/*
 *  Hamlib TenTenc backend - RX-350 description
 *  Copyright (c) 2003-2004 by Stephane Fillod
 *
 *
 *   This library is free software; you can redistribute it and/or
 *   modify it under the terms of the GNU Lesser General Public
 *   License as published by the Free Software Foundation; either
 *   version 2.1 of the License, or (at your option) any later version.
 *
 *   This library is distributed in the hope that it will be useful,
 *   but WITHOUT ANY WARRANTY; without even the implied warranty of
 *   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 *   Lesser General Public License for more details.
 *
 *   You should have received a copy of the GNU Lesser General Public
 *   License along with this library; if not, write to the Free Software
 *   Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301  USA
 *
 */

#ifdef HAVE_CONFIG_H
#include "config.h"
#endif

#include <stdlib.h>

#include <hamlib/rig.h>
#include "tentec2.h"
#include "bandplan.h"


#define RX350_MODES (RIG_MODE_FM|RIG_MODE_CW|RIG_MODE_SSB|\
            RIG_MODE_AM|RIG_MODE_AMS)

#define RX350_FUNCS (RIG_FUNC_NR|RIG_FUNC_ANF)

#define RX350_LEVELS (RIG_LEVEL_RAWSTR|/*RIG_LEVEL_NB|*/ \
                RIG_LEVEL_RF|RIG_LEVEL_IF| \
                RIG_LEVEL_AF|RIG_LEVEL_AGC| \
                RIG_LEVEL_SQL|RIG_LEVEL_ATT)

#define RX350_ANTS (RIG_ANT_1)

#define RX350_PARMS (RIG_PARM_TIME)

#define RX350_VFO (RIG_VFO_A|RIG_VFO_B)

#define RX350_VFO_OPS (RIG_OP_TO_VFO|RIG_OP_FROM_VFO)


/*
 * RX350 receiver capabilities.
 *
 * Protocol is documented at
 *      http://www.rfsquared.com/
 *
 * Only set_freq is supposed to work.
 * This is a skeleton.
 */
const struct rig_caps rx350_caps =
{
    RIG_MODEL(RIG_MODEL_RX350),
    .model_name = "RX-350",
    .mfg_name =  "Ten-Tec",
    .version =  BACKEND_VER ".0",
    .copyright =  "LGPL",
    .status =  RIG_STATUS_UNTESTED,
    .rig_type =  RIG_TYPE_RECEIVER,
    .ptt_type =  RIG_PTT_NONE,
    .dcd_type =  RIG_DCD_NONE,
    .port_type =  RIG_PORT_SERIAL,
    .serial_rate_min =  57600,
    .serial_rate_max =  57600,
    .serial_data_bits =  8,
    .serial_stop_bits =  1,
    .serial_parity =  RIG_PARITY_NONE,
    .serial_handshake =  RIG_HANDSHAKE_HARDWARE,
    .write_delay =  0,
    .post_write_delay =  0,
    .timeout =  400,
    .retry =  3,

    .has_get_func =  RX350_FUNCS,
    .has_set_func =  RX350_FUNCS,
    .has_get_level =  RX350_LEVELS,
    .has_set_level =  RIG_LEVEL_SET(RX350_LEVELS),
    .has_get_parm =  RX350_PARMS,
    .has_set_parm =  RX350_PARMS,
    .level_gran =  {},                 /* FIXME: granularity */
    .parm_gran =  {},
    .ctcss_list =  NULL,
    .dcs_list =  NULL,
    .preamp =   { RIG_DBLST_END },
    .attenuator =   { 20, RIG_DBLST_END },
    .max_rit =  Hz(0),
    .max_xit =  Hz(0),
    .max_ifshift =  kHz(2),
    .targetable_vfo =  RIG_TARGETABLE_FREQ | RIG_TARGETABLE_MODE,
    .transceive =  RIG_TRN_OFF,
    .bank_qty =   8,
    .chan_desc_sz =  15,

    .chan_list =  {
        {   0, 127, RIG_MTYPE_MEM, TT_MEM_CAP },
    },

    .rx_range_list1 =  {
        {kHz(100), MHz(30), RX350_MODES, -1, -1, RX350_VFO, RX350_ANTS},
        RIG_FRNG_END,
    },
    .tx_range_list1 =  {
        RIG_FRNG_END,
    },

    .rx_range_list2 =  {
        {kHz(100), MHz(30), RX350_MODES, -1, -1, RX350_VFO, RX350_ANTS},
        RIG_FRNG_END,
    },
    .tx_range_list2 =  {
        RIG_FRNG_END,
    },

    .tuning_steps =  {
        {RX350_MODES, 1},
        RIG_TS_END,
    },
    /* mode/filter list, remember: order matters! */
    .filters =  {
        {RX350_MODES, kHz(2.4)},
        {RX350_MODES, 300},
        {RX350_MODES, kHz(8)},
        {RX350_MODES, 0}, /* 34 filters */
        RIG_FLT_END,
    },
    .priv = (void *)NULL,

    .set_freq =  tentec2_set_freq,
    .get_freq =  tentec2_get_freq,
    .set_vfo =  tentec2_set_vfo,
    .get_vfo =  tentec2_get_vfo,
    .set_mode =  tentec2_set_mode,
    .get_mode =  tentec2_get_mode,
    .reset =  tentec2_reset,
    .get_info =  tentec2_get_info,

};

/*
 * Function definitions below
 */