kopia lustrzana https://github.com/Hamlib/Hamlib
86 wiersze
3.2 KiB
Plaintext
86 wiersze
3.2 KiB
Plaintext
|
The following email describes the command set used by the Rotor-EZ
|
||
|
|
interface for Hy-Gain rotors and the RotorCard interface for Yaesu
|
||
|
|
rotors manufactured and sold by Idiom Press, http://www.idiompres.com
|
||
|
|
|
||
|
|
The Hy-Gain DCU-1/DCU-1X Digital Control Unit supports a subset of
|
||
|
|
these commands--AP1XXX; and AM1; The DCU-1/DCU-1X is manufactured
|
||
|
|
and sold by Hy-Gain, http://www.hy-gain.com
|
||
|
|
|
||
|
|
$Id: rotorez.txt,v 1.1 2003-01-12 14:29:15 n0nb Exp $
|
||
|
|
|
||
|
|
From: "sales@idiompress.com" <info@idiompress.com>
|
||
|
|
To: "Nate Bargmann" <n0nb@arrl.net>
|
||
|
|
Subject: Re: Rotor Card and Rotor-EZ command reference
|
||
|
|
Date: Fri, 10 Jan 2003 09:38:52 -0800
|
||
|
|
|
||
|
|
Here you go:
|
||
|
|
|
||
|
|
Important note: The program you are using must insert leading zeros into
|
||
|
|
bearing commands, such as "009" degrees, instead of "9" degrees. Most
|
||
|
|
programs are already configured this way, but some are not in their default
|
||
|
|
mode, and in such cases you must change the default setting or the RS-232
|
||
|
|
portion of Rotor-EZ will not work properly.
|
||
|
|
|
||
|
|
Rotor-EZ can also be commanded from any terminal having RS232 output, using
|
||
|
|
the following configuration: 4800 baud, 8,N,1 Note that upper case/lower
|
||
|
|
case must be used as listed for the commands below to work:
|
||
|
|
|
||
|
|
"AP1xxx<CR>" sets target bearing to "xxx" degrees where xxx are three digits
|
||
|
|
between 000 and 360, and executes. A typical command to rotate to 080
|
||
|
|
degrees would be AP1080<CR> Note that the <CR> is often labeled <Enter> on
|
||
|
|
many keyboards.
|
||
|
|
|
||
|
|
"AP1xxx;" sets the target bearing but does not execute.
|
||
|
|
"AM1;" executes rotation to the bearing set by the "AP1xxx;" command
|
||
|
|
"AI1;" inquires current bearing; and responds with (000-359) degrees
|
||
|
|
";" terminates rotation
|
||
|
|
"E" enable endpoint option - effective immediately
|
||
|
|
"e" disable endpoint option - effective immediately
|
||
|
|
"O" enable overshoot option - effective immediately
|
||
|
|
"o" disable overshoot option - effective immediately
|
||
|
|
"S" enable unstick option - effective immediately
|
||
|
|
"s" disable unstick option - effective immediately
|
||
|
|
"V" reports version number
|
||
|
|
"J" enable jam protection - effective immediately
|
||
|
|
"j" disable jam protection - effective immediately - NOT recommended!
|
||
|
|
|
||
|
|
Note that during any rotation initiated by an RS232 command, the rotation
|
||
|
|
can be halted and further rotation cancelled by a momentary press of the
|
||
|
|
Brake paddle. Also, an RS232 operation can be overridden by using the
|
||
|
|
pointing control during rotation; when the control is moved rotation will
|
||
|
|
cease and the control will wait for a new command after the five second
|
||
|
|
brake delay is completed.
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
73
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
----- Original Message -----
|
||
|
|
From: Nate Bargmann <n0nb@arrl.net>
|
||
|
|
To: <sales@idiompress.com>
|
||
|
|
Sent: Friday, January 10, 2003 8:23 AM
|
||
|
|
Subject: Rotor Card and Rotor-EZ command reference
|
||
|
|
|
||
|
|
|
||
|
|
> Hi!
|
||
|
|
>
|
||
|
|
> I am working with a software project called Hamlib
|
||
|
|
> http://hamlib.sourceforge.net and I would like to add support for the
|
||
|
|
> Rotor Card and Rotor-EZ into our library. In the course of several Web
|
||
|
|
> searches I have downloaded the Hy-Gain DCU-1 manual from their site and
|
||
|
|
> I've also visited the Digital Audio Rotor-EZ troubleshooting site.
|
||
|
|
> Between the two I have found a couple of descrepancies in the command
|
||
|
|
> set. If possible, I would like a copy of the complete command set and
|
||
|
|
> their syntax for these two boards for our project.
|
||
|
|
>
|
||
|
|
> Thanks!
|
||
|
|
>
|
||
|
|
> 73, de Nate >>
|
||
|
|
>
|
||
|
|
|
||
|
|
|
||
|
|
|