This implementation reduces the number of VFO excahnges or sets to a
minimum when setting the TX VFO frequency and mode together.
This also includes a much smarter implementation of the logic used
when the new config option 'no_xchg' is enabled. Now it is able to
accurately determine the original VFO selected and leaves the
sequences with the same VFO selected. There is one corner case when
both VFOs are identical (frequency, mode and width) at the start where
it has to take a guess as to the selected originally VFO (Icom CAT
protocol has no command to elicit this information). In that case it
guesses as the last VFO selected using Hamlib. Applications can gain
absolute certainty by setting the VFO themselves prior to using the
rig_{set,get}_{split,}_{freq,mode,freq_mode}() function series. This
now gives seamless TX VFO configuration without any relay clattering
or TX/RX audio glitches.
Icom users, who use the K9JM CI-V router to protect their PW-1
amplifiers from damage due to Icom's broken CI-V protocol handling,
require a 1s delay after opening the serial port. This is due to the
router using an Arduino & Arduino USB adapter that employs a
bootloader which holds the RS-232 interface for 1s after reset (DTR
releases reset). Hamlib already has a retry and timeout mechanism
which was set to 3 and 200ms respectively for most Icom rigs. This
change increses that timeout to 1s. The increaased timeout will have
little or no impact on clients as it only comes into play if there is
a problem.
With Icom rigs that use MAIN?SUB VFOs there is a trade off when
setting the mode or frequency of the "other" VFO. Untill now Hamlib
uses the XCHG VFO command to address the "other" VFO. This has some
advantages, particularly it preserves the selected VFO and it
preserves memory mode of either VFO. The disadvantage is that any
split command causes the Rx to glitch when the VFO/MEMs are exchanged.
I have added a config parameter for Icom rigs called "no_xchg" which
forces the direct addressing of VFOs to set split mode/frequency. It
is a boolean option with a default of "0" (false) which equates to
prior behaviour. Setting it to "1" (true) will make the backend use
change VFO commands to set the "other" VFO. This means that TX on
"SUB" in split is assumed, that both are in VFO mode (not MEM), and
set/get split functions will leave the MAIN VFO selected.
The Icom IC-7x6Pro models support AFSK data modes with Tx audio
delivered via the back ACC socket. This mode is enabled and queried
via a separate "0x1A06" command and applies to USB, LSB, FM and, AM as
USB-D, LSB-D, FM-D and, AM-D respectively on the radio. I have added
all but AM because hamlib has no mode enumeration for AM Data mode.
Most of the IC-7xxx rigs have an extended version of this special
command which also involves width. This needs further work to
implement.
Signed-off-by: Nate Bargmann <n0nb@n0nb.us>
The IC-756 only has two filters per mode unlike the later IC-756
variants that have three. The code was sending invalid commands
due to trying to select the third filter for certain bandwidths.
Also the default filter bandwidths were incorrect for this model.
Signed-off-by: Nate Bargmann <n0nb@n0nb.us>
73
Bill.
>From 5209463ba169516543e2666b8b3a98b605c362e6 Mon Sep 17 00:00:00 2001
From: Bill Somerville <g4wjs@classdesign.com>
Date: Sat, 20 Jul 2013 01:45:01 +0100
Subject: [PATCH] All IC-756 varieties have MAIN/SUB VFOs rather than A/B VFOs
In the past IC-756ProIII capabiities have been updated to use MAIN/SUB VFO
commands but as far as I can tell from the user manuals for the IC-756,
IC-756Pro, IC-756Pro2 all varieties have the MAIN/SUB VFOs and need to use
the correct VFO access sub command.
I have an IC-756 and discovered this defect via WSJT-X which as of v1.1
requires split operation setup.
Signed-off-by: Nate Bargmann <n0nb@n0nb.us>
* The 746 has an APF, wasn't in its configuration, added, tested, works.
* The 756Pro has an ANF function, wasn't in its configuration, added,
tested, works.
* The 756Pro's signal strength conversion table was way wrong.
I noticed this while making scope plots in my program JRX --
the strong signals using the STRENGTH output would all flatten
out at a rather low level, but the RAWSTR output showed the
full range. Changed the conversion table, tested, fixed.
R8500 notes:
The R8500 on/off functions work differently than the other Icoms,
in fact it's not too strong to say that this radio is a breed apart.
Most Icom radios have a group command code for on/off functions (16),
then a code for the function, then a flag for on or off. The R8500
combines the second and third into one, and this required a bit of
recoding in "icom.c". Interestingly, someone had created some special
designators in "icom_defs.h" for the R8500, but then never coded them
to the degree that they worked. Now they work. :)
So the AGC, NB and APF functions all work now.
The R8500 doesn't have a preamp control, so I took that out.
The R8500 does have IF shift and a 3-step attenuater, so I put those in.
Signed-off-by: Nate Bargmann <n0nb@n0nb.us>
Darrel, AK6I, has an IC-756 (non-Pro model) and reports several
functions are not supported and suggested they be modified.
(cherry picked from commit 11033470f0)
to set_split_vfo/get_split_vfo, and take an extra transmit vfo arg.
Ascending compatibility is retained at the API frontend level.
NOTE: only function name has changed. The backends do not implement
necessarily the new semantic (the extra tx vfo is just ignored).
git-svn-id: https://hamlib.svn.sourceforge.net/svnroot/hamlib/trunk@1425 7ae35d74-ebe9-4afe-98af-79ac388436b8
Mikael Nousiainen