kopia lustrzana https://github.com/SnkMtn000/Arduino-RFM69HCW-GPS
58 wiersze
2.7 KiB
Plaintext
58 wiersze
2.7 KiB
Plaintext
|
Notes and disclaimer on the Osh Park Board:
|
||
|
|
||
|
This is not a perfect board. I'll be the first to admit this. It most certainly has short commings. It is designed
|
||
|
to use an arduino pro mini board of the 3.3v flavor. Do not attempt to use a 5.0v version of this board as
|
||
|
the Hope RFM69HCW will be destroyed.
|
||
|
|
||
|
1) The SMA foot print I found online is not a perfect match. The copper pad for the signal pin on the back
|
||
|
of the board needs to be exposed. I do this by gently scraping off the coating with a knife. I also found I had to
|
||
|
cut off two grounds and bend the signal pin to get it to fit the tickeness of the board. May just be the cheap SMA
|
||
|
I got online!
|
||
|
|
||
|
2) I inadvertainly place the pin assignments for GPS backwards meaning it needs to be mounted on the back of the board.
|
||
|
Refer to JPGs.
|
||
|
|
||
|
3) The foot print for the Arduino pro mini 3.3 volt has plated through holes that are not connectd to anything.
|
||
|
The only plated through holes that should be used are the two rows of header as shown in the photos.
|
||
|
|
||
|
4) I could not find a foot print for the RFM69HCW and rolled my own. I will publish OSH Park files here
|
||
|
at a future date including my foot print.
|
||
|
|
||
|
This board is designed for the RFM69HCW, 433 or 915 MHz chips. It will not work with any other variation
|
||
|
of the RFM69xxx family. It will not work with LORA chips. It most certainly will not work with an
|
||
|
RFM22b!!!!!
|
||
|
|
||
|
Assembly:
|
||
|
|
||
|
1) The boards I recieved work perfectly . I recommend assembly in this order.
|
||
|
|
||
|
2) Ring out the bare board before assembly. Why not? If you do not know what that means google it.
|
||
|
|
||
|
3) Tin with solder one corner pad only. Place the rfm69hcw follwing the orientation as printed on the board.
|
||
|
Heat and relow the solder to stick the IC to the board. Make sure it is oriented evenly on each pad before
|
||
|
continuing.
|
||
|
|
||
|
4) Once happy with the orientation solder another corner pad but more securely. The a third pad. The go back
|
||
|
and ensure the first pad you soldered had a good elctrical bond. If not reflow again.
|
||
|
|
||
|
5) Solder every other pad and give it time to cool. Go back and finish solder the rest of the pad.
|
||
|
|
||
|
6) I next solder onthe 2 12xpin headers. I like headers for socketing the arduino. It allows reuse. BUT,...
|
||
|
the beast way I found to do this was to first put pins on the arduino, then press the headers on the pins,
|
||
|
then into the board and solder as above.
|
||
|
|
||
|
7) The board requires the serial adapter to program but can operate with the GPS using a 5V-12V battery
|
||
|
on the RAW pin, on the P1 header.
|
||
|
|
||
|
8) If it does not work out of the can, then please ring it out again. It is not impossible to have
|
||
|
created a solder bridge between pads of the rfm69 or...an open due to not enough solder between pads.
|
||
|
|
||
|
:)
|
||
|
|
||
|
Good luck.
|
||
|
|
||
|
|
||
|
|
||
|
|
||
|
|