Improved README

README.md

@@ -37,7 +37,7 @@ You can add monophonic sound by referencing a WAV file as follows:
 sudo ./pi_fm_rds -wav sound.wav
 ```
 
-**Current limitation: the WAV file must be sampled at 228 kHz. Use for instance the two files provided, `sound.wav` and `pulses.wav`.**
+**Current limitation: the WAV file must be sampled at 228 kHz. Use for instance the two files provided, `sound.wav` and `pulses.wav`. I'm working on lifting this restriction.**
 
 The more general syntax for running Pi-FM-RDS is as follows:
 
@@ -47,12 +47,12 @@ pi_fm_rds [-freq freq] [-wav file.wav] [-ppm ppm_error] [-pi pi_code] [-ps ps_te
 
 All arguments are optional:
 
-* `-freq` specifies a frequency (in MHz). Example: `-freq 87.5`.
-* `-wav` specifies a WAV file to play. It must be sampled at 228 kHz, but no frequency above 18 kHz must be present. Example: `-wav sound.wav`.
-* `-ppm` specifies your Raspberry Pi's oscillator error in parts per million (ppm), see below.
+* `-freq` specifies the carrier frequency (in MHz). Example: `-freq 107.9`.
+* `-wav` specifies a WAV file to play as audio. It must be sampled at 228 kHz, but no frequency above 18 kHz must be present. Example: `-wav sound.wav`.
 * `-pi` specifies the PI-code of the RDS broadcast. 4 hexadecimal digits. Example: `-pi FFFF`.
 * `-ps` specifies the station name (Program Service name, PS) of the RDS broadcast. Limit: 8 characters. Example: `-ps RASP-PI`.
 * `-rt` specifies the radiotext (RT) to be transmitted. Limit: 64 characters. Example: `-rt 'Hello, world!'`.
+* `-ppm` specifies your Raspberry Pi's oscillator error in parts per million (ppm), see below.
 
 By default the PS changes back and forth between `Pi-FmRds` and a sequence number, starting at `00000000`. The PS changes around one time per second.
 
@@ -63,16 +63,18 @@ The RDS standards states that the error for the 57 kHz subcarrier must be less t
 
 In practice, I found that Pi-FM-RDS works okay even without using the `-ppm` parameter. I suppose the receiver are more tolerant than stated in the RDS spec.
 
-One way to measure the ppm error is to play the `pulses.wav` file: it will play a pulse for precisely 1 second, then play a 1-second silence, and so on. Record the audio output from a radio with a good audio card. Say you sample at 44.1 kHz. Measure 10 intervals. Using [Audacity](http://audacity.sourceforge.net/) for example determine the number of samples of these 10 intervals: in the absence of clock error, it should be 441,000 samples. With my Pi, I found 441,132 samples. Therefore, my ppm error is (441132-441000)/441000 * 1e6 = 299 ppm, **assuming that my sampling device has no clock error...**
+One way to measure the ppm error is to play the `pulses.wav` file: it will play a pulse for precisely 1 second, then play a 1-second silence, and so on. Record the audio output from a radio with a good audio card. Say you sample at 44.1 kHz. Measure 10 intervals. Using [Audacity](http://audacity.sourceforge.net/) for example determine the number of samples of these 10 intervals: in the absence of clock error, it should be 441,000 samples. With my Pi, I found 441,132 samples. Therefore, my ppm error is (441132-441000)/441000 * 1e6 = 299 ppm, **assuming that my sampling device (audio card) has no clock error...**
 
 
-## Diclaimer
+## Warning and Diclaimer
 
 Never use this program to transmit VHF-FM data through an antenna, as it is
 illegal in most countries. This code is for experimental purposes only.
 Always connect a shielded transmission line from the RaspberryPi directly
 to a radio receiver, so as **not** to emit radio waves.
 
+I could not be held liable for any misuse of your own Raspberry Pi. Any experiment is made under your own responsibility.
+
 
 ## Tests
 
@@ -82,7 +84,7 @@ Pi-FM-RDS was successfully tested with all my RDS-able devices, namely:
 * a Sangean PR-D1 portable receiver from 1998,
 * a Samsung Galaxy S2 mobile phone from 2011,
 * a Philips MBD7020 hifi system from 2012,
-* a Silicon Labs [USBFMRADIO-RD](http://www.silabs.com/products/mcu/Pages/USBFMRadioRD.aspx) USB stick, employing an Si4701 chip, using my [RDS Surveyor](http://rds-surveyor.sourceforge.net/) program,
+* a Silicon Labs [USBFMRADIO-RD](http://www.silabs.com/products/mcu/Pages/USBFMRadioRD.aspx) USB stick, employing an Si4701 chip, and using my [RDS Surveyor](http://rds-surveyor.sourceforge.net/) program,
 * a “PCear Fm Radio”, a Chinese clone of the above, again using RDS Surveyor.
 
 Reception works perfectly with all the devices above. RDS Surveyor reports no group errors.
@@ -97,7 +99,7 @@ The RDS data generator generates cyclically four 0A groups (for transmitting PS)
 
 To get samples of RDS data, call `get_rds_samples`. It calls `get_rds_group`, differentially encodes the signal and generates a shaped biphase symbol. Successive biphase symbols overlap: the samples are added so that the result is equivalent to applying the shaping filter (a [root-raised-cosine (RRC) filter ](http://en.wikipedia.org/wiki/Root-raised-cosine_filter) specified in the RDS standard) to a sequence of Manchester-encoded pulses.
 
-The shaped biphase symbol is generated by a Python program called `generate_waveforms.py` that uses [Pydemod](https://github.com/ChristopheJacquet/Pydemod), one of my other software radio projects. This Python program generates an array called `waveform_biphase` that results from the application of the RRC filter to a positive-negative impulse pair.
+The shaped biphase symbol is generated once and for all by a Python program called `generate_waveforms.py` that uses [Pydemod](https://github.com/ChristopheJacquet/Pydemod), one of my other software radio projects. This Python program generates an array called `waveform_biphase` that results from the application of the RRC filter to a positive-negative impulse pair. *Note that the output of `generate_waveforms.py`, two files named `waveforms.c` and `waveforms.h`, are included in the Git repository, so you don't need to run the Python script yourself to compile Pi-FM-RDS.*
 
 The samples are played by `pi_fm_rds.c` that is adapted from Richard Hirst's [PiFmDma](https://github.com/richardghirst/PiBits/tree/master/PiFmDma). The program was changed to support a sample rate of precisely 228 kHz, four times the RDS subcarrier's 57 kHz.