_MODE 0x02 /* Announce operating mode */
/*
* Function settings (C_CTL_LVL) subcommands
*/
#define S_LVL_AF 0x01 /* AF level setting */
#define S_LVL_RF 0x02 /* RF level setting */
#define S_LVL_SQL 0x03 /* SQL level setting */
#define S_LVL_IF 0x04 /* IF shift setting */
#define S_LVL_APF 0x05 /* APF level setting */
#define S_LVL_NR 0x06 /* NR level setting */
#define S_LVL_PBTIN 0x07 /* Twin PBT setting (inside) */
#define S_LVL_PBTOUT 0x08 /* Twin PBT setting (outside) */
#define S_LVL_CWPITCH 0x09 /* CW pitch setting */
#define S_LVL_RFPOWER 0x0a /* RF power setting */
#define S_LVL_MICGAIN 0x0b /* MIC gain setting */
#define S_LVL_KEYSPD 0x0c /* Key Speed setting */
#define S_LVL_NOTCHF 0x0d /* Notch freq. setting */
#define S_LVL_COMP 0x0e /* Compressor level setting */
#define S_LVL_BKINDL 0x0f /* BKin delay setting */
#define S_LVL_BALANCE 0x10 /* Balance setting (Dual watch) */
#define S_LVL_AGC 0x11 /* AGC (7800) */
#define S_LVL_NB 0x12 /* NB setting */
#define S_LVL_DIGI 0x13 /* DIGI-SEL (7800) */
#define S_LVL_DRIVE 0x14 /* DRIVE gain setting */
#define S_LVL_MON 0x15 /* Monitor gain setting */
#define S_LVL_VOXGAIN 0x16 /* VOX gain setting */
#define S_LVL_ANTIVOX 0x17 /* Anti VOX gain setting */
#define S_LVL_CONTRAST 0x18 /* CONTRAST level setting */
#define S_LVL_BRIGHT 0x19 /* BRIGHT level setting */
/*
* Read squelch condition/S-meter level/other meter levels (C_RD_SQSM) subcommands
*/
#define S_SQL 0x01 /* Read squelch condition */
#define S_SML 0x02 /* Read S-meter level */
#define S_RFML 0x11 /* Read RF-meter level */
#define S_SWR 0x12 /* Read SWR-meter level */
#define S_ALC 0x13 /* Read ALC-meter level */
#define S_CMP 0x14 /* Read COMP-meter level */
#define S_VD 0x15 /* Read Vd-meter level */
#define S_ID 0x16 /* Read Id-meter level */
/*
* Function settings (C_CTL_FUNC) subcommands Set and Read
*/
#define S_FUNC_PAMP 0x02 /* Preamp setting */
#define S_FUNC_AGCOFF 0x10 /* IC-R8500 only */
#define S_FUNC_AGCON 0x11 /* IC-R8500 only */
#define S_FUNC_AGC 0x12 /* AGC setting presets: the dsp models allow these to be modified */
#define S_FUNC_NBOFF 0x20 /* IC-R8500 only */
#define S_FUNC_NBON 0x21 /* IC-R8500 only */
#define S_FUNC_NB 0x22 /* NB setting */
#define S_FUNC_APFOFF 0x30 /* IC-R8500 only */
#define S_FUNC_APFON 0x31 /* IC-R8500 only */
#define S_FUNC_APF 0x32 /* APF setting */
#define S_FUNC_NR 0x40 /* NR setting */
#define S_FUNC_ANF 0x41 /* ANF setting */
#define S_FUNC_TONE 0x42 /* TONE setting */
#define S_FUNC_TSQL 0x43 /* TSQL setting */
#define S_FUNC_COMP 0x44 /* COMP setting */
#define S_FUNC_MON 0x45 /* Monitor setting */
#define S_FUNC_VOX 0x46 /* VOX setting */
#define S_FUNC_BKIN 0x47 /* BK-IN setting */
#define S_FUNC_MN 0x48 /* Manual notch setting */
#define S_FUNC_RF 0x49 /* RTTY Filter setting */
#define S_FUNC_AFC 0x4A /* Auto Frequency Control (AFC) setting */
#define S_FUNC_DTCS 0x4B /*DTCS tone code squelch setting*/
#define S_FUNC_VSC 0x4C /* voice squelch control useful for scanning*/
#define S_FUNC_MANAGC 0x4D /* manual AGC */
#define S_FUNC_DIGISEL 0x4E /* DIGI-SEL */
#define S_FUNC_TW_PK 0x4F /* RTTY Twin Peak filter 0= off 1 = on */
#define S_FUNC_DIAL_LK 0x50 /* Dial lock */
/*
* Set Power On/Off (C_SET_PWR) subcommands
*/
#define S_PWR_OFF 0x00
#define S_PWR_ON 0x01
/*
* Transmit control (C_CTL_PTT) subcommands
*/
#define S_PTT 0x00
#define S_ANT_TUN 0x01 /* Auto tuner 0=OFF, 1 = ON, 2=Start Tuning */
/*
* Misc contents (C_CTL_MEM) subcommands applies to newer rigs.
*/
#define S_MEM_CNTNT 0x00 /* Memory content 2 bigendian */
#define S_MEM_BAND_REG 0x01 /* band stacking register */
#define S_MEM_FILT_WDTH 0x03 /* current passband filter width */
#define S_MEM_PARM 0x05 /* rig parameters; extended parm # + param value: should be coded */
/* in the rig files because they are different for each rig */
#define S_MEM_DATA_MODE 0x06 /* data mode */
#define S_MEM_TX_PB 0x07 /* SSB tx passband */
#define S_MEM_FLTR_SHAPE 0x08 /* DSP filter shape 0=sharp 1=soft */
/* Icr75c */
#define S_MEM_CNTNT_SLCT 0x01
#define S_MEM_FLT_SLCT 0x01
#define S_MEM_MODE_SLCT 0x02
/* For IC-910H rig. */
#define S_MEM_RDWR_MEM 0x00 /* Read/write memory channel */
#define S_MEM_SATMEM 0x01 /* Satellite memory */
#define S_MEM_VOXGAIN 0x02 /* VOX gain level (0=0%, 255=100%) */
#define S_MEM_VOXDELAY 0x03 /* VOX delay (0=0.0 sec, 20=2.0 sec) */
#define S_MEM_ANTIVOX 0x04 /* anti VOX setting */
#define S_MEM_ATTLEVEL 0x05 /* Attenuation level (0=0%, 255=100%) */
#define S_MEM_RIT 0x06 /* RIT (0=off, 1=on, 2=sub dial) */
#define S_MEM_SATMODE 0x07 /* Satellite mode (on/off) */
#define S_MEM_BANDSCOPE 0x08 /* Simple bandscope (on/off) */
/*
* Tone control (C_SET_TONE) subcommands
*/
#define S_TONE_RPTR 0x00 /* Tone frequency setting for repeater receive */
#define S_TONE_SQL 0x01 /* Tone frequency setting for squelch */
#define S_TONE_DTCS 0x02 /* DTCS code and polarity for squelch */
/*
* Transceiver ID (C_RD_TRXID) subcommands
*/
#define S_RD_TRXID 0x00
/*
* C_CTL_MISC OptoScan extension
*/
#define S_OPTO_LOCAL 0x01
#define S_OPTO_REMOTE 0x02
#define S_OPTO_TAPE_ON 0x03
#define S_OPTO_TAPE_OFF 0x04
#define S_OPTO_RDSTAT 0x05
#define S_OPTO_RDCTCSS 0x06
#define S_OPTO_RDDCS 0x07
#define S_OPTO_RDDTMF 0x08
#define S_OPTO_RDID 0x09
#define S_OPTO_SPKRON 0x0a
#define S_OPTO_SPKROFF 0x0b
#define S_OPTO_5KSCON 0x0c
#define S_OPTO_5KSCOFF 0x0d
#define S_OPTO_NXT 0x0e
#define S_OPTO_SCON 0x0f
#define S_OPTO_SCOFF 0x10
/*
* OmniVIPlus (Omni VI) extensions
*/
#define C_OMNI6_XMT 0x16
/*
* S_MEM_MODE_SLCT Misc CI-V Mode settings
*/
#define S_PRM_BEEP 0x02
#define S_PRM_CWPITCH 0x10
#define S_PRM_LANG 0x15
#define S_PRM_BACKLT 0x21
#define S_PRM_SLEEP 0x32
#define S_PRM_SLPTM 0x33
#define S_PRM_TIME 0x27
/*
* Tokens for Extra Level and Parameters common to multiple rigs. Use token # > 99. Defined here so they
* will be available in ICOM name space. They have different internal commands primarily in dsp rigs. These
* tokens are used ext_lvl and ext_parm funtions in the individual rig files.
* Extra parameters which are rig specific should be coded in the individual rig files and token #s < 100.
*/
#define TOKEN_BACKEND(t) (t)
#define TOK_RTTY_FLTR TOKEN_BACKEND(100)
#define TOK_SSBBASS TOKEN_BACKEND(101)
#define TOK_SQLCTRL TOKEN_BACKEND(102)
#endif /* _ICOM_DEFS_H */