Hamlib/wj/wj8888.c

/*
 *  Hamlib Watkins-Johnson backend - WJ-8888 description
 *  Copyright (c) 2004 by Stephane Fillod
 *
 *	$Id: wj8888.c,v 1.2 2006-10-07 18:55:19 csete Exp $
 *
 *   This library is free software; you can redistribute it and/or modify
 *   it under the terms of the GNU Library General Public License as
 *   published by the Free Software Foundation; either version 2 of
 *   the License, or (at your option) any later version.
 *
 *   This program is distributed in the hope that it will be useful,
 *   but WITHOUT ANY WARRANTY; without even the implied warranty of
 *   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *   GNU Library General Public License for more details.
 *
 *   You should have received a copy of the GNU Library General Public
 *   License along with this library; if not, write to the Free Software
 *   Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 *
 */

#ifdef HAVE_CONFIG_H
#include "config.h"
#endif

#include <stdlib.h>

#include <hamlib/rig.h>
#include "idx_builtin.h"
#include "wj.h"


/* modes: what about ISB(Idependant Sideband)? */
#define WJ8888_MODES (RIG_MODE_AM|RIG_MODE_CW|RIG_MODE_SSB|RIG_MODE_FM|RIG_MODE_AMS)

#define WJ8888_FUNC (RIG_FUNC_NONE)

#define WJ8888_LEVEL (RIG_LEVEL_RF|RIG_LEVEL_AGC|RIG_LEVEL_IF|RIG_LEVEL_RAWSTR)

#define WJ8888_VFO (RIG_VFO_A)

/* FIXME: real measures */
#define WJ8888_STR_CAL { 2, \
	{ \
		{  0x00, -60 }, /* -115.5dBm .. -99.5dBm */ \
		{  0x7f, 60 } \
	} }

/*
 * WJ-8888 receiver capabilities.
 *
 * Needs async I/O board
 *
 *
 * TODO: BFO
 */
const struct rig_caps wj8888_caps = {
.rig_model =  RIG_MODEL_WJ8888,
.model_name = "WJ-8888",
.mfg_name =  "Watkins-Johnson",
.version =  "0.2",
.copyright =  "LGPL",
.status =  RIG_STATUS_UNTESTED,
.rig_type =  RIG_TYPE_RECEIVER,
.ptt_type =  RIG_PTT_NONE,
.dcd_type =  RIG_DCD_NONE,
.port_type =  RIG_PORT_SERIAL,
.serial_rate_min =  75,		/* jumper E26 */
.serial_rate_max =  9600,	/* jumper E19 */
.serial_data_bits =  8,
.serial_stop_bits =  1,		/* jumper between E5 & E6 */
.serial_parity =  RIG_PARITY_NONE,	/* no jumper between E3 & E4 */
.serial_handshake =  RIG_HANDSHAKE_NONE,
.write_delay =  0,
.post_write_delay =  5,	/* typical 5ms, max 15ms */
.timeout =  2000,
.retry =  3,

.has_get_func =  WJ8888_FUNC,
.has_set_func =  WJ8888_FUNC,
.has_get_level =  WJ8888_LEVEL,
.has_set_level =  RIG_LEVEL_SET(WJ8888_LEVEL),
.has_get_parm =  RIG_PARM_NONE,
.has_set_parm =  RIG_PARM_NONE,
.vfo_ops =  RIG_OP_NONE,
.preamp =   { RIG_DBLST_END },
.attenuator =   { RIG_DBLST_END },
.level_gran = {
	[LVL_RAWSTR] = { .min = { .i = 0 }, .max = { .i = 0x7f } },
},
.max_rit =  Hz(0),
.max_xit =  Hz(0),
.max_ifshift =  kHz(8),	/* IF at 455kHz */
.targetable_vfo =  0,
.transceive =  RIG_TRN_OFF,
.bank_qty =   0,
.chan_desc_sz =  0,
.str_cal = WJ8888_STR_CAL,

.cfgparams = wj_cfg_params,

.chan_list =  { RIG_CHAN_END, },

.rx_range_list1 =  {
	{kHz(500),MHz(30),WJ8888_MODES,-1,-1,WJ8888_VFO},
	RIG_FRNG_END,
  },
.tx_range_list1 =  { RIG_FRNG_END, },
.rx_range_list2 =  {
	{kHz(500),MHz(30),WJ8888_MODES,-1,-1,WJ8888_VFO},
	RIG_FRNG_END,
  },
.tx_range_list2 =  { RIG_FRNG_END, },

.tuning_steps =  {
	 {WJ8888_MODES,10},
	 RIG_TS_END,
	},
        /* mode/filter list, remember: order matters! */
.filters =  {
		{WJ8888_MODES, kHz(2)},
		{WJ8888_MODES, Hz(500)},
		{WJ8888_MODES, kHz(4)},
		{WJ8888_MODES, kHz(8)},
		/* option (in spare, to be fixed) */
		{WJ8888_MODES, Hz(200)},
		{WJ8888_MODES, kHz(1)},
		{WJ8888_MODES, kHz(3)},
		{WJ8888_MODES, kHz(6)},
		{WJ8888_MODES, kHz(12)},
		{WJ8888_MODES, kHz(16)},
		RIG_FLT_END,
	},

.rig_init =  wj_init,
.rig_cleanup =  wj_cleanup,
.set_conf =  wj_set_conf,
.get_conf =  wj_get_conf,

.set_freq =  wj_set_freq,
.get_freq =  wj_get_freq,
.set_mode =  wj_set_mode,
.get_mode =  wj_get_mode,
.set_level =  wj_set_level,
.get_level =  wj_get_level,

};

/*
 * Function definitions below
 */