Hamlib/rigs/aor/ar8600.c

222 wiersze
6.2 KiB
C

/*
* Hamlib AOR backend - AR8600 description
* Copyright (c) 2000-2010 by Stephane Fillod
*
*
* This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU Lesser General Public
* License as published by the Free Software Foundation; either
* version 2.1 of the License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* Lesser General Public License for more details.
*
* You should have received a copy of the GNU Lesser General Public
* License along with this library; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
*
*/
#ifdef HAVE_CONFIG_H
#include "config.h"
#endif
#include <stdlib.h>
#include <hamlib/rig.h>
#include "aor.h"
#define AR8600_MODES (RIG_MODE_AM|RIG_MODE_CW|RIG_MODE_SSB|RIG_MODE_FM|RIG_MODE_WFM)
#define AR8600_FUNC (RIG_FUNC_TSQL|RIG_FUNC_ABM|RIG_FUNC_AFC)
#define AR8600_LEVEL (RIG_LEVEL_ATT|RIG_LEVEL_AGC|RIG_LEVEL_SQL|RIG_LEVEL_RAWSTR)
#define AR8600_PARM (RIG_PARM_APO|RIG_PARM_BACKLIGHT|RIG_PARM_BEEP)
#define AR8600_VFO_OPS (RIG_OP_MCL|RIG_OP_UP|RIG_OP_DOWN|RIG_OP_LEFT|RIG_OP_RIGHT)
#define AR8600_SCAN_OPS (RIG_SCAN_MEM|RIG_SCAN_VFO|RIG_SCAN_PROG|RIG_SCAN_SLCT)
#define AR8600_VFO_ALL (RIG_VFO_A|RIG_VFO_B|RIG_VFO_MEM)
/* Measurement by Mark, WAØTOP,
* using a HP8640B signal generator on an AR8600 Mark 2 (sn. 551454).
* The mode was AM. The ATT was off.
*/
#define AR8600_STR_CAL { 12, \
{ \
{ 0, -54 }, /* 1st point is extrapolated */ \
{ 13, -27 }, /* S-pixels: none */ \
{ 29, -17 }, \
{ 41, - 7 }, \
{ 49, 3 }, /* S-pixels: 21 */ \
{ 54, 13 }, \
{ 59, 23 }, \
{ 62, 33 }, /* S-pixels: 30 */ \
{ 64, 43 }, \
{ 65, 53 }, \
{ 68, 63 }, \
{ 69, 73 } /* S-pixels: 36 */ \
} }
#define AR8600_MEM_CAP { \
.freq = 1, \
.mode = 1, \
.width = 1, \
.bank_num = 1, \
.tuning_step = 1, \
.channel_desc = 1, \
.flags = 1, \
.levels = RIG_LEVEL_ATT, \
.funcs = RIG_FUNC_ABM, \
}
static const struct aor_priv_caps ar8600_priv_caps =
{
.format_mode = format8k_mode,
.parse_aor_mode = parse8k_aor_mode,
.bank_base1 = 'A',
.bank_base2 = 'a',
};
/*
* ar8600 rig capabilities.
* Notice that some rigs share the same functions.
* Also this struct is READONLY!
*
* part of info from http://www.aoruk.com/8600.htm
*/
const struct rig_caps ar8600_caps =
{
RIG_MODEL(RIG_MODEL_AR8600),
.model_name = "AR8600",
.mfg_name = "AOR",
.version = BACKEND_VER ".0",
.copyright = "LGPL",
.status = RIG_STATUS_BETA,
.rig_type = RIG_TYPE_SCANNER,
.ptt_type = RIG_PTT_NONE,
.dcd_type = RIG_DCD_RIG,
.port_type = RIG_PORT_SERIAL,
.serial_rate_min = 4800,
.serial_rate_max = 19200,
.serial_data_bits = 8,
.serial_stop_bits = 2,
.serial_parity = RIG_PARITY_NONE,
.serial_handshake = RIG_HANDSHAKE_XONXOFF,
.write_delay = 0,
.post_write_delay = 0,
.timeout = 200,
.retry = 3,
.has_get_func = RIG_FUNC_NONE,
.has_set_func = AR8600_FUNC,
.has_get_level = AR8600_LEVEL,
.has_set_level = RIG_LEVEL_SET(AR8600_LEVEL),
.has_get_parm = RIG_PARM_NONE,
.has_set_parm = RIG_PARM_NONE, /* FIXME: parms */
.level_gran = {}, /* FIXME: granularity */
.parm_gran = {},
.ctcss_list = NULL, /* FIXME: CTCSS list */
.dcs_list = NULL,
.preamp = { RIG_DBLST_END, },
.attenuator = { 20, RIG_DBLST_END, }, /* TBC */
.max_rit = Hz(0),
.max_xit = Hz(0),
.max_ifshift = Hz(0),
.targetable_vfo = 0,
.transceive = RIG_TRN_RIG,
.bank_qty = 20, /* A through J, and a trough j */
.chan_desc_sz = 12,
.vfo_ops = AR8600_VFO_OPS,
.scan_ops = AR8600_SCAN_OPS,
.str_cal = AR8600_STR_CAL,
.chan_list = {
{ 0, 999, RIG_MTYPE_MEM, AR8600_MEM_CAP }, /* flat space */
RIG_CHAN_END,
},
.rx_range_list1 = {
{kHz(100), MHz(2040), AR8600_MODES, -1, -1, AR8600_VFO_ALL},
RIG_FRNG_END,
}, /* rx range */
.tx_range_list1 = { RIG_FRNG_END, },
.rx_range_list2 = {
{kHz(100), MHz(2040), AR8600_MODES, -1, -1, AR8600_VFO_ALL},
RIG_FRNG_END,
}, /* rx range */
.tx_range_list2 = { RIG_FRNG_END, }, /* no tx range, this is a scanner! */
.tuning_steps = {
{AR8600_MODES, 50},
{AR8600_MODES, 100},
{AR8600_MODES, kHz(1)},
{AR8600_MODES, kHz(5)},
{AR8600_MODES, kHz(9)},
{AR8600_MODES, kHz(10)},
{AR8600_MODES, 12500},
{AR8600_MODES, kHz(20)},
{AR8600_MODES, kHz(25)},
{AR8600_MODES, kHz(100)},
{AR8600_MODES, MHz(1)},
#if 0
{AR8600_MODES, 0}, /* any tuning step */
#endif
RIG_TS_END,
},
/* mode/filter list, .remember = order matters! */
.filters = {
/* mode/filter list, .remember = order matters! */
{RIG_MODE_AM, kHz(9)},
{RIG_MODE_SSB | RIG_MODE_CW | RIG_MODE_AM, kHz(3)},
{RIG_MODE_FM | RIG_MODE_AM, kHz(12)},
{RIG_MODE_FM, kHz(9)},
{RIG_MODE_WFM, kHz(230)}, /* 150kHz at -3dB, 380kHz at -20dB */
RIG_FLT_END,
},
.priv = (void *)& ar8600_priv_caps,
.rig_init = NULL,
.rig_cleanup = NULL,
.rig_open = NULL,
.rig_close = aor_close,
.set_freq = aor_set_freq,
.get_freq = aor_get_freq,
.set_vfo = aor_set_vfo,
.get_vfo = aor_get_vfo,
.set_mode = aor_set_mode,
.get_mode = aor_get_mode,
.set_level = aor_set_level,
.get_level = aor_get_level,
.get_dcd = aor_get_dcd,
.set_ts = aor_set_ts,
.set_powerstat = aor_set_powerstat,
.vfo_op = aor_vfo_op,
.scan = aor_scan,
.get_info = aor_get_info,
.set_mem = aor_set_mem,
.get_mem = aor_get_mem,
.set_bank = aor_set_bank,
.set_channel = aor_set_channel,
.get_channel = aor_get_channel,
.get_chan_all_cb = aor_get_chan_all_cb,
};
/*
* Function definitions below
*/