/*
 *  Hamlib CI-V backend - description of the OptoScan456
 *  Copyright (c) 2000-2002 by Stephane Fillod
 *
 *		$Id: os456.c,v 1.1 2002-03-10 23:36:19 fillods Exp $
 *
 *   This library is free software; you can redistribute it and/or modify
 *   it under the terms of the GNU Library General Public License as
 *   published by the Free Software Foundation; either version 2 of
 *   the License, or (at your option) any later version.
 *
 *   This program is distributed in the hope that it will be useful,
 *   but WITHOUT ANY WARRANTY; without even the implied warranty of
 *   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *   GNU Library General Public License for more details.
 *
 *   You should have received a copy of the GNU Library General Public
 *   License along with this library; if not, write to the Free Software
 *   Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 *
 */

#ifdef HAVE_CONFIG_H
#include "config.h"
#endif

#include <hamlib/rig.h>
#include "icom.h"
#include "tones.h"


#define OS456_MODES (RIG_MODE_AM|RIG_MODE_FM|RIG_MODE_WFM)

#define OS456_VFO_ALL (RIG_VFO_A)

#define OS456_LEVELS (RIG_LEVEL_STRENGTH)

/*
 * The signal strength data is in the form of two bytes, each consisting 
 * of two BCD digits. The signal strength is reported in units of absolute 
 * dBm as measured at the antenna connector. The reported signal strength 
 * ranges from a maximum signal of 0 dBm to a minimum signal of - 125 dBm. 
 * A minus sign is implied.
 */

#define OS456_STR_CAL { 2, { \
		{ 125, -60 }, \
		{ 0, 60 }, \
		} }		/* TBC */

/*
 * The OptoScan is not actually a rig. This is an add-in circuit board
 * for the Realistic PRO-2006 and PRO-2005 Scanning VHF-UHF Receivers.
 * http://www.optoelectronics.com/tech/pdf/os535/os535_ci5_spec_v10.pdf
 *
 * TODO: srch_dcs, srch_ctcss, rcv_dtmf, and make icom_probe opto aware
 */

static const struct icom_priv_caps os456_priv_caps = { 
		0x80,	/* default address */
		0,		/* 731 mode */
		NULL,
		OS456_STR_CAL
};

const struct rig_caps os456_caps = {
rig_model: RIG_MODEL_OS456,
model_name:"OptoScan456", 
mfg_name: "Optoelectronics", 
version: "0.2", 
copyright: "LGPL",
status: RIG_STATUS_UNTESTED,
rig_type: RIG_TYPE_SCANNER,
ptt_type: RIG_PTT_NONE,
dcd_type: RIG_DCD_NONE,
port_type: RIG_PORT_SERIAL,
serial_rate_min: 300,
serial_rate_max: 38400,
serial_data_bits: 8,
serial_stop_bits: 1,
serial_parity: RIG_PARITY_NONE,
serial_handshake: RIG_HANDSHAKE_NONE, 
write_delay: 0,
post_write_delay: 0,
timeout: 200,
retry: 3, 
has_get_func: RIG_FUNC_NONE,
has_set_func: RIG_FUNC_NONE, 
has_get_level: RIG_LEVEL_NONE,
has_set_level: RIG_LEVEL_NONE,
has_get_parm: RIG_PARM_NONE,
has_set_parm: RIG_PARM_NONE,
level_gran: {},
parm_gran: {},
ctcss_list: full_ctcss_list,
dcs_list: full_dcs_list,
preamp:  { RIG_DBLST_END, },
attenuator:  { RIG_DBLST_END, },
max_rit: Hz(0),
max_xit: Hz(0),
max_ifshift: Hz(0),
targetable_vfo: 0,
vfo_ops: RIG_OP_NONE,
scan_ops: RIG_SCAN_NONE,
transceive: RIG_TRN_RIG,
bank_qty:  0,
chan_desc_sz: 0,

chan_list: { RIG_CHAN_END, },

rx_range_list1:  {
	{ MHz(25),MHz(520),OS456_MODES,-1,-1,OS456_VFO_ALL},
	{ MHz(760),MHz(1300),OS456_MODES,-1,-1,OS456_VFO_ALL},
	RIG_FRNG_END, },
tx_range_list1: { RIG_FRNG_END, },		/* this is a scanner */

rx_range_list2:  {
	{ MHz(25),MHz(520),OS456_MODES,-1,-1,OS456_VFO_ALL},
	{ MHz(760),MHz(823.995),OS456_MODES,-1,-1,OS456_VFO_ALL},
	{ MHz(849),MHz(868.995),OS456_MODES,-1,-1,OS456_VFO_ALL},
	{ MHz(894),MHz(1300),OS456_MODES,-1,-1,OS456_VFO_ALL},
	RIG_FRNG_END, },
tx_range_list2: { RIG_FRNG_END, },		/* this is a scanner */

tuning_steps:	{
	 {OS456_MODES,kHz(5)},
	 {OS456_MODES,kHz(12.5)},
	 {OS456_MODES,kHz(50)},
	 RIG_TS_END,
	},
	/* mode/filter list, remember: order matters! */
filters:	{
		{RIG_MODE_AM|RIG_MODE_FM|RIG_MODE_WFM, kHz(15)},	/* TBC */
		RIG_FLT_END,
	},

cfgparams: icom_cfg_params,
set_conf: icom_set_conf,
get_conf: icom_get_conf,

priv: (void*)&os456_priv_caps,
rig_init:  icom_init,
rig_cleanup:  icom_cleanup,
rig_open: optoscan_open,
rig_close: optoscan_close,

set_freq: icom_set_freq,
get_freq: icom_get_freq,
set_mode: icom_set_mode,
get_mode: icom_get_mode,
set_vfo: icom_set_vfo,

get_level: icom_get_level,
get_dcd: icom_get_dcd,

decode_event: icom_decode_event,

get_info: optoscan_get_info,

};