Hamlib/wj/wj8888.c

154 wiersze
3.8 KiB
C
Czysty Zwykły widok Historia

/*
* Hamlib Watkins-Johnson backend - WJ-8888 description
* Copyright (c) 2004 by Stephane Fillod
*
* $Id: wj8888.c,v 1.2 2006-10-07 18:55:19 csete Exp $
*
* This library is free software; you can redistribute it and/or modify
* it under the terms of the GNU Library General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU Library General Public License for more details.
*
* You should have received a copy of the GNU Library General Public
* License along with this library; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
*/
#ifdef HAVE_CONFIG_H
#include "config.h"
#endif
#include <stdlib.h>
#include <hamlib/rig.h>
#include "idx_builtin.h"
#include "wj.h"
/* modes: what about ISB(Idependant Sideband)? */
#define WJ8888_MODES (RIG_MODE_AM|RIG_MODE_CW|RIG_MODE_SSB|RIG_MODE_FM|RIG_MODE_AMS)
#define WJ8888_FUNC (RIG_FUNC_NONE)
#define WJ8888_LEVEL (RIG_LEVEL_RF|RIG_LEVEL_AGC|RIG_LEVEL_IF|RIG_LEVEL_RAWSTR)
#define WJ8888_VFO (RIG_VFO_A)
/* FIXME: real measures */
#define WJ8888_STR_CAL { 2, \
{ \
{ 0x00, -60 }, /* -115.5dBm .. -99.5dBm */ \
{ 0x7f, 60 } \
} }
/*
* WJ-8888 receiver capabilities.
*
* Needs async I/O board
*
*
* TODO: BFO
*/
const struct rig_caps wj8888_caps = {
.rig_model = RIG_MODEL_WJ8888,
.model_name = "WJ-8888",
.mfg_name = "Watkins-Johnson",
.version = "0.2",
.copyright = "LGPL",
.status = RIG_STATUS_UNTESTED,
.rig_type = RIG_TYPE_RECEIVER,
.ptt_type = RIG_PTT_NONE,
.dcd_type = RIG_DCD_NONE,
.port_type = RIG_PORT_SERIAL,
.serial_rate_min = 75, /* jumper E26 */
.serial_rate_max = 9600, /* jumper E19 */
.serial_data_bits = 8,
.serial_stop_bits = 1, /* jumper between E5 & E6 */
.serial_parity = RIG_PARITY_NONE, /* no jumper between E3 & E4 */
.serial_handshake = RIG_HANDSHAKE_NONE,
.write_delay = 0,
.post_write_delay = 5, /* typical 5ms, max 15ms */
.timeout = 2000,
.retry = 3,
.has_get_func = WJ8888_FUNC,
.has_set_func = WJ8888_FUNC,
.has_get_level = WJ8888_LEVEL,
.has_set_level = RIG_LEVEL_SET(WJ8888_LEVEL),
.has_get_parm = RIG_PARM_NONE,
.has_set_parm = RIG_PARM_NONE,
.vfo_ops = RIG_OP_NONE,
.preamp = { RIG_DBLST_END },
.attenuator = { RIG_DBLST_END },
.level_gran = {
[LVL_RAWSTR] = { .min = { .i = 0 }, .max = { .i = 0x7f } },
},
.max_rit = Hz(0),
.max_xit = Hz(0),
.max_ifshift = kHz(8), /* IF at 455kHz */
.targetable_vfo = 0,
.transceive = RIG_TRN_OFF,
.bank_qty = 0,
.chan_desc_sz = 0,
.str_cal = WJ8888_STR_CAL,
.cfgparams = wj_cfg_params,
.chan_list = { RIG_CHAN_END, },
.rx_range_list1 = {
{kHz(500),MHz(30),WJ8888_MODES,-1,-1,WJ8888_VFO},
RIG_FRNG_END,
},
.tx_range_list1 = { RIG_FRNG_END, },
.rx_range_list2 = {
{kHz(500),MHz(30),WJ8888_MODES,-1,-1,WJ8888_VFO},
RIG_FRNG_END,
},
.tx_range_list2 = { RIG_FRNG_END, },
.tuning_steps = {
{WJ8888_MODES,10},
RIG_TS_END,
},
/* mode/filter list, remember: order matters! */
.filters = {
{WJ8888_MODES, kHz(2)},
{WJ8888_MODES, Hz(500)},
{WJ8888_MODES, kHz(4)},
{WJ8888_MODES, kHz(8)},
/* option (in spare, to be fixed) */
{WJ8888_MODES, Hz(200)},
{WJ8888_MODES, kHz(1)},
{WJ8888_MODES, kHz(3)},
{WJ8888_MODES, kHz(6)},
{WJ8888_MODES, kHz(12)},
{WJ8888_MODES, kHz(16)},
RIG_FLT_END,
},
.rig_init = wj_init,
.rig_cleanup = wj_cleanup,
.set_conf = wj_set_conf,
.get_conf = wj_get_conf,
.set_freq = wj_set_freq,
.get_freq = wj_get_freq,
.set_mode = wj_set_mode,
.get_mode = wj_get_mode,
.set_level = wj_set_level,
.get_level = wj_get_level,
};
/*
* Function definitions below
*/